BIS PRODUCT CERTIFICATION SCHEME CYCLE COMPONENTS

1
BIS PRODUCT CERTIFICATION SCHEME CYCLE
COMPONENTS
2

• ACQUIRING
• BIS
• LICENCE

3
HOW TO GET BIS LICENCE

• FOR THE BENEFIT OF INDUSTRY
• BUREAU OF INDIAN STANDARDS ( BIS)
• HAS SIMPLIFIED THE SCHEME FOR
• GRANT OF BIS LICENCE
• THERE ARE TWO SCHEMES
• 1) SCHEME 1
• Foreign Manufacturers Scheme
• Indian Importers Scheme

4

• IMPORTANT POINTS IN THE SCHEME
• Applicant is required to furnish the test report
  (s) of the sample (s) got tested by them in the
  laboratories along with the application and
  requisite fee.
• List of approved laboratories from where
• samples could be got tested has been put
• in the BIS home page which can be seen
• at www.bis.org.in

5

• 2) SCHEME 2
• FOR GRANT OF LICENCE FOR
• DOMESTIC MANUFACTURERS
• WE ARE CONCERNED WITH THIS SCHEME
• ONLY.

6

• THE SCHEME HAS TWO OPTIONS
• a) Application along with Self
• evaluation form, Test Report (s) from a
  recognized independent lab, Testing
  Manufacturing facilities verified by a CHARTERED
  ENGINEER with an
• application fee of Rs 1000.00 only S T as
  applicable

7

• b) Application along with Self
• evaluation form, Test Report (s)
• from an independent lab,
• Testing Manufacturing facilities
• with an application fee of Rs 1000
• 4000.00 (Visit fee) only S T
• as applicable

8

• In case the testing laboratory for the
• required product is not listed in the
  approved list given in above site the samples can
  be got tested from
• a) All BIS accredited laboratories.
• b) Labs of CSIR, ICAR and other
• similar laboratories.
• c) All labs under control of Central
• Govt. like NTH, RTC etc.
• d) All labs under control of State Govt.
• which are NABL accredited.

9

• e) All Labs of National Level
• Institutions like IITs, National
• Metallurgical Institute etc.
• f) Labs of Department of Central
• Universities.
• g) Labs of National Institute of
• Technologies.

10

• FIRST OPTION
• VERIFICATION OF
• APPLICATION FACILITIES
• BY
• CHARTERED ENGINEER

11

• Application duly certified by a Chartered
• Engineer to be submitted to concerned BIS
• office. The licence then shall be granted
• after scrutiny of the documents and
• report submitted by Chartered Engineer.
• By this procedure the licence is expected
• to be granted same day of receipt of
• application by BIS, provided all required
• documents are furnished and found
• satisfactory.

12

• After grant of licence surveillance visit will be
  paid by an inspecting officer from Bureau of
  Indian standards, who will verify the
  manufacturing and testing facilities and carry
  out factory testing of the product.

13

• A sample is also drawn for independent testing
  if every thing is found satisfactory licence will
  continue.
• If the sample is found failing, marking shall be
  stopped immediately and a notice for cancellation
  of Licence shall be given.
• Decision on cancellation shall be taken based on
  the merit of the case and as per BIS Act, Rules
  and Regulations.

14

• THE SECOND OPTION
• VERIFICATION OF FACILITIES
• BY
• INSPECTING OFFICER
• OF
• BUREAU OF INDIAN STANDARDS

15

• Application duly filled along with Self-
• Evaluation cum Verification report-Test
• Report from independent lab along
• with fee is submitted to BIS office.
• The documents are scrutinized.
• The licence shall be granted after a
• visit is paid to the firm by an inspecting
• officer.
• The purpose is to verify capabilities of the
  organization with respect to Manufacturing and
  Testing facilities and competence of Quality of
  Assurance Personnel.

16

• During the visit, sample(s) of product from
  regular production is also tested, sealed for
  Independent Testing in BIS approved laboratory.
• The case will be reviewed on receipt of the
  reports.
• If the sample is found failing, marking shall be
  stopped immediately and a notice for cancellation
  of Licence shall be given.
• Decision on cancellation shall be taken based on
  the merit of the case and as per BIS Act, Rules
  and Regulations.

