Roofing Installation Mistakes to Avoid - Bansal Roofing Products Limited

1
Roofing Installation Mistakes to Avoid
A roof is the crown of a construction structure,
ultimate protection over construction that
protects from extreme conditions. Thus, a roof
must be selected, manufactured and installed with
proper precaution and high standards ensuring
that it not only provides protection but also
adds to the aesthetics of construction. It is
important that the roofing sheet you select
checks off all the requirements of the ideal
roofing for your construction. One of the
materials that have been surpassing many for ages
is metal both steel and aluminium. Metal roofing
sheets have been in business for centuries and
have gained immense popularity owing to the
versatility and benefits they offer. However, the
metal roofing installation is a crucial aspect.
If not installed in an appropriate manner, it can
result in several shortcomings like leakage and
render the construction to be weak over time,
outshining the benefits a metal roof provides.
Bansal Roofing has been in the roofing business
for a long time and has acquired enough expertise
to give you some advice and tips on mistakes you
can avoid when installing the metal roof of your
choice.
Common Mistakes To Avoid In Roofing
Installation 1 Incorrect Screw Fasteners
2
It is important to inquire regarding the kind of
screw fasteners your roofing manufacturer uses
when installing your metal roof. Making use of
non-standard screws for the metal roofing
installation can result in water leakage and
cause the roof to become weak in the long run. It
is important to use the correct fasteners that
are designed especially for metal roof panels.
The objective of using fasteners is to seal the
opening through a washer, keeping the water at
bay. Quality is yet another factor that must be
considered because compromising the quality of
your metal roof will cost you in the long
run. 2 Overlapping the Panel in the Wrong
Manner Overlapping the metal roof panels is of
key importance as it prevents the water to leak
from areas where the panels meet. The overlapping
required depends upon the slope of the roof. It
is imperative to determine the pitch of the roof
in accordance with the amount of overlap required
and other requisites that must be suggested and
executed by the roofing manufacturers. Also
Read Why are Steel Structure Buildings
Recommended? 3 Extension of Roof Panels
Appropriately Over the Edge
Precision is important when leaving just the
correct amount of roof overhanging. If the roof
is altered too short, there will eventually be
water leakage down to the sides and the gutters.
On the other hand, if the metal roof is extended
too long then the water will not enter the
gutters and eventually result in falling directly
to the ground. Hence, it is suggested by
construction experts to keep the measurements of
the overhang around an inch and a half and 2
inches. 4 Using Few Screws for Pipe
Flashing Penetrations like PVC pipes are more
prone to leakage and such penetrations must be
flashed with utmost care and caution. It is
crucial to make use of the right number of screws
and avoid
3
the use of caulk as an alternative. Also Read
Top 9 Advantages of Aluminium Roofing Sheets 5
Too Much Reliability on Sealant Sealants and
caulks are not the primary options for
waterproofing. It must be ensured that the
application of caulk should be kept away from
sunlight and weather. The best and safest
position for its application is underneath a
panel or trim. Metal is used for several
purposes like roof decking, cladding and much
more. Metal is a material preferred by many and
metal roofs are the finest option for any
construction. With Bansal roofing, one neednt
worry about the quality, durability and timely
delivery of roofing sheets and roofing
accessories. Bansal roofing is the pioneer of
manufacturing premium quality roofing sheets,
roofing accessories and PEB constructions. We
believe in catering to our customers
construction needs with utmost precision and
offering them full value for their money. Bansal
delivers roofing accessories, products and PEB
Constructions PAN INDIA and is known for timely
delivery and high quality of products. Having
catered to the metal roofing needs of big
industries and several private enterprises,
Bansal roofing manufactures metal roofing sheets
meeting every clients construction requirements
with top-notch quality. Original Source
https//www.bansalroofing.com/roofing-installation
- mistakes-to-avoid/