New Holland GT20A GT22A Garden Tractor (Model No.725056006-T04AF0001 & Up 725056016-T04AG0001 & Up) Operator’s Manual Instant Download (Publication No.87059743)

1
NEW HOLLAND
m3614
OPERATORS MANUAL
GT20A, GT22A Garden Tractor Model
No. 725056006T04AF0001 Up 725056016T04AG0001
Up
Publication Number 87059743 3/2005
2
Page Using the Parking Brake . . . . . . . . . .
. . . . . . . . . 11 Starting and Stopping the
Engine . . . . . . . . . . . . 12 Operating the
Power Take Off (PTO) . . . . . . . . . 12 The
Safety Interlock System . . . . . . . . . . . . .
. . . 13 Gauges and Indicator Lights . . . . .
. . . . . . . . . . . 14 Driving Forward or
Backward . . . . . . . . . . . . . .
. 15 Stopping the Machine . . . . . . . . . . . .
. . . . . . . . . 16 Using the Cruise Control . .
. . . . . . . . . . . . . . . . . 16 Raising
and Lowering Attachments . . . . . . . . . . .
17 Positioning the Seat . . . . . . . . . . . . .
. . . . . . . . . . 17 Lights . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
17 Positioning the Tilt Steering Wheel . . . .
. . . . . . . 18 Centering the Steering Wheel
(Power Steering Models) . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . 18 The
Automatic Speed Reduction Feature . . . . . .
18 Pushing the Machine by Hand . . . . . . . . .
. . . . . . 18 Maintenance . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . .
. 19 Recommended Maintenance Schedule . . . . .
. . . 19 Servicing the Air Cleaner . . . . . . .
. . . . . . . . . . . 20 Servicing the Engine Oil
. . . . . . . . . . . . . . . . . . . 21 Changing
Spark Plugs . . . . . . . . . . . . . . . . . . .
. . 22 Greasing the Tractor . . . . . . . . . .
. . . . . . . . . . . . 23 Maintaining the Tire
Pressure . . . . . . . . . . . . . . . 24
Servicing the Brake . . . . . . . . . . . . . . .
. . . . . . . . 24 Draining the Fuel Tank . . .
. . . . . . . . . . . . . . . . . 25 Replacing
the Fuel Filter . . . . . . . . . . . . . . . . .
. . 26 Servicing the Front Wheel Toe-In . . . .
. . . . . . . . 26
Warning
CALIFORNIA Proposition 65 Warning The engine
exhaust from this product contains chemicals
known to the State of California to cause cancer,
birth defects, or other reproductive harm.
This engine is not equipped with a spark
Important
arrester muffler. It is a violation of California
Public
Resource Code Section 4442 to use or operate this
engine on any forest-covered, brush-covered or
grass-covered land. Other states or federal areas
may have similar laws. This spark ignition system
complies with Canadian ICES-002. Ce système
dallumage par étincelle de véhicule est conforme
à la norme NMB-002 du Canada. The enclosed Engine
Owners Manual is supplied for information
regarding The U.S. Environmental Protection
Agency (EPA) and the California Emission Control
Regulation of emission systems, maintenance and
warranty. Keep this engine Owners Manual with
your unit. Should this engine Owners Manual
become damaged or illegible, replace immediately.
Replacements may be ordered through the engine
manufacturer.
Contents Changing Transaxle Fluid . . . . . . . . . . . . . . . . . . Models Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 28
Page Replacing Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Replacing Headlights . . . . . . . . . . . . . . . . . . . . . . 29
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Replacing Taillights . . . . . . . . . . . . . . . . . . . . . . . 29
Safe Operating Practices . . . . . . . . . . . . . . . . . . . 3 Servicing the Battery . . . . . . . . . . . . . . . . . . . . . . 30
New Holland Riding Mower Safety . . . . . . . . . . 5 Cleaning and Storage . . . . . . . . . . . . . . . . . . . . . . 32
Slope Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Safety and Instruction Decals . . . . . . . . . . . . . . . 7 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Check Before Operating . . . . . . . . . . . . . . . . . . . . . . 8 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Opening the Hood . . . . . . . . . . . . . . . . . . . . . . . . 8 Loose Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Closing the Hood . . . . . . . . . . . . . . . . . . . . . . . . . 8 Checking Front Wheel Toe-in . . . . . . . . . . . . . . . 40
Removing the Side Panels . . . . . . . . . . . . . . . . . . 8 Ensuring that the Steering Linkage is Centered . 40
Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Checking Tire Pressure . . . . . . . . . . . . . . . . . . . . 40
Checking the Engine Oil Level . . . . . . . . . . . . . . 9 Activating the Battery . . . . . . . . . . . . . . . . . . . . . 41
Check for Debris . . . . . . . . . . . . . . . . . . . . . . . . . 10 Installing the Drawbar Hitch Pin . . . . . . . . . . . . . 42
Check the Safety Interlock System . . . . . . . . . . . 11 Checking the Wiring and Fasteners . . . . . . . . . . . 42
Check the Brake . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Test Driving the Tractor . . . . . . . . . . . . . . . . . . . . 42
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Think Safety First . . . . . . . . . . . . . . . . . . . . . . . . 11
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Cleaning the Power Steering Filter (Power Steering
All Rights Reserved Printed in the USA
2004 CNH America L.L.C. Racine, WI
2
3
Introduction

