ECET 110 Technology levels--snaptutorial.com

1
ECET 110 Technology levels--snaptutorial.com
2
ECET 110 Technology levels--snaptutorial.com
ECET 110 Quiz 2 For more classes
visit www.snaptutorial.com   1. (TCO 4) For the
series-parallel circuit given in Figure 3.1
below, determine the total resistance RT between
the terminals labeled A and B 2. (TCO 4) For the
circuit given in Figure 3.3, obtain the following
quantities.
3
ECET 110 Technology levels--snaptutorial.com
ECET 110 Quiz 3 For more classes
visit www.snaptutorial.com   1. (TCO 7) For the
circuit given below, determine the total
capacitance CT between the terminals labeled A
and B.
4
ECET 110 Technology levels--snaptutorial.com
ECET 110 Week 1 Homework For more classes
visit www.snaptutorial.com   Why do you never
apply an ohmmeter to a live network? What is the
voltage across a 220 ? resistor if the current
through it is 5.6 mA?
5
ECET 110 Technology levels--snaptutorial.com
ECET 110 Week 1 iLab Analysis of a Series Circuit
using Simulation and Actual Construction For
more classes visit www.snaptutorial.com   Objectiv
es To construct a circuit in series to test and
verify Ohms Law and Kirchhoffs Voltage Law
using a multi-meter, breadboard, resistors and
jumper wires. To simulate this construct
digitally and mathematically to compare results
to determine if the above laws are supported.
6
ECET 110 Technology levels--snaptutorial.com
ECET 110 Week 2 Homework For more classes
visit www.snaptutorial.com   CHAPTER 6 4. For
each circuit board in Fig. 6.74, find the total
resistance between connection tabs 1 and 2. 10.
For the network of Fig. 6.80
7
ECET 110 Technology levels--snaptutorial.com
ECET 110 Week 2 iLab Analysis of a DC Parallel
Circuit using Simulation and Actual Construction
For more classes visit www.snaptutorial.com   Obj
ectives The objectives this week were to
effectively learn to simulate and construct a
parallel circuit and learn to troubleshoot issues
that may be had by OPEN or Shorted circuits.
Also to learn how to calculate current and
resistance within parallel circuits
8
ECET 110 Technology levels--snaptutorial.com
ECET 110 Week 2 Quiz For more classes
visit www.snaptutorial.com   1. (TCO 3) Find the
total conductance and total resistance of the
parallel circuit given below. 2. (TCO 3) A
resistor in one of the parallel branches is
replaced by a short circuit as shown in the
figure below. Determine the current IS through
this shorted branch.
9
ECET 110 Technology levels--snaptutorial.com
ECET 110 Week 3 Homework For more classes
visit www.snaptutorial.com   Chapter 7 Problems
1 (a, b, c), 2 (a, b), 3, 8, 10 1. Which elements
(individual elements, not combinations of
elements) of the networks in Fig. 7.60 are in
series? Which are in parallel? As a check on your
assumptions, be sure that the elements in series
have the
10
ECET 110 Technology levels--snaptutorial.com
ECET 110 Week 3 iLab Analysis of a DC
Series-Parallel Circuit For more classes
visit www.snaptutorial.com   Objectives To
construct a series-parallel circuit correctly and
measure its equivalent resistance.
11
ECET 110 Technology levels--snaptutorial.com
ECET 110 Week 4 Homework For more classes
visit www.snaptutorial.com   Objectives 1. To
troubleshoot a complex circuit and determine
various currents and voltages using format mesh
analysis. 2. To simulate the complex circuit in
MultiSim and record the required quantities.
12
ECET 110 Technology levels--snaptutorial.com
ECET 110 Week 4 iLab Format Mesh Analysis For
more classes visit www.snaptutorial.com   Objectiv
es 1. To troubleshoot a complex circuit and
determine various currents and voltages using
format mesh analysis. 2. To simulate the complex
circuit in MultiSim and record the required
quantities. 3. Determine the various currents and
voltages after wiring the circuit. Results The
results were as predicted.
13
ECET 110 Technology levels--snaptutorial.com
ECET 110 Week 5 Homework For more classes
visit www.snaptutorial.com   CHAPTER 9 1a. Using
the superposition theorem, determine the current
through the 12 Ohm resistor of fig. 9.119. we
will use superposition to analyze this circuit.
First short E2 and find the current thru the 12
Ohms resistor and then Short E1 and keep E2 in
the circuit and find the same current. Then
algebraically add the two currents (add if in the
same directions and subtract if opposite direction
14
ECET 110 Technology levels--snaptutorial.com
ECET 110 Week 5 iLab Thevenins and Superposition
Theorem For more classes visit www.snaptutorial.
com   Objectives 1. To troubleshoot a complex
circuit and determine various currents and
voltages using superposition theorem and compare
the results with the results of last weeks lab.
15
ECET 110 Technology levels--snaptutorial.com
ECET 110 Week 6 Homework Capacitors For more
classes visit www.snaptutorial.com     Chapter
10 Capacitors 20. Repeat Problem 19 for R 1
MO, and compare the results 26. For the network
in Fig. 10.98, composed of standard values 34.
For the automobile circuit of Fig. 10.105, VL
must be 8 V before the system is activated. If
the switch is closed at t 0 s, how long will it
take for the system to be activated?
16
ECET 110 Technology levels--snaptutorial.com
ECET 110 Week 6 iLab Transient Analysis of a
Resistor-Inductor Circuit For more classes
visit www.snaptutorial.com     1.
OBJECTIVES Perform a transient analysis on a
Resistor-Capacitor circuit, and measure capacitor
charge
17
ECET 110 Technology levels--snaptutorial.com
ECET 110 Week 6 Quiz For more classes
visit www.snaptutorial.com     1. (TCO 7) For the
circuit given below, determine the total
capacitance CT between the terminals labeled A
and B
18
ECET 110 Technology levels--snaptutorial.com
ECET 110 Week 7 Homework For more classes
visit www.snaptutorial.com     Chapter 11
Inductors Homework problems 12, 14, 29, 36
19
ECET 110 Technology levels--snaptutorial.com
ECET 110 Week 7 iLab Transient Analysis of a
Resistor-Inductor Circuit For more classes
visit www.snaptutorial.com     Objectives Calcula
te time constant, transient time, current and
voltage across inductor at beginning and the end
of the charge cycle. Use MultiSim to test the
calculations. Build and test a physical circuit
using the MultiSim schematic.
20
ECET 110 Technology levels--snaptutorial.com