ECET 402 Course Inspiring Minds / tutorialrank.com

1
ECET 402 Course Inspiring Minds/ tutorialrank.com
The Best way to predict the Future is to create
it.....To Best way....
www.tutorialrank.com
2
ECET 402 Course Inspiring Minds/ tutorialrank.com
ECET 402 Week 1 Homework
ECET 402 HW Week 1 Pages 20-21 2,4,6,11,14 CH
3pgs103 4,6
3
ECET 402 Course Inspiring Minds/ tutorialrank.com
ECET 402 Week 1 iLab
1.From Part A, step 1(b) of lab instructions,
change the temperature from 0 to 30 C and record
the corresponding RTD resistance in Table
1. 2.Graph the temperature-resistance
characteristics of RTD below 3.Is the graph
obtained in step 2 above linear (a straight
line)? 4.Use the graph obtained in step 2 above
to determine the resistance of RTD at 75 F.
4
ECET 402 Course Inspiring Minds/ tutorialrank.com
ECET 402 Week 2 Homework
Chapter 3 Page 104-105 Problems 24, 25, 28, 30,
and 38
5
ECET 402 Course Inspiring Minds/ tutorialrank.com
ECET 402 Week 2 iLab
1.After completing Part A of week 2 lab, complete
the following table 2.Briefly describe if you
had any issues with this lab. 3.Briefly describe
how you would display the temperature on the LCD
display of a microcontroller system. 4.From Part
B, step 1 of lab instructions, paste your
Multisim circuit design below. 5.From Part B,
step 2 of lab instructions, paste your Multisim
circuit design below. 6.Enter IL and VL values
you found in the circuit of Figure 5 of lab
instructions below
6
ECET 402 Course Inspiring Minds/ tutorialrank.com
ECET 402 Week 3 Homework
Homework 1. What is the difference between
static,sliding, and viscous friction? 2. An
aluminum casting that weighs 10 lb is resting on
a steel surface. 6.A robot arm must be able to
extend 24 in. horizontally in 2 s while carrying
a load of 10 lb. How much force is required,
assuming the arm is accelerating all the
way? 14.A torque of 18 N m is applied to a
rotating part. The part has a moment of inertia
of 0.078 kg m2. How much time will it take to
rotate the part 180? 19.An electric heater is
rated at 220 Vac at 15 A. How many Btu/h of heat
does it put out?
7
ECET 402 Course Inspiring Minds/ tutorialrank.com
ECET 402 Week 3 iLab
Part A Voltage to Frequency Converter 1.Change
input voltage from 210 volts and record measured
frequency in Table 1 2. Use the data obtained in
Table 1 to graph Frequency vs. Voltage in Figure
1. 3.Is the output frequency vs. voltage graph
linear? 4.Research and describe some applications
for Voltage to Frequency Converter circuits. Part
B The Security Alarm System
8
ECET 402 Course Inspiring Minds/ tutorialrank.com
ECET 402 Week 4 Homework
Week 4 Homework Chapter 11 pp. 483488, Problems
1, 2, 6, 8, 12, 13, and 19 1.Assume that Figure
11.25(a) is the response curve of a control
system to a step function. Determine the
following parameters rise time, overshoot, and
settling time.
9
ECET 402 Course Inspiring Minds/ tutorialrank.com
ECET 402 Week 4 iLab Relays and Relay Logic
Controls
ECET 402 Week 4 iLab Relays and Relay Logic
Controls
10
ECET 402 Course Inspiring Minds/ tutorialrank.com
ECET 402 Week 5 Homework
Chapter 12 1. Draw a relay wiring diagram for a
circuit that implements the simple logic diagram
shown in Figure 12.36. The circuit should be in
the style of Figure 12.1(a). 2. Repeat Exercise 1
except draw the circuit as a ladder diagram. 3. A
small house has three windows and two doors. Each
window and door has a switch attached such that
the contacts close when a door or window opens.
Draw a ladder logic diagram that will turn on a
light if one or more windows are open or if both
doors are open.
11
ECET 402 Course Inspiring Minds/ tutorialrank.com
ECET 402 Week 5 iLab Stepper Motor and Measuring
Speed of a DC Motor
Part A Take a digital photo of your stepper
motor circuit and paste it below Once the
assembly of stepper motor circuit is completed
and power is applied, observe the direction of
rotation and record it here
12
ECET 402 Course Inspiring Minds/ tutorialrank.com
ECET 402 Week 6 Homework
P.405, 1Give an example of an open-loop control
system. Explain why the system is open-loop, and
identify the controller and final control
element. P.405, 2Give an example of a
closed-loop control system. Explain why the
system is closed-loop, and identify the sensor,
controller, and final control element. P.405,
7Describe the advantages of a 4- to 20-mA
current loop as an input signal compared to a
0-to 5-V input signal. P.435, 2Complete a report
on one type of open communications network. Make
use of the Internet as well as manufacturer's
literature for compiling the report.
13
ECET 402 Course Inspiring Minds/ tutorialrank.com
ECET 402 Week 6 iLab
1. Determine the overall transfer function of the
system given below by hand as discussed in
pre-lab. Please show your work and type the
equations if you can 2. Determine the overall
transfer function of the system shown above using
MATLAB. Copy the MATLAB code and the overall
transfer function obtained and paste them
below 3. Are the results in steps 1 and 2 the
same? Comment if they are not. 4.Determine the
unit step response of the overall system using
the MATLAB comman
14
ECET 402 Course Inspiring Minds/ tutorialrank.com
ECET 402 Week 7 iLab Root Locus Plots and the
Stability of a Control System
ECET 402 Week 7 iLab Root Locus Plots and the
Stability of a Control System
15
ECET 402 Course Inspiring Minds/ tutorialrank.com
The Best way to predict the Future is to create
it.....To Best way....
www.tutorialrank.com