• Caution signals a hazard that may cause minor or
  moderate injury if the recommended precautions
  are not followed.
• Two other words are also used to highlight
  information. Important calls attention to special
  mechanical information, and Note emphasizes
  general information worthy of special attention.
• Determine the left and right side of the machine
  from the normal operating position.
• Safety
• This machine meets or exceeds the B71.1-1998
  specifications of the American National Standards
  Institute, in effect at the time of production.
  However, improper use or maintenance by the
  operator or owner can result in injury. To reduce
  the potential for injury, comply with these
  safety instructions and always pay attention to
  the safety alert symbol, which means CAUTION,
  WARNING, or DANGERpersonal
• safety instruction. Failure to comply with the
  instruction may result in personal injury or
  death.
• Safe Operating Practices
• The following instructions are from ANSI standard
  B71.11998.
• This product is capable of amputating hands and
  feet and throwing objects. Always follow all
  safety instructions to avoid serious injury or
  death.
• General Operation
• Read, understand, and follow all instructions in
  the operator s manual and on the machine before
  starting.
• Allow only responsible adults who are familiar
  with the instructions to operate the machine.
• Clear the area of objects such as rocks, toys,
  wire, etc., which could be picked up and thrown
  by the blade.
• Be sure the area is clear of other people before
  mowing. Stop the machine if anyone enters the
  area.
• Never carry passengers.
• Do not mow in reverse unless absolutely
  necessary. Always look down and behind before and
  while backing.

Thank you for purchasing a New Holland
product. All of us at New Holland want you to be
completely satisfied with your new product, so
feel free to contact your local Authorized
Service Dealer for help with service, genuine
replacement parts, or other information you may
require. Whenever you contact your Authorized
Service Dealer or the factory, always know the
model and serial numbers of your product. These
numbers will help the Service Dealer or Service
Representative provide exact information about
your specific product. You will find the model
and serial number plate at the location shown in
Figure 1.
1
m3605
Figure 1 1. Model and serial number
plate Write the product model and serial
numbers in the space below
Model No. Product ID No.
Read this manual carefully to learn how to
operate and maintain your product correctly.
Reading this manual will help you and others
avoid personal injury and damage to the product.
Although we design, produce and market safe,
state-of-the-art products, you are responsible
for using the product properly and safely. You
are also responsible for training persons, who
you allow to use the product, about safe
operation. The warning system in this manual
identifies potential hazards and has special
safety messages that help you and others avoid
personal injury, even death. Danger, Warning, and
Caution are signal words used to identify the
level of hazard. However, regardless of the
hazard, be extremely careful. Danger signals an
extreme hazard that will cause serious injury or
death if the recommended precautions are not
followed. Warning signals a hazard that may cause
serious injury or death if the recommended
precautions are not followed.
3
4
https//www.ebooklibonline.com Hello dear
friend! Thank you very much for reading. Enter
the link into your browser. The full manual is
available for immediate download. https//www.ebo
oklibonline.com
5

