Title: CLAAS AXION 870 850 830 810 CMATIC Tractor (Type A61) Service Repair Manual Instant Download (Serial Number A6100100 and up)
1AXION 870-850-830-810 CMATIC Repair manual
Original repair manual
2Validity of this repair manual This repair manual
applies to the following tractor
Description Type Tractor serial number Tractor serial number
Description Type From to
AXION 800 A61 A6100100
3Complete engine Technical specifications
Number Value Note Description
1 920 kg Complete engine
For unspecified tightening torques, refer to the section entitled "Tightening torques". For unspecified tightening torques, refer to the section entitled "Tightening torques". For unspecified tightening torques, refer to the section entitled "Tightening torques".
- WARNING
- Lifting heavy components.
- Risk of death or serious injury.
- Use certified slings or chains in perfect working
order. - Use a certified hoist in perfect working order.
- Use a certified jack or stand which can support
the load. - Use the jack or stand on a flat, horizontal,
sufficiently firm surface. - Place the jack or stand in a suitable location.
- NOTICE
- Lubricants and fuels end up in the environment.
- Environmental pollution
- Collect and store lubricants and fuels in
suitable containers and dispose of them properly.
4https//www.ebooklibonline.com Hello dear
friend! Thank you very much for reading. Enter
the link into your browser. The full manual is
available for immediate download. https//www.ebo
oklibonline.com
5Special tool
Special tool Reference no.
Carriage to be uncoupled No. 00 1148 105 0
Special tool Reference no.
Extension No. 00 1148 106 0
6Special tool Reference no. Special tool Reference no.
1 Engine lifting brackets kit No. 00 1152 870 0
Component parts of the NEF 6 kit Component parts of the NEF 6 kit
2 Bracket at the front of the engine No. 1149 878 1/1
3 Bracket at the right-hand side of the engine No. 1149 878 1/2D
4 Bracket at the left-hand side of the engine No. 1149 878 1/2G
7Special tool Reference no.
Flywheel rotating tool No. 00 1150 142 0
- Removal
- Drain the engine.
- Drain the air conditioning circuit.
- Drain the pneumatic brake circuit (optional).
- Drain the cooling circuit.
- Remove the engine bonnet.
- Engine bonnet
- .
- Remove the left-hand tank.
- Main tankFunction01 Engine
- .
- Remove the exhaust gas post-treatment system. .
8- Remove bolts (1) and (2) and (6).
- Remove the protective panel (3).
- Disconnect the electric starting motor wiring
harnesses (4). - Remove the electric starting motor (5).
- Remove the bolts (1).
- Move aside the protective panel (2).
9- Remove the clamp (1).
- Remove the bolt (2) from the mounting clamp.
- Remove the coolant hose (3).
- Remove the mounting clamps (1), (2) and (3).
- Mark and remove the rigid pipe connectors.
10- Remove the clamps (1).
- Loosen the flexible pipe connector (2).
- Undo connectors (1) and (2).
- Remove the clamp (3).
- Remove the clamps (4), (5), (6) and remove the
hoses (7), (8) and (9).
11- Remove the clamp (1).
- Remove the connector (2) and the bolt (3).
- Remove the air conditioning pipes (4) and (5).
- Seal the openings of the air conditioning
compressor. Attach the pipes to the cabin.
12- Mark and disconnect the electrical wiring harness
(1) of the engine. - Mark and disconnect the electrical wiring harness
(2) of the front linkage. - Mark and disconnect the electrical wiring harness
(3) of the front axle.
- Remove the bolts (1).
- Remove the tank mounting panel (2).
13- Decompress the front axle suspension circuit by
acting on the suspended front axle hydraulic
block (1). - Decompressing the CARRARO front axle suspension
hydraulic circuit
- Remove the clamps (2).
- Undo the flexible pipe connector (1).
- Remove the clamps (2).
- Undo the pipe connectors (1).
14- Uncouple the pipes (2), (3) and (4).
- Remove the bolts (1) from the front axle
hydraulic block support. - Remove the suspended front axle hydraulic block.
- Remove the clamps (1), (2), (3) and (4).
- Uncouple the hydraulic connectors.
- Uncouple the air connectors (5) and (6)
(optional). - Remove the bolts (7) and (8) from the air
regulator support (optional). - Remove the air regulator (9) (optional).
15- Remove the clamps (1).
- Mark and uncouple the hydraulic connectors (2).
- Remove the pipes (3).
- Remove the nuts (1) and (2) from the transmission
shaft protective panel. - Remove the transmission shaft protective panel
(3).
16- Remove the bolts (1) and (2) from the
transmission shaft. - Remove the transmission shaft (3).
- Remove the bolts (1) and (2).
- Remove the clamps (3), (4), (5) and (9).
- Uncouple the pipes (6), (7) and (8).
17- Disconnect the connector (10).
- Remove the hose (6).
- Remove the clamps (4) and (5).
- Remove the hose (3).
- Remove the bolts (2).
- Remove the expansion bottle assembly and its
support (1).
18- Remove the clamp (4).
- Remove the clamps (3).
- Remove the hoses (1) and (2).
- Remove the connectors (1) and (2).
- Remove the bolt (3) from the support bracket.
- Remove the pipes (4) and (5).
- Remove the bolt (1).
- Remove the wiring harness (2) of the "Visctronic"
"C080" fan.
19- Remove the bolts and nuts (2).
- Remove the turbocharger protective panel (1).
- Remove the bolts (1).
- Remove the nuts (2).
- Remove the subframe (1) with a suitable lifting
tool.
20Suggest If the above button click is invalid.
Please download this document first, and then
click the above link to download the complete
manual. Thank you so much for reading
21The support weighs 36 kg.
- Remove the nuts (1).
- Remove the apron (2).
- Remove the coolant pipe (1) located at the rear
of the cylinder head.
- Undo the nut (1) of the visco coupler.
22https//www.ebooklibonline.com Hello dear
friend! Thank you very much for reading. Enter
the link into your browser. The full manual is
available for immediate download. https//www.ebo
oklibonline.com