ECET 402 Dreams Come True /newtonhelp.com

1
ECET 402 Dreams Come True /newtonhelp.com
2
ECET 402 Week 1 Homework 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• ECET 402 HW Week 1
• Pages 20-21 2,4,6,11,14
• CH 3pgs103 4,6
•  

3
ECET 402 Week 1 iLab 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• .From Part A, step 1(b) of lab instructions,
  change the temperature from 0 to 30 C and record
  the corresponding RTD resistance in Table 1.
• 2.Graph the temperature-resistance
  characteristics of RTD below
• 3.Is the graph obtained in step 2 above linear (a
  straight line)?

4
ECET 402 Week 2 Homework 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
•  
• Chapter 3
• Page 104-105 Problems 24, 25, 28, 30, and 38

5
ECET 402 Week 2 iLab 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• 1.After completing Part A of week 2 lab, complete
  the following table
• 2.Briefly describe if you had any issues with
  this lab.
• 3.Briefly describe how you would display the
  temperature on the LCD display of a
  microcontroller system.

6
ECET 402 Week 3 Homework

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• Homework
• 1. What is the difference between
  static,sliding, and viscous friction?
• 2. An aluminum casting that weighs 10 lb is
  resting on a steel surface.
• 6.A robot arm must be able to extend 24 in.
  horizontally in 2 s while carrying a load of 10
  lb. How much force is required, assuming the arm
  is accelerating all the way?

7
ECET 402 Week 3 iLab 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• Part A Voltage to Frequency Converter
• 1.Change input voltage from 210 volts and record
  measured frequency in Table 1
• 2. Use the data obtained in Table 1 to graph
  Frequency vs. Voltage in Figure 1.
• 3.Is the output frequency vs. voltage graph
  linear?

8
ECET 402 Week 4 Homework

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• Week 4 Homework
• Chapter 11 pp. 483488, Problems 1, 2, 6, 8, 12,
  13, and 19
• 1.Assume that Figure 11.25(a) is the response
  curve of a control system to a step function.
  Determine the following parameters rise time,
  overshoot, and settling time.
•  

9
ECET 402 Week 4 iLab Relays and Relay Logic
Controls 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• ECET 402 Week 4 iLab Relays and Relay Logic
  Controls
•  

10
ECET 402 Week 5 Homework

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• Chapter 12
• 1. Draw a relay wiring diagram for a circuit that
  implements the simple logic diagram shown in
  Figure 12.36. The circuit should be in the style
  of Figure 12.1(a).
• 2. Repeat Exercise 1 except draw the circuit as a
  ladder diagram.

11
ECET 402 Week 5 iLab Stepper Motor and Measuring
Speed of a DC Motor

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• Part A
• Take a digital photo of your stepper motor
  circuit and paste it below
• Once the assembly of stepper motor circuit is
  completed and power is applied, observe the
  direction of rotation and record it here

12
ECET 402 Week 6 Homework 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• P.405, 1Give an example of an open-loop control
  system. Explain why the system is open-loop, and
  identify the controller and final control
  element.
• P.405, 2Give an example of a closed-loop control
  system. Explain why the system is closed-loop,
  and identify the sensor, controller, and final
  control element.

13
ECET 402 Week 6 iLab 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• . Determine the overall transfer function of the
  system given below by hand as discussed in
  pre-lab. Please show your work and type the
  equations if you can
• 2. Determine the overall transfer function of the
  system shown above using MATLAB. Copy the MATLAB
  code and the overall transfer function obtained
  and paste them below
• 3. Are the results in steps 1 and 2 the same?
  Comment if they are not.

14
ECET 402 Week 7 iLab Root Locus Plots and the
Stability of a Control System 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
•  
• ECET 402 Week 7 iLab Root Locus Plots and the
  Stability of a Control System
•  
•  

15
ECET 402 Dreams Come True /newtonhelp.com