Ultrasound Physics

1
Ultrasound Physics

• 04Scanner

97
2
Resonant Frequency

• Frequency of Highest Sustained Intensity
• Transducers preferred or resonant frequency
• Examples
• Guitar String
• Bell

3
Pulse Mode Ultrasound

• transducer driven by short voltage pulses
• short sound pulses produced
• Like plucking guitar string
• Pulse repetition frequency same as frequency of
  applied voltage pulses
• determined by the instrument (scanner)

4
Pulse Duration Review
Pulse Duration Period X Cycles / Pulse

• typically 2-3 cycles per pulse
• Transducer tends to continue ringing
• minimized by dampening transducer element

5
Damping Material

• Goal
• reduce cycles / pulse
• Method
• dampen out vibrations after voltage pulse
• Construction
• mixture of powder plastic or epoxy
• attached to near face of piezoelectric element
  (away from patient)

Damping Material
Piezoelectric Element
6
Disadvantages of Damping

• reduces beam intensity
• produces less pure frequency (tone)

7
Bandwidth

• Damping shortens pulses
• the shorter the pulse, the higher the range of
  frequencies
• Range of frequencies produced called bandwidth

8
Bandwidth

• range of frequencies present in an ultrasound
  pulse

Ideal
OperatingFrequency
Intensity
Frequency
9
Quality Factor (Q)

• operating
  frequencyQuality Factor -----------------------
  ------ bandwidth

• Unitless
• Quantitative Measure of Spectral Purity

Bandwidth
10
Which has a Higher Quality Factor?

• operating
  frequencyQuality Factor -----------------------
  ------ bandwidth

A
B
Intensity
Intensity
Frequency
Frequency
Same Operating Frequency!
11
Damping

• More damping results in
• shorter pulses
• more frequencies
• higher bandwidth
• lower quality factor
• lower intensity
• Rule of thumb
• for short pulses (2 - 3 cycles)
• quality factor number of cycles per pulse

12
An Aside about Reflections

• Echoes occur at interfaces between 2 media of
  different acoustic impedances
• speed of sound X density

Medium 1
Medium 2
13
Intensity Reflection Coefficient
(IRC)Intensity Transmission Coefficient (ITC)

• IRC
• Fraction of sound intensity reflected at
  interface
• lt1
• ITC
• Fraction of sound intensity transmitted through
  interface
• lt1

Medium 1
IRC ITC 1
Medium 2
14
IRC Equation
For perpendicular incidence
reflected intensity z2 - z1 IRC
------------------------ ----------
incident intensity z2 z1

• Z1 is acoustic impedance of medium 1
• Z2 is acoustic impedance of medium 2

Medium 1
Medium 2
15
Reflections

• Impedances equal
• no reflection
• Impedances similar
• little reflected
• Impedances very different
• virtually all reflected

16
Why Use Gel?
reflected
intensity z2 - z1
IRC ------------------------ ----------
incident intensity
z2 z1
Acoustic Impedance (rayls)
Air 400
Soft Tissue 1,630,000
Fraction Reflected 0.9995

• Acoustic Impedance of air soft tissue very
  different
• Without gel virtually no sound penetrates skin

17
Transducer Matching Layer

• Transducer element has different acoustic
  impedance than skin
• Matching layer reduces reflections at surface of
  piezoelectric element
• Increases sound energy transmitted into body

18
Transducer Matching Layer

• placed on face of transducer
• impedance between that of transducer tissue
• reduces reflections at surface of piezoelectric
  element
• Creates several small transitions in acoustic
  impedance rather than one large one

Matching Layer
19
Transducer Arrays

• Virtually all commercial transducers are arrays
• Multiple small elements in single housing
• Allows sound beam to be electronically
• Focused
• Steered
• Shaped

20
Electronic Scanning

• Transducer Arrays
• Multiple small transducers
• Activated in groups

21
Electrical Scanning

• Performed with transducer arrays
• multiple elements inside transducer assembly
  arranged in either
• a line (linear array)
• concentric circles (annular array)

22
Linear Array Scanning

• Two techniques for activating groups of linear
  transducers
• Switched Arrays
• activate all elements in group at same time
• Phased Arrays
• Activate group elements at slightly different
  times
• impose timing delays between activations of
  elements in group

23
Linear Switched Arrays

• Elements energized as groups
• group acts like one large transducer
• Groups moved up down through elements
• same effect as manually translating
• very fast scanning possible (several times per
  second)
• results in real time image

24
Linear Switched Arrays
25
Linear Phased Array

• Groups of elements energized
• same as with switched arrays
• voltage pulse applied to all elements of a
  groupBUT
• elements not all pulsed at same time

1
2
26
Linear Phased Array

• timing variations allow beam to be
• shaped
• steered
• focused

Above arrows indicate timing variations. By
activating bottom element first top last, beam
directed upward
Beam steered upward
27
Linear Phased Array
Above arrows indicate timing variations. By
activating top element first bottom last, beam
directed downward
Beam steered downward
By changing timing variations between pulses,
beam can be scanned from top to bottom
28
Linear Phased Array
Focus
Above arrows indicate timing variations. By
activating top bottom elements earlier than
center ones, beam is focused
Beam is focused
29
Linear Phased Array
Focus
Focal point can be moved toward or away from
transducer by altering timing variations between
outer elements center
30
Linear Phased Array
Focus

• Multiple focal zones accomplished by changing
  timing variations between pulses
• Multiple pulses required
• slows frame rate

31
Listening Mode

• Listening direction can be steered focused
  similarly to beam generation
• appropriate timing variations applied to echoes
  received by various elements of a group
• Dynamic Focusing
• listening focus depth can be changed
  electronically between pulses by applying timing
  variations as above

2