WHIRLPOOL DISHWASHER TROUBLESHOOTING - PARTSIPS

1
WHIRLPOOL DISHWASHER TROUBLESHOOTING PARTSIPS
2
(No Transcript)
3
Many of us depend on dishwashers to clean plates,
bowls, etc. with minimal hassle. Whirlpool is one
of the most popular and reliable manufacturers of
dishwashers. But, over the usage, Whirlpool
dishwashers have some common problems. If your
dishwasher is not draining, not turning on, not
cleaning, there is a need to fix them. It's
important to know how do you diagnose a
dishwasher problem and fix the problems to get
your appliance working in top order. To get the
details on Whirlpool dishwasher problems and
solutions, keep reading this blog. Low Cost on
all Whirlpool Dishwasher Parts, Order Bulk Spare
parts and get best discounts. Whirlpool
Dishwasher Troubleshooting Guide In this guide,
we focus on common problems with Whirlpool
dishwashers and their troubleshooting tips. So,
lets check them now! Whirlpool Dishwasher
Problems Dishes Not Clean A dishwasher not
cleaning dishes is the most common problem.
Specifically, the appliance fills with water, but
the wash pump does not circulate the water or run
the cycle. Mostly, this issue will occur with the
failure of the wash pump or motor. The failed
motor prevents the water from being propelled
throughout the spray arms so that the appliance
doesn't clean the dishes. The motor may fail
because of many reasons like a wiring fault
between the motor and control board or a
defective control board. So, first, check to
replace the wash pump if required. If there is a
defective motor or control board, you have to
replace them. Otherwise, removing the motor and
clean it as junk could build up around the motor
over time.
4
Dishes Not Drying Sometimes, your dishwasher may
not dry the dishes properly even after the cycle
has been completed. When the heating element is
damaged, the Whirlpool dishwasher doesn't dry the
dishes correctly. Generally, dishwashers use a
heating element and vent fan assembly to dry the
dishes. So, check if the heating element is burnt
out. Replace the defective heating
element. Start the replacement by accessing the
lower access panels at the bottom of the unit.
Disconnect the connectors which are going to the
heating element and remove the nuts that secure
the element. Later, open the dishwasher door and
pull out the heating element front. Place the
spray arm and pull it out of the appliance. Now,
you have to install the new heating element.
After that reassemble all the things. Dishwasher
Has No Lights or Not Responding If your
dishwasher is not responding or has no lights,
check for the problem of the thermal fuse. When
the thermal fuse is burned out on the control
board, the appliance doesn't respond. If the
thermal fuse is burnt, you need to buy a new
thermal fuse and install it. To replace, you
should unplug the dishwasher from the power
outlet and turn off the power supply. Remove the
screws and close the door. Now, you have to
remove the cover on the fuse. After that,
disconnect the wires with a screwdriver. Next,
cut off the terminal block and remove the tape
which holds the wire. Place the new thermal fuse
and re-tape the wires. Reassemble the fuse on the
control board and appliance.
5
Premium Quality Whirlpool Dishwasher Parts at low
Prices Order Now! Whirlpool Dishwasher Not
Draining Your dishwasher doesn't drain properly
if the impeller gets jammed by a broken piece of
glass or the drain pump fails. A broken impeller
prevents effective drainage. When the drain pump
is not working, the water will not move to the
drain line through the impeller. If there is no
possibility to repair, then you should replace
the drain pump. The drain solenoid is responsible
to open the drain valve to trigger water flow
from the appliance. So, when the drain valve is
not opened, water may collect. So, buy a new
drain solenoid kit and replace it. Check for
drain valves blocked. See if the valve has a
build up of debris, clean it. If no obstacles are
found in the drain line, check the motor. It
needs to be replaced if it is not
running. Dishwasher Wont Turn ON Check if the
control lock is on. If it is ON, your unit
doesn't start the action even after pressing the
start button. Unlock the control lock by the
press and hold the lock button for a minimum of 4
seconds. Next, inspect the sleep mode is ON. You
can deactivate the sleep mode by deactivating the
control lock. See if the Whirlpool dishwasher
door is not closed correctly. Ensure the door is
closed firmly. Verify whether there is water
supply turned on or not.
6
Dishwasher is Leaking Here some causes and
solutions for your dishwasher leaking
problem. Water inlet valve - This valve allows
water to enter the appliance. When the valve is
stuck in an open position, water will flow
continuously. So, check the valve position and
adjust it if it is stuck. You need to replace the
water valve if it is faulty. You have to check
the wash arms for cracks and splinters. If it is
broken, replace the arm. Finally, verify the unit
door seal that may allow water to flow out of the
unit. If the seal is damaged, you can see gaps so
that replace the seal quickly. Low Price on all
Whirlpool Appliance Parts Order
Now! Conclusion- Before you contact a
professional, it's a great idea to go through the
steps updated above and see if you can identify
possible causes for your Whirlpool dishwasher
issues. In most cases, you can buy new parts to
fix the problem. In order to order parts, check
out at partsips.com with a model number and get
it with home delivery service. Hopefully, this
Whirlpool dishwasher troubleshooting guide will
help you to find a solution quickly.
Click here to add the text
Your text has been concise and beautiful, but the
information is
7
Thank you
https//www.partsips.com/blog-whirlpool-dishwasher
-troubleshooting