Title: RPFT Braindumps
1Pass (RPFT) Registry Examination for Advanced
Pulmonary Function Technologists exam in just 24
HOURS! 100 REAL EXAM QUESTIONS ANSWERS (RPFT)
Registry Examination for Advanced
Pulmonary Function Technologists Buy Complete
Questions Answers File from http//www.exams4sure.
com/NBRC/RPFT-practice-exam-dumps.html 100 Exam
Passing Guarantee Money Back Assurance
Sample Questions
2- Question No 1
- Which of the following is the most reliable
method to estimate the effectiveness of standard
procedures to minimize the risk of
cross-contamination during spirometry testing in
a pulmonary function laboratory? - Count the number of disposable mouthpieces used
for 1 week. - Observe the handwashing behavior of each
technologist. - Ask patients tested about laboratory hygiene.
- Ask technologists if they wash their hands before
each test - Answer B Question No 2
- While performing duplicate blood gas analyses, a
pulmonary function technologist notes that the
second instrument gives consistently higher
values forPaCO2and PaO2. Which of the following
is the most probable cause of higher readings
from the second instrument? - The sample chamber temperature is greater than
37 C - An excessive delay occurred between running the
two samples - The PO2and PCO2electrodemembranes have protein
build-up - The sample chamber has a bacterial contaminate
- Answer A Question No 3
- Which of the following problems may be identified
by using an isothermal lung analog to perform
quality control on a body plethysmograph? - 1.Improperly calibrated mouth pressure transducer
- 2.Obstructed or perforated pneumotachometer
- 3.Increase in mechanical resistance
- 4.Malfunctioning box pressure transducer
3- Question No 4
- An isothermal lung analog has the following
specifications 5-L glass bottle - 2000 g of steel wool
- Density of steel wool 5 g/cm3
- Volume of connectors and bulb 100 mi-Repeated FRC
measurements in the plethysmograph result in a
volume of 5.5 L. Which of the following should a
pulmonary function technologist do? - Remove 500 g ofsteel wool from the lung analog
- Take the plethysmograph out of service
- Recalculate the BTPS correction
- Begin a biologic control program
- Answer D Question No 5
- A pulmonary function technologist is reviewing an
asthma action plan. The patient takes a low-dose
inhaled corticosteroid and a long-acting
beta2-agonist twice daily. The patient's
personal best peak flow is 600 L/min. Which of
the following instructions should be given to
the patient when the peak flow drops to 500
L/min? - Add montelukast (Singular).
- Continue the current regimen.
- Go to the emergency department.
- Double the steroid dose.
- Answer A Question No 6
- A treadmill belt stops for a fraction of a second
each time the patient takes a step. A pulmonary
function technologist should - Instruct the patient to use the hand rails.
- Tighten the belt.
4- Question No 7
- Prior to an exercise study, a pulmonary function
technologist finds that the patient's RER is - Which of the following best explains this
finding? - Carbohydrate metabolism
- Protein metabolism
- Hypoventilation
- Hyperventilation
- Answer D Question No 8
- A 6-year-old child has a history of repeated
episodes of wheezing and shortness of breath. A
pulmonary function technologist has difficulty
obtaining repeatable spirometry results. - Which of the following tests should be performed
next? - MVV
- DLco
- SGaw
- SpO2
- Answer A Question No 9
- A pulmonary function technologist is performing
an exercise (stress) test on a patient with
severe COPD. As the test progresses, the patient
shows signs of increasing dyspnea. - Measurements of inspiratory capacity decreased
from 2.0 L to 1.5 L. Which of the following most
likely occurred? - Dynamic hyperinflation
- Disconnected gas sampling line
5- Coronary blood flow
- Oxygen extraction.
- Answer C
- Buy Complete Questions Answers File from
- PDF Version Test Engine Software Version
- 90 Days Free Updates Service
- Valid for All Countries
http//www.exams4sure.com/NBRC/RPFT-practice-exam-
dumps.html