17

• WHAT DOCUMENTS
• ARE
• TO BE SUBMITTED
• FOR
• GETTING BIS LICENCE

18

• Application (Form 1) (to be submitted by the
• applicant)
• Self Evaluation Report (Form II) (to be
• submitted by the applicant along
• with application)
• Verification of the Self Evaluation Report (by
  
• BIS-Section B of Form II/by Chartered
  Engineer - Section C of Form II)
• Test report (s) submitted by the applicant meets
  the criteria of the ISS applied for
  (Verification to be done by BIS). Test report (s)
  submitted shall not be older than one month
  covering all requirements including long term
  tests, if any and tests on all raw materials
  (conformity of which have been specified as
  mandatory in the relevant Indian Standard).

19

• Testing shall be got done according to the
  relevant ISS from any of the labs indicated above
  for the particular product. Where applicant is
  using BIS Standard Marked raw materials, the
  applicant shall not be required to furnish test
  report of these raw materials. However,
  verification of such raw materials shall be done
  by BIS officer during verification
  visit/surveillance visit (if verification is done
  by Chartered Engineer) and samples of the same
  may be drawn for testing in BIS or its recognized
  laboratories as a market sample.

20

• For products, where there is no testing
  facility available in any of the laboratories
  indicated above, licence shall be granted based
  on testing in the factory for which the applicant
  should have Complete testing facility in-house
  for all tests as per related Indian Standards.

21

• THE APPLICATION FORM
• DOC FILE1

22

• Self Evaluation Report (Form II)
• DOC FILE2

23

• Verification of the Self Evaluation Report by
  Chartered Engineer
• DOC FILE2

24

• Test report (s)
• from
• Independent Laboratory
• Showing
• conformity to ISS

25

• SITE LOCATION PLAN

26

• DETAILS OF RAW MATERIALS
• WITH
• APPLICABLE ISS CONFORMITY

27

• PROCESS FLOW CHART
• WITH
• CRITICAL CONTROLS

28

• DETAILS
• OF
• PRODUCT MANUFACTURING

29

• DETAILS
• OF
• MANUFACTURING FACILITIES

30

• DETAILS
• OF
• TESTING EQUIPMENTS

31

• APPOINTMENT
• OF
• QUALITY CONTROL PERSON
• ALONG WITH
• QUALIFICATIONS
• EXPERENCE

32

• CALIBRATION CERTIFICATES
• OF
• TEST EQUIPMENTS

33

• WEEKLY OFF DECLARATION

34

• VALIDITY OF LICENCE
• The initial validity period of the licence is one
  year. Licence can be renewed for further period
  of one/two years, subject to satisfactory
  operation of licence as observed during periodic
  inspections, factory independent testing of
  samples drawn from factory and market. The
  licensee shall apply to BIS on the prescribed
  Renewal Form along with renewal application fee
  of Rs. 500/- and annual licence fee of Rs. 1000/-
  and advance minimum marking fee.

35

• THANK YOU
• GENTLEMEN

36
DISCUSSIONS

• ANY QUESTION PLEASE

37
IS SPECIFICATIONS

• IS 623
• IS 2061
• IS 2403
• IS 2414
• 2415
• 6218

38

• IS 623 1993
• BICYCLE FRAME
• TOTAL NO. 01
• PANJAB 01

39

• IS 2061
• BICYCLE FORKS
• TOTAL NO. 01
• PANJAB 1

40

• IS 2403 1991
• SHORT PITCH TRANSMISSION PRECISION
• ROLLER CHAINS
• TOTAL NO. 7
• CHANDIGARH 01
• GUJRAT 02
• PUNJAB 01
• RAJASTHAN 01
• TAMIL NAIDU 02

41

• IS 24141991
• CYCLE RICKSHAW PNEUMATIC TYRES
• TOTAL NO 07
• MADHYA PARDESH 01
• PANJAB 06

42

• IS 24151992
• CYCLE RUBBER TUBES
• TOTAL NO. 05
• MADHYA PARDESH 01
• PANJAB 04