Cisco CCNP 300 115 SWITCH dumps - PowerPoint PPT Presentation

About This Presentation
Title:

Cisco CCNP 300 115 SWITCH dumps

Description:

To help you prepare CCNP certification 300-115 exam, Passcert recommends you that you should have the sound knowledge and experience about 300-115 SWITCH exam. Passcert has designed Cisco CCNP 300-115 SWITCH dumps to help you get certified easily. With Cisco CCNP 300-115 SWITCH dumps from Passcert you can pass your exam easily and get on your path for success. – PowerPoint PPT presentation

Number of Views:44

less

Transcript and Presenter's Notes

Title: Cisco CCNP 300 115 SWITCH dumps


1
300-115 SWITCH
  • Implementing Cisco IP Switched Networks

https//www.passcert.com/300-115.html
2
  • 300-115 Sample Questions From Real Test

Back to school
https//www.passcert.com/300-115.html
3
  • 1. A network engineer wants to add a new switch
    to an existing switch stack.
  • Which configuration must be added to the new
    switch before it can be added to the switch
    stack?
  • A. No configuration must be added.
  • B. stack ID
  • C. IP address
  • D. VLAN information
  • E. VTP information
  • Answer A

https//www.passcert.com/300-115.html
4
  • 2. After an EtherChannel is configured between
    two Cisco switches, interface port channel 1 is
    in the
  • down/ down state. Switch A is configured with
    channel-group 1 mode active, while Switch B is
    configured
  • with channel-group 1 mode desirable.
  • Why is the EtherChannel bundle not working?
  • A. The switches are using mismatched EtherChannel
    negotiation modes.
  • B. The switch ports are not configured in
    trunking mode.
  • C. LACP priority must be configured on both
    switches.
  • D. The channel group identifier must be different
    for Switch A and Switch B.
  • Answer A

https//www.passcert.com/300-115.html
5
  • 3. An EtherChannel bundle has been established
    between a Cisco switch and a corporate web
    server.
  • The network administrator noticed that only one
    of the EtherChannel links is being utilized to
    reach the
  • web server.
  • What should be done on the Cisco switch to allow
    for better EtherChannel utilization to the
    corporate web
  • server?
  • A. Enable Cisco Express Forwarding to allow for
    more effective traffic sharing over the
    EtherChannel
  • bundle.
  • B. Adjust the EtherChannel load-balancing method
    based on destination IP addresses.
  • C. Disable spanning tree on all interfaces that
    are participating in the EtherChannel bundle.
  • D. Use link-state tracking to allow for improved
    load balancing of traffic upon link failure to
    the server.
  • E. Adjust the EtherChannel load-balancing method
    based on source IP addresses.
  • Answer E

https//www.passcert.com/300-115.html
6
  • 4. Interface FastEthernet0/1 is configured as a
    trunk interface that allows all VLANs. This
    command is
  • configured globally monitor session 2 filter
    vlan 1 - 8, 39, 52 What is the result of the
    implemented
  • command?
  • A. All VLAN traffic is sent to the SPAN
    destination interface.
  • B. Traffic from VLAN 4 is not sent to the SPAN
    destination interface.
  • C. Filtering a trunked SPAN port effectively
    disables SPAN operations for all VLANs.
  • D. The trunk's native VLAN must be changed to
    something other than VLAN 1.
  • E. Traffic from VLANs 1 to 8, 39, and 52 is
    replicated to the SPAN destination port.
  • Answer E

https//www.passcert.com/300-115.html
7
  • 5. A network engineer notices inconsistent Cisco
    Discovery Protocol neighbors according to the
    diagram
  • that is provided. The engineer notices only a
    single neighbor that uses Cisco Discovery
    Protocol, but it
  • has several routing neighbor relationships.
  • What would cause the output to show only the
    single neighbor?
  • A. The routers are connected via a Layer 2
    switch.
  • B. IP routing is disabled on neighboring devices.
  • C. Cisco Express Forwarding is enabled locally.
  • D. Cisco Discovery Protocol advertisements are
    inconsistent between the local and remote
    devices.
  • Answer A

https//www.passcert.com/300-115.html
8
  • 6. After the implementation of several different
    types of switches from different vendors, a
    network
  • engineer notices that directly connected devices
    that use Cisco Discovery Protocol are not
    visible.
  • Which vendor-neutral protocol could be used to
    resolve this issue?
  • The safer , easier way to help you pass any IT
    exams.
  • 8 / 208
  • A. Local Area Mobility
  • B. Link Layer Discovery Protocol
  • C. NetFlow
  • D. Directed Response Protocol
  • Answer B

https//www.passcert.com/300-115.html
9
  • 7. Which three functions dose Dynamic ARP
    Inspection perform with invalid IP-to MAC address
  • bindings? (choose three)
  • A. logs
  • B. deletes
  • C. intercepts
  • D. accepts
  • E. discads
  • F. bypasses
  • Answer ACE

https//www.passcert.com/300-115.html
10
  • 8. Which statement is true about RSTP topology
    changes?
  • A. Any change in the state of the port generates
    a TC BDPU
  • B. Only nonedge ports moving to the forwarding
    state generate a TC BDPU
  • C. If either an edge port or a nonedge port move
    to a block state, then a TC BDPU is generated
  • D. Only edge ports moving to the blocking state
    generate a TC BPDU E. Any loss of connectivity
  • generates a TC BDPU
  • Answer B

https//www.passcert.com/300-115.html
11
  • 9. What action should a network admin take to
    enable VTP pruning on an entire management
    domain?
  • A. Enable VTP pruning on any client switch in the
    domain.
  • B. Enable VTP pruning on every switch in the
    domain.
  • C. Enable VTP pruning on any switch in the
    management domain
  • D. Enable VTP pruning on a VTP server in the
    management domain.
  • Answer D

https//www.passcert.com/300-115.html
12
  • 10. Which two statements are true about
    recommended practices that are to be used in a
    local VLAN
  • solution design where layer 2 traffic is to be
    kept to a minimum? (Choose two)
  • A. Routing should occur at the access layer if
    voice VLANs is utilized. Otherwise, routing
    should occur at
  • the distributionlayer.
  • B. Routing may be performed at all layers but is
    most commonly done at the core and distribution
    layers
  • C. Routing should not be performed between VLANs
    located on separate switches
  • D. Vlans should be local to a Switch
  • E. Vlans should ne localized to a single switch
    unless voice VLANs are being utilized
  • Answer BD

https//www.passcert.com/300-115.html
13
PPT????www.1ppt.com/moban/
??PPT??www.1ppt.com/hangye/ ??PPT??www.1ppt.com
/jieri/ PPT????www.1ppt.com/sucai/ PPT?
???www.1ppt.com/beijing/ PPT????www.1ppt.co
m/tubiao/ ??PPT??www.1ppt.com/xiazai/
PPT?? www.1ppt.com/powerpoint/ Word??
www.1ppt.com/word/
Excel??www.1ppt.com/excel/ ????www.1ppt.com/zi
liao/ PPT????www.1ppt.com/kejian/
????www.1ppt.com/fanwen/
????www.1ppt.com/shiti/ ????www.1ppt.com/jiaoa
n/
https//www.passcert.com/300-115.html
Write a Comment
User Comments (0)
About PowerShow.com