Title: Caterpillar Cat 980M Wheel Loader (Prefix KRS) Service Repair Manual (KRS00001 and up)
1Service Repair Manual
Models 980M Wheel Loader
2Shutdown SIS
Previous Screen
Product WHEEL LOADER Model 980M WHEEL LOADER
KRS Configuration 980M Wheel Loader KRS00001-UP
(MACHINE) POWERED BY C13 Engine
Disassembly and Assembly 980M and 982M Wheel
Loaders Power Train Media Number
-UENR3097-03 Publication Date -01/09/2018
Date Updated -13/09/2018
i06838048
Torque Converter - Disassemble - Lock Up Clutch
With Freewheel Stator SMCS - 3101-015 Disassembly
Procedure Table 1 Required Tools
Tool Part Number Part Description Qty
A 439-3938 Link Bracket 3
8B-7548 Push-Puller 1
8B-7550 Leg 2
B 8H-0684 Ratchet Wrench 1
8B-7560 Step Plate 1
8H-0663 Bearing Puller Attachment 1
8B-7548 Push-Puller 1
8H-0684 Ratchet Wrench 1
C 8B-7549 Leg 2
5P-4808 Cap 2
8B-7554 Bearing Cup Puller Attachment 1
5F-7343 5F-7343 Bearing Puller Attachment 1
1P-0520 1P-0520 Driver Group 1
D
E 1P-0510 Driver Group 1
3F 6L-7283 Forcing Bolt 3/8 - 16 by 3 in 7
G 417-1324 Adjust Stand 1
Start By a. Separate the torque converter from
the transmission and from the output transfer
gears.
- Illustration 1 g02712129
- Use Tooling (A) and a suitable lifting device to
position the torque converter onto Tooling - (G) and suitable blocking. The weight of the
torque converter is approximately 260 kg (573
lb). Support the torque converter, as shown. - Remove bolts (1).
Illustration 2
g02730506
3. Remove relief valve assembly (2A).
4- Illustration 3 g02711758
- Use Tooling (F) to loosen housing assembly (2)
from the torque converter. - Use the suitable lifting device and Tooling (A)
to remove torque converter housing assembly (2).
The weight of torque converter housing assembly
(2) is approximately 144 kg (317 lb).
Illustration 4 g00871317 6. Remove O-ring seal
(3) from torque converter housing assembly (2).
Illustration 5
g00871318
57. Remove bolts (4) from pump adapter (5) and
torque converter housing assembly (2).
Illustration 6 g00871264 8. Use Tooling (F) to
remove pump adapter (5) from torque converter
housing assembly (2).
Illustration 7 g00871319 9. Use Tooling (B) to
remove bearing cup (6). Remove bearing cup (6),
O-ring seal (8), and shims (7) from pump adapter
(5). See illustration 14 for Tooling (C).
Illustration 8 g00871326 10. Remove pump drive
gear (9) from torque converter housing assembly
(2).
6https//www.aservicemanualpdf.com/ My Dear
Friend! Thank you very much for visiting. Full
manual if required, please enter the following
URL into your browser. https//www.aservicemanual
pdf.com/
7Illustration 9 g00871451 11. Use Tooling (C) to
remove bearing cones (10) from each side of pump
drive gear (9). Remove bearing cones (10).
Illustration 10 g00871333 12. Use Tooling (C) to
remove bearing cup (11) from torque converter
housing assembly (2). See illustration 14 for
Tooling (C).
Illustration 11 g01112900 13. Remove bolt (12)
and the washer from torque converter housing
assembly (2).
8- Use Tooling (F) to push shaft assembly (14) out
of torque converter housing assembly (2). - Remove idler gear (13) from torque converter
housing assembly (2).
Illustration 12 g01112903 16. Remove O-ring seal
(15) from shaft assembly (14).
Illustration 13 g00871365 17. Remove bearing
cone (16), bearing cone spacer (17), and bearing
cone (18) from idler gear (13).
