200-301 VOL3 Question

1
200-301 Cisco Certified Network Associate (CCNA)
VOL3 QUESTION NO 1 You want to implement RFC
3021 to assign an IP address to router R1 on a
point-to-point link. Which of the following is a
viable option for this?
A. B. C. D.
10.10.1.185/30 10.2.2.1 255.255.255.252 10.1.0.1/3
1 10.2.2.5 255.255.255.255
Answer C

• QUESTION NO 2
• IPv6 addressing is being implemented in a new
  network. Which of the following is NOT a valid
  IPv6 address type that can be implemented on this
  network?
• Unicast
• Multicast
• Anycast
• Broadcast
• Answer D

• QUESTION NO 3
• A network administrator has configured the same
  IPv6 address to a set of servers that are
  geographically dispersed in order to enhance the
  uptime of the application and to provide a
  better response time for end users. What is this
  an example of?
• IPv6 Unicast routing
• IPv6 Anycast
• IPV6 Multicast
• IPv6 Broadcast
• Answer B

QUESTION NO 4
2

• You need to implement and manage a wireless
  network consisting of approximately 150 access
  points and thousands of clients. Which of the
  following would be the most helpful in the
  configuration and management of the access points
  in this network?
• SNMP server
• WLC
• Netflow
• REST APIs
• Answer B

• QUESTION NO 5
• With NTP, A stratum 2 device synchronizes its
  time to what other type of NTP device?
• Stratum 0 Time Server
• Stratum 1 Time Server
• Stratum 2 Time Server
• Stratum 3 Time Server
• Answer C

• QUESTION NO 6
• You have booted a new IPV6 capable device on the
  network and discovered that this device has an
  IPv6 address configured on it by choosing its own
  IPv6 address based on the IPv6 prefix that is
  advertised by the connected IPV6 enabled router.
  What is this an example of?
• SLAAC
• EUI-64 bit addressing
• DHCPv6
• Dual stack
• Answer A

• QUESTION NO 7
• Which of the following are used to terminate
  Cat6e cabling in a computer network?
• BNC
• LC
• RJ-45
• SC

3
Answer C

• QUESTION NO 8
• The IPV6 address of FE801144aa11 is an example
  of which type of address?
• EUI-64
• Anycast
• Broadcast
• Link local
• Answer D

• QUESTION NO 9
• A new network has the following remote offices
• Site 1 has 12 users
• Site 2 has 135 users.
• Site three has 350 users
• You have been tasked with assigning a subnet for
  each of these locations using the private
  10.10.0.0/8 subnet. Which of the following
  addressing schemes should be used to ensure the
  least amount of addressing waste, while ensuring
  no subnets overlap?
• A. 10.10.0.0/28 for site 1, 10.10.0.16/24 for
  site 2, and 10.10.1.0/23 for site 3.
• B. 10.10.0.0/28 for site 1, 10.10.0.16/24 for
  site 2, and 10.10.0.0/23 for site 3.
• C. 10.10.0.0/27 for site 1, 10.10.0.16/24 for
  site 2, and 10.10.1.0/23 for site 3.
• D. 10.10.0.0/28 for site 1, 10.10.0.0/24 for site
  2, and 10.10.0.0/23 for site 3.
• Answer A

• QUESTION NO 10
• Which component of a virtual architecture is
  often referred to as a Virtual Machine Manager
  (VMM) and can manage the virtualization of
  memory, storage, CPU, and other processes while
  being hidden from the guest machine?
• Terminal emulator
• Virtual machine
• Host machine
• Hypervisor
• Answer D

4

• QUESTION NO 11
• An interface on router R1 has been enabled for
  IPv6 using the following command R1(config-if)
  ipv6 enable
• What type of address will gert generated from
  this?
• Automatic generation of link-local address using
  modified EUI-64 interface ID on the MAC address
• Direct link-local address using EUI-64 interface
  ID
• Automatic generation of site-local address using
  modified EUI-64 interface ID in low order 64
  bits of address
• This will enable automatic address assignment via
  IPv6 DHCP.
• Answer A

• QUESTION NO 12
• OSPF is being implemented in a new network. Which
  of the following events happens before routing
  information can be exchanged when OSPF is
  initiated on a network? (Select two)
• An adjacency building process is optimized by
  electing a DR and BDR for every multi- access
  network
• Unicast hello packets discover neighbors
• DR and BDR election process is done to optimize
  point-to-point network
• Multicast hello packets are used to discover OSPF
  neighbors
• Neighbor discovery is initiated by BDR in a
  multi-access network
• Answer A, D

• QUESTION NO 13
• A router has three routing processes running
  OSPF, RIP, and EIGRP. All three processes have
  learned various routes to 10.100.10.0/24. Which
  path will be chosen by the router, assuming
  default values?
• The EIGRP Route, with an Administrative Distance
  of 90.
• The OSPF Route, with an Administrative Distance
  of 90.
• The OPSF Route, with an Administrative Distance
  of 110.
• The RIP Route, with an Administrative Distance of
  110.
• Answer A

5

• QUESTION NO 14
• Which command in a Cisco router encrypts a
  password with strong encryption and is
  recommended according to Cisco best practices?
• enable secret
• enable password
• service password-encryption
• enable password-secret
• Answer A

• QUESTION NO 15
• Which of the following choices correctly display
  the default hello and dead timers for a Cisco
  device running OSPF on an ethernet link?
• Hello 30 seconds, Dead 90 seconds
• Hello 20 seconds, Dead 60 seconds
• Hello 10 seconds, Dead 30 seconds
• Hello 10 seconds, Dead 40 seconds
• Answer D

• QUESTION NO 16
• You are required to configure NAT on an Internet
  facing router. Which of the following is NOT a
  valid NAT address type? (Choose two)
• Inside Global
• Outside Global
• Inside Local
• Inside Global
• Inside Public
• Inside Private
• Answer E, F

QUESTION NO 17
6

• You have configured NTP on router R1 and wish to
  verify the configuration by issuing the show
  ntp status command on R1. What can be determined
  by using this command? (Choose three).
• Whether the NTP server is authoritative
• clock synchronization status
• the clock offset
• The NTP stratum level
• The NTP version used by the server
• Answer B, C, D

• QUESTION NO 18
• You need to configure syslog on router R1 to send
  log messages to a centralized server. You want
  to send all log messages with a severity level of
  notifications and greater to the server. Which
  syslog severity level should be chose to do this?
• Severity 3
• Severity 4
• Severity 5
• Severity 6
• Answer C

• QUESTION NO 19
• You want to backup your router configuration
  files to a central server without having to login
  using a username and password. Which protocol
  should be enabled in order to do this?
• TFTP
• FTP
• SSH
• Telnet
• Answer A

QUESTION NO 20 When you boot up your Microsoft
Windows based PC on the corporate LAN, you are
able to access the Internet without having to
manually enter any information at all in your PC.
Which protocol was used to enable this
functionality? A. CDP
7

• DHCP
• SNMP
• DNS
• STP
• Answer B