Power of Ethernet Direct PoE Product Line Overview

1
Power of Ethernet DirectPoE Product Line
Overview
2
Introduction

• What is PoE
• 802.3af Standard in Brief
• What is PSE
• Sample Diagram of MidSpan Endpoint Connection
• What is PD
• PoE Product Line Introduction
• Managed PoE Switch
• PoE Software Settings
• Unmanaged PoE Switch
• Others
• Sample PoE Connection Diagram
• Surveillance-Factory Premises
• Transportation-Tunnel Application
• PoE Technology in the Future
• IEEE802.3at (PoE)

3
What is PoE

• Power over Ethernet is a mechanism for supplying
  power to network devices over the same cabling
  used to carry network traffic. PoE allows devices
  that require power (PD) and supply the power
  (PSE) over existing infrastructure without
  needing to upgrade it.
• This feature can simplify network installation
  and maintenance by using the switch as a central
  power source for other network devices.

4
What is PoE - 802.3af Standard in Brief

• 802.3af, also known as Power over Ethernet,
  defines a way to build Ethernet power-sourcing
  equipment and powered terminals.
• The specification involves delivering 48 volts of
  DC power over unshielded twisted-pair wiring.
• It works with existing cable plant, including
  Category 3, 5, 5e or 6.
• The technology supports a point-to-multipoint
  power distribution architecture, parallel to the
  data network.
• The total amount of continuous power that can be
  delivered to each node is 12.95 watts. (max. load
  power 15.4W, after counting cable lost left
  12.95W)
• 802.3af power sourcing equipment contains a
  detection mechanism to prevent sending power to
  noncompliant devices.

5
What is PoE What is PSE

• PSE Power Sourcing Equipment
• The PSE is the equipment that provides power to
  PDs. The PSEs main functions are
• To search the link section for a PD.
• Optionally classify the PD.
• Supply power to the link section. (only if a PD
  is detected)
• Monitor the power on the link section.
• 802.3af defines two types of power source
  equipment Endpoint and Mid-span.
• Endpoint refers to an Ethernet switch with
  embedded Power over Ethernet technology.
• Midspan devices are usually placed between legacy
  switches and the powered devices.

With PoE injector built-in, EDs PoE switch
products are perfect solution for Endpoint
applications.
6
Sample Diagram of MidSpan Endpoint Connection
Sample of PoE Midspan Connection
Sample of PoE Endpoint Connection
6
7
What is PoE What is PD

• PD Powered Device
• A PD is a device that is either drawing power or
  requesting power from PSE.
• The Power Class of PD
• Once a PD is discovered, a PSE may optionally
  perform PD classification by applying a DC
  voltage and current to the port, allocated power
  is subtracted from total power budget.
• Any unclassified PD is considered to be a class 0
  device.
• Class 3 is similar to Class 0 in that it also
  requests full power, but a Class 3 PD will always
  draw at least 7W according to the standard,
  whereas a Class 0 device could draw anything up
  to full power

8
PoE Product Line Introduction

• Managed PoE Switch
• CME-822EIndustrial 8 10/100TX 2 SFP port with
  8 PoE Injector Managed Switch
• Unmanaged PoE Switch
• CUE-111 113Industrial 1 10/100TX 1 100FX
  with 1 PoE Injector unmanaged Switch
• CUE-411 413Industrial 4 10/100TX 1 100FX
  with 4 PoE Injector unmanaged Switch
• CUE-500 Industrial 5 10/100TX with 4 PoE
  Injector unmanaged Switch
• Others
• CUS-100GIndustrial PoE splitter for 10/100/1000T

9
PoE Product Line Introduction Managed PoE Switch

• CME-822EIndustrial 8 10/100TX 2 SFP port with
  8 PoE Injector Managed Switch
• IEEE 802.3af Power over Ethernet Compliant Power
  Supply
• DC 48V Redundant Power
• EFT protection 3000 VDC for power line
• 4000 VDC Ethernet ESD protection
• Manageable Software Features
• The built-in software has the same features as
  HMG-828 (ex. VLAN, IGMP, SNMP, X-Ring.)
• Additional PoE Software Features built-in
• Port Knockoff detection, PoE Port Enable/Disable,
  Enable/Disable PD Power Class detection, Port
  Priority

10
PoE Product Line Introduction Managed PoE Switch
(PoE Software settings)
10
11
PoE Product Line Introduction Managed PoE Switch
(PoE Software settings)