9Illustration 14 g00871366 18. Use Tooling (C) to
remove bearing cup (19) from idler gear (13).
Remove bearing cup (19).
Illustration 15 g00871367 19. Remove bearing cup
spacer (20) from idler gear (13).
Illustration 16
g00871368
1020. Remove retaining ring (21) from idler gear
(13).
Illustration 17 g00871369 21. Use Tooling (C) to
remove bearing cup (22) from idler gear (13).
Remove bearing cup (22).
Illustration 18 g00871370 22. Remove studs (23)
from torque converter housing assembly (2).
11Illustration 19
g02729366
23. Remove bolts (24) and gear (25).
Illustration 20 g02735357 24. Use the driver
group from Tooling (D) and a suitable press to
remove race (25A) from gear (25).
Illustration 21 g02730012 25. Use a suitable
lifting device to reposition the torque
converter, as shown. The weight of the torque
converter is approximately 122 kg (269 lb).
Remove bolts (26).
12Illustration 22 g02730687 26. Use Tooling (F) to
separate housing (27) from the torque converter.
Illustration 23 g02730689 27. Use two people to
remove housing (27). The weight of housing (27)
is approximately 26 kg (57 lb). Remove housing
(27), piston (28), and plate (30). Remove seals
(29) from piston (28).
Illustration 24
g02731059
28. Remove bushing (31) from housing (27).
13Illustration 25 g02731623 29. Remove plate (32),
disk (33), races (34), and bearing (35). Note
Note the orientation of the bearing and races for
assembly purposes.
Illustration 26 g02731644 30. Remove bolts (36),
coupling assembly (37), and plate (38).
14Illustration 27 g02731651 31. Use suitable
blocking to support the bottom of shaft assembly
(39). Remove retaining ring (40) and plate (41).
Shaft assembly (39) can be lowered to the work
bench.
Illustration 28
g02731711
Illustration 29
g02732048
15- Install two of bolts (36) and remove turbine
(42). - Remove bolts (36) and remove hub (43) from
turbine (42).
Illustration 30
g02731732
Illustration 31
g02731802
- Remove race (44) and bearing (45).
- Note Note the orientation of the race and
bearing for assembly purposes. - Remove stator assembly (46).
16Illustration 32 g02731806 36. Remove retaining
ring (47), plate (48), freewheel springs (49),
freewheel rollers (50), and freewheel cam (51).
Remove plate (52) and retaining ring (53) (not
shown) from stator (46).
- Illustration 33 g02732255
- Attach Tooling (A) and a suitable lifting device
to impeller (54). The weightof impeller (54) is
approximately 27 kg (60 lb). - Remove impeller (54) from shaft assembly (39).
Illustration 34 g02735333 39. Position impeller
(54) onto suitable blocking, as shown.
17Illustration 35
g02734776
40. Remove retaining ring (56) and hub (55).
Illustration 36
g02735372
41. Remove seal ring (56).
Illustration 37 g02734816 42. Use Tooling (D)
and a suitable press to remove bearing (57).
Illustration 38
g02735374
1843. Remove retaining ring (59) and carrier
assembly (58) from impeller (54).
Illustration 39
g02735380
44. Remove bearing (60). Note Note the
orientation of the bearing (60) for assembly
purposes.
Illustration 40 g02735387 45. Remove bolts (61),
hub (62), and adapter (63) from impeller (54).
19Illustration 41
g02752296
46. Remove seals (64).
Copyright 1993 - 2021 Caterpillar Inc. All Rights
Reserved. Private Network For SIS Licensees.