• Never leave a running machine unattended. Always
  turn off blades, set parking brake, stop engine,
  and remove keys before dismounting.
• Turn off blades when not mowing.
• Stop the engine before removing the grass catcher
  or unclogging the chute.
• Mow only in daylight or good artificial light.
• Do not operate the machine while under the
  influence of alcohol or drugs.
• Watch for traffic when operating near or crossing
  roadways.
• Use extra care when loading or unloading the
  machine into a trailer or truck.
• Always wear safety goggles or safety glasses with
  side shields when operating mower.
• Data indicates that operators, age 60 years and
  above, are involved in a large percentage of
  riding
• mower-related injuries. These operators should
• evaluate their ability to operate the riding
  mower safely enough to protect themselves and
  others from serious injury.

• Do not mow on wet grass. Reduced traction could
  cause sliding.
• Do not try to stabilize the machine by putting
  your foot on the ground.
• Do not use a grass catcher on steep slopes.

Children Tragic accidents can occur if the
operator is not alert to the presence of
children. Children are often attracted to the
machine and the mowing activity. Never assume
that children will remain where you last saw them.

• Keep children out of the mowing area and under
  the watchful care of another responsible adult.
• Be alert and turn the machine off if children
  enter the area.
• Before and while backing, look behind and down
  for small children.
• Never carry children, even with the blades off.
  They may fall off and be seriously injured or
  interfere with safe machine operation.
• Never allow children to operate the machine.
• Use extra care when approaching blind corners,
  shrubs, trees, the end of a fence or other
  objects that may obscure vision.

Slope Operation Slopes are a major factor related
to loss-of-control and tip-over accidents, which
can result in severe injury or death. All slopes
require extra caution. If you cannot back up the
slope or if you feel uneasy on it, do not mow it.
Service

• Mow up and down slopes, not across.
• Remove obstacles such as rocks, tree limbs, etc.
• Watch for holes, ruts or bumps. Uneven terrain
  could overturn the machine. Tall grass can hide
  obstacles.
• Use slow speed. Choose a low gear so that you
  will not have to stop or shift while on the
  slope.
• Follow New Hollands recommendations for wheel
  weight or counterweights to improve stability.
• Use extra care with grass catchers or other
  attachments. These can change the stability of
  the machine.
• Keep all movement on slopes slow and gradual. Do
  not make sudden changes in speed or direction.
• Avoid starting or stopping on a slope. If tires
  lose traction, disengage the blades and proceed
  slowly straight down the slope.
• Do not turn on slopes unless necessary, and then,
  turn slowly and gradually downhill, if possible.
• Do not mow near drop-offs, ditches, or
  embankments. The machine could suddenly turn over
  if a wheel goes over the edge of a cliff or
  ditch, or if an edge caves in.

• Use extra care when handling gasoline and other
  fuels. They are flammable and vapors are
  explosive.

• Use only an approved container.
• Never remove the gas cap or add fuel when the
  engine is running. Allow the engine to cool
  before refueling. Do not smoke.
• Never refuel the machine indoors.
• Never store the machine or fuel container inside
  where there is an open flame, such as near a
  water heater or furnace.

• Never run a machine inside a closed area.
• Keep nuts and bolts tight, especially the blade
  attachment bolts. Keep equipment in good
  condition.
• Never tamper with safety devices. Check their
  proper operation regularly.
• Keep the machine free of grass, leaves, or other
  debris build-up. Clean up oil or fuel spillage.
  Allow the machine to cool before storing.
• Stop and inspect the equipment if you strike an
  object. Repair, if necessary, before restarting.

4
6

• Grass catcher components are subject to wear,
  damage and deterioration, which could expose
  moving parts or allow objects to be thrown.
  Frequently check components and replace with
  manufacturers recommended parts, when necessary.
• Mower blades are sharp and can cut. Wrap the
  blade(s) or wear gloves, and use extra caution
  when servicing them.
• Use only genuine New Holland replacement parts to
  ensure that original standards are maintained.