• Maximum Power Available Displays the maximum
  power supply in watts.
• Actual Power Consumption This column shows the
  real-time total power consumption
• System Power Limit User can modify the value to
  this column field to limit the total output power
  for the system
• Main Supply Voltage This column shows the output
  voltage of the system for PoE ports
• Firmware Version This column shows the PoE
  chips firmware version
• Port Knockoff Disabled Power Management state
  where one or more PDs have been powered down so
  that a higher priority PD may be powered up and
  yet not exceed the maximum total power available
  for PDs
• AC Disconnect Tick this checkbox to monitor the
  AC impedance on the port terminals and removes
  power when the impedance rises above a certain
  value, for a certain period
• Capacitive Detection If the port and capacitive
  detection are enabled, the capacitances state
  reads in the voltage result from the constant
  current. This is then subtracted from the
  pre-capacitance voltage to get a charge rate. If
  this charge rate is within the window of the PD
  signatures, the device is considered to be
  discovered.
• Start Showing with a tick symbol, the system
  initializes and resets successfully

11
12
PoE Product Line Introduction Managed PoE Switch
(PoE Software settings)

• Port The index of PoE ports.
• Enable State Check it to enable the PoE function
  to the port.
• Power Limit From Classification Check it to
  decide the power limit method when this check
  box is ticked, the system will limit the power
  supply to the powered device in accordance with
  the related class
• Legacy Check it to support the legacy power
  devices. (PDs may not have IEEE802.3 standard
  detection signature)
• Priority Pull down the selection menu item to
  choose the priority of power supplying.
• Port Limit (lt15400) mW User can key in the power
  limit value which is under 15.4 Watts.
• Mode Displays the operating mode of the port.
• Current (mA) Displays the operating current of
  the port.
• Voltage (V) Displays the operating voltage of
  the port.
• Power (mW) Displays the power consumption of the
  port.
• Determined Class Displays the PDs class.

12
13
PoE Product Line Introduction Unmanaged PoE
Switch

• CUE-111 113 Industrial 1 10/100TX 1 100FX
  with 1 PoE Injector unmanaged Switch
• IEEE 802.3af Power over Ethernet compliant
• RJ-45 port support Auto MDI/MDI-X Function
• Embedded 1 port PoE Injector Function
• CUE-111 for multimode fiber port
• CUE-113 for single mode fiber port
• Power Supply
• DC 48V Redundant Power
• EFT protection 3000 VDC for power line
• 4000 VDC Ethernet ESD protection

14
PoE Product Line Introduction Unmanaged PoE
Switch

• CUE-411 413 Industrial 4 10/100TX 1 100FX
  with 4 PoE Injector unmanaged Switch
• IEEE 802.3af Power over Ethernet compliant
• RJ-45 port support Auto MDI/MDI-X Function
• Embedded 4 port PoE Injector Function
• CUE-411 for multimode fiber port
• CUE-413 for single mode fiber port
• Power Supply
• DC 48V Redundant Power
• EFT protection 3000 VDC for power line
• 4000 VDC Ethernet ESD protection

15
PoE Product Line Introduction Unmanaged PoE
Switch

• CUE-500 Industrial 5 10/100TX with 4 PoE
  Injector unmanaged Switch
• IEEE 802.3af Power over Ethernet compliant
• RJ-45 port support Auto MDI/MDI-X Function
• Embedded 4 port PoE Injector Function
• Power Supply
• DC 48V Redundant Power
• EFT protection 3000 VDC for power line
• 4000 VDC Ethernet ESD protection

16
PoE Product Line Introduction Others

• CUS-100G Industrial PoE splitter for
  10/100/1000T
• Support 10/100/1000T for PoE in and Data out
• Power Isolation and Short Circuit Protection for
  power output
• Provides EFT protection 3000 VDC for power line
• Power Supply support output power up to 25W at
  24VDC (we offer 12/24/48V products for customize
  order request)
• IP-30 Housing protection
• DIN rail and wall mount installation

17
Sample of PoE Connection Diagram
18
Sample of PoE Application Diagram(Surveillance-Fa
ctory Premises)
18
19
Sample of PoE Application Diagram(Transportation-
Tunnel Application)
19
20
PoE Technology In The FutureIEEE802.3at (PoE)

• The enhancement of the PoE is to increase the
  amount of power that can be supplied from PSE to
  the PDs, via the Cat-5, Cat-5e, Cat-6 unshielded
  twisted pair wiring.
• The new specification attempts to bring the power
  supplied up to at least 24 watts. (draft 3.0
  proposed 30W in draft 2.0)
• New standard may have approve by year 2009 with
  the enhancement mentioned above.
• With new standard apply there will have more PD
  available for PoE applications, eg Security IP
  Camera with pan/tilt/zoom capabilities, door
  controllers, POS terminals, videophones and
  dual-band wireless access points.etc.