Thu Mar 18 223938 UTC0800 2021
20Shutdown SIS
Previous Screen
Product WHEEL LOADER Model 980M WHEEL LOADER
KRS Configuration 980M Wheel Loader KRS00001-UP
(MACHINE) POWERED BY C13 Engine
Disassembly and Assembly 980M and 982M Wheel
Loaders Power Train Media Number
-UENR3097-03 Publication Date -01/09/2018
Date Updated -13/09/2018
i06838485
Torque Converter - Assemble - Lock Up Clutch with
Freewheel Stator SMCS - 3101-016 Assembly
Procedure Table 1
Required Tools Required Tools Required Tools Required Tools
Tool Part Number Part Description Qty
A 439-3938 Link Bracket 3
G 8T-5096 Dial Indicator Test Group 1
G 5P-2390 Gauge Tool Group 1
H 1P-0520 Driver Group 1
J - Guide Stud (3/8 - 16 by 8 in) 2
K - Guide Stud (1/2 - 13 by 3 in) 3
L 2P-8312 Retaining Ring Pliers 1
21Illustration 1
g02752296
1. Install seals (64).
Illustration 2 g02735387 2. Install adapter
(63), hub (62), and bolts (61) onto impeller
(54). Tighten bolts (61) to a torque of 105 14
Nm (77 10 lb ft).
Illustration 3
g02735380
3. Install bearing (60).
22Illustration 4 g02735374 4. Install carrier
assembly (58) and retaining ring (59) onto
impeller (54).
- Illustration 5 g02744677
- Raise the temperature of bearing (57). Install
bearing (57) onto hub (55). - Install seal ring (56).
Illustration 6
g02734776
23Illustration 7 g02735333 7. Install hub (55) and
retaining ring (56) onto impeller (54).
- Illustration 8 g02732255
- Attach Tooling (A) and a suitable lifting device
to impeller (54). The weight of impeller - (54) is approximately 27 kg (60 lb).
- Position impeller (54) onto shaft assembly (39).
Illustration 9 g02731806 10. Install retaining
ring (53) (not shown) and plate (52) onto stator
(46).
24- Install freewheel cam (51), freewheel rollers
(50), and springs (49). - Note Springs (49) must be installed with the
maximum number or loops to the outside. - Install plate (48) and retaining ring (47).
Illustration 10
g02731802
Illustration 11
g02731732
- Install stator assembly (46).
- Install bearing (45) and race (44).
25Illustration 12
g02744699
Illustration 13
g02731651
- Install hub (43) and turbine (42).
- Use two of bolts (36) to align the holes.
- Use suitable blocking to support the bottom of
shaft assembly (39). Install plate (41) and
retaining ring (40).
Illustration 14 g02731644 18. Install plate
(38), coupling assembly (37), and bolts (36).
Tighten bolts (36) to a torque of 60 7 Nm (44
5 lb ft).
26Illustration 15 g02731623 19. Install plate
(32), disk (33), races (34), and bearing (35).
Illustration 16 g02731059 20. Lower the
temperature of bushing (31). Install bushing (31)
into housing (27).
27Illustration 17 g02730689 21. Install seals (29)
onto piston (28). Install plate (30), piston
(28), and housing (27).
Illustration 18 g02730012 22. Install bolts
(26). Tighten bolts (26) to a torque of 60 7
Nm (44 5 lb ft).
Illustration 19
g02735357
2823. Lower the temperature of race (25A). If
necessary, use the driver group from Tooling (D)
and a suitable press to install race (25A) into
gear (25).
- Illustration 20 g02729366
- Use a suitable lifting device to reposition the
torque converter, as shown. The weight of the
torque converter is approximately 122 kg (269
lb). - Install drive gear (25) and bolts (24). Tighten
the bolts to a torque of 50 7 Nm (37 5 lb
ft).
Illustration 21 g00872709 26. Install studs (23)
in torque converter housing assembly (2). Tighten
the studs to a torque of 100 15 Nm (74 11 lb
ft).
29Illustration 22 g00872711 27. Install retaining
ring (21) in the groove of idler gear (13).
Illustration 23 g00872713 28. Use the proper
equipment to handle bearing cup (22). Lower the
temperature of bearing cup (22). Install bearing
cup (22) in idler gear (13).
Illustration 24 g00872715 29. Flip idler gear
(13) to the opposite side. Install bearing cup
spacer (20) in idler gear (13). The notch in
bearing cup spacer (20) must be aligned with
retaining ring (21).
30Illustration 25 g00872716 30. Use the proper
equipment to handle bearing cup (19). Lower the
temperature of bearing cup (19). Install bearing
cup (19) in idler gear (13).
Illustration 26 g00872718 31. Install bearing
cone (16), bearing cone spacer (17), and bearing
cone (18) in idler gear (13).
Illustration 27 g01112903 32. Apply clean
hydraulic oil on O-ring seal (15). Install O-ring
seal (15) on shaft assembly (14).
31- Illustration 28 g01112954
- Install Tooling (K) in shaft assembly (14).
- Hold idler gear (13) in position in torque
converter housing assembly (2). Install shaft
assembly (14). - Remove Tooling (K) from shaft assembly (14).
Illustration 29 g01112970 36. Install bolt (12)
that holds shaft assembly (14) in place in torque
converter housing assembly (2). Tighten bolt (12)
to a torque of 120 20 Nm (90 15 lb ft).
Illustration 30 g00872724 37. Use the proper
equipment to handle bearing cones (10). Heat
bearing cones to a maximum temperature of 135 C
(275 F). Install bearing cone (10) on each side
of pump drive gear (9).
32Illustration 31 g00872801 38. Use the proper
equipment to handle bearing cup (11). Lower the
temperature of bearing cup (11). Install bearing
cup (11) in torque converter housing assembly (2).
Illustration 32 g00872727 39. Install pump drive
gear (9) in torque converter housing assembly (2).
Illustration 33 g00872729 40. Use the proper
equipment to handle bearing cup (6). Lower the
temperature of bearing cup (6).
33Thank you very much for your reading.
Please Click Here. Then Get COMPLETE MANUAL. NO
WAITING
GET MORE OTHER MANUALS
https//www.aservicemanualpdf.com/
- NOTE
- If there is no response to click on the link
above, please download the PDF document first
and then click on it.
GET MORE OTHER MANUALS
https//www.aservicemanualpdf.com/
34- Illustration 34 g00871319
- Apply clean hydraulic oil on O-ring seal (8).
- Install bearing cup (6), O-ring seal (8), and
shims (7) on pump adapter (5).
- Illustration 35 g01112978
- Install Tooling (J) in torque converter housing
assembly (2). - Install pump adapter (5) on torque converter
housing assembly (2).
Illustration 36
g01112982
35- Install bolts (4) and the washers on pump adapter
(5) and torque converter housing assembly (2). - Use Tooling (G) to check bearing end play. The
bearing end play must be 0.15 0.05 mm (0.006
0.002 inch). Add or remove shims to get the
correct bearing end play. - Note If end play is less than 0.10 mm (0.004
inch) add extra shims. If end play is greater
than 0.20 mm (0.008 inch) remove shims.
Illustration 37 g00872732 47. Apply clean
hydraulic oil on O-ring seal (3). Install O-ring
seal (3) on torque converter housing assembly (2).
Illustration 38
g02730506
48. Install relief valve assembly (2A).
36Illustration 39
g02752336
- Illustration 40 g02752337
- Install Tooling (J) in the carrier assembly.
- Use Tooling (A) and a suitable lifting devise to
position torque converter housing assembly - (2) to position torque converter housing assembly
(2) on the torque converter, as shown. The weight
of torque converter housing assembly (2) is
approximately 144 kg (317 lb). Install two bolts
(1).
Illustration 41
g00503225
37https//www.aservicemanualpdf.com/ My Dear
Friend! Thank you very much for visiting. Full
manual if required, please enter the following
URL into your browser. https//www.aservicemanual
pdf.com/