• Use only genuine replacement parts to ensure that
  original standards are maintained.
• Mow up and down slopes greater than 5?, not
  across.
• Mow downhill only on slopes above 10?, never mow
  uphill. If a steep slope must be ascended, back
  up the hill, and drive forward down the hill,
  keeping the machine in gear.
• Do not operate machine on hillsides or slopes
  exceeding 15?.
• Avoid turning on slopes. If you must turn, turn
  slowly and gradually downhill, if possible.
• Do not use a grass catcher on steep slopes. Heavy
  grass bags could cause loss of control or
  overturn the machine.
• Use only New Holland-approved attachments.
  Warranty may be voided if used with unapproved
  attachments.

New Holland Riding Mower Safety The following
list contains safety information specific to New
Holland products or other safety information that
you must know that is not included in the ANSI
standard.

• Warning
• Engine exhaust contains carbon monoxide, an
  odorless, deadly poison that can kill you.
• Do not run the engine indoors or in an enclosed
  area.
• Stop the engine, disconnect spark plug wire(s)
  and remove key before performing any service,
  repairs, maintenance or adjustments.
• Slow down before turning. Sharp turns on any
  terrain may cause loss of control.
• Never leave a running machine unattended. Always
  turn off blades, set parking brake, stop engine,
  and remove the ignition and reverse interlock
  keys before dismounting.
• Keep hands, feet, hair and loose clothing away
  from attachment discharge area, underside of
  mower and any moving parts while engine is
  running.
• Do not touch equipment or attachment parts which
  may be hot from operation. Allow to cool before
  attempting to maintain, adjust or service.
• Remove obstacles such as rocks, tree limbs, etc.
  from the mowing area. Watch for holes, ruts or
  bumps, as uneven terrain could overturn the
  machine. Tall grass can hide obstacles.
• Battery acid is poisonous and can cause burns.
  Avoid contact with skin, eyes and clothing.
  Protect your face, eyes and clothing when working
  with a battery.
• Battery gases can explode. Keep cigarettes,
  sparks and flames away from battery.

5
7
Slope Chart
6
8
Safety and Instruction Decals
Safety decals and instructions are easily visible
to the operator and are located near any area of
potential danger. Replace any decal that is
damaged or lost.
On the drive shaft cover (Part No. TR107D9221)
Battery Symbols Some or all of these symbols are
on your battery.

1. Explosion hazard.
2. No fire, open flames, or smoking.
3. Caustic liquid/chemical burn hazard.
4. Wear eye protection.
5. Read the Operators Manual.
6. Keep bystanders a safe distance from the
   battery.

1. Wear eye protection explosive gases can cause
   blindness and other injuries.
2. Battery acid can cause blindness or severe
   burns.
3. Flush eyes immediately with water and get
   medical help fast.
4. Contains lead do not discard.

(2) Under the side shield (Part No. TR98D5014)
On the battery strap (Part No. TR93D1265)
On the drive shaft tunnel (Part No. TR80D8760)
On the front of the seat bracket (Part No.
TR99D2985)
On the front of the seat bracket (Part No.
TR99D8894)
On the Battery (Part No. TR104D4163)
On the engine bulkhead (Part No. TR98D5012)
7
9
Check Before Operating

• Closing the Hood
• The hood catch is located at the left hand corner
  of the grill.
• Press rearward on the hood catch as you begin to
  lower the hood.
• Push the hood down until the latch closes.

Each time before operating your tractor, check
the following

• Fuel level
• Engine oil level
• Debris on the air-intake screens
• Debris in the engine area
• Debris on the rear transaxle cover
• The safety interlock system
• The brake

1
2 2
Some of these steps will require that you open
the hood or remove the side panels on the tractor.
Front of tractor Figure 3 2. Hood hinges
M-4227

• Opening the Hood
• Park the machine on a level surface, disengage
  the power take off (PTO), set the parking brake,
  lower the attachment lift, stop the engine, and
  remove the ignition key.
• Push the hood latch to the left (Fig. 2).

1. Hood catch

• Removing the Side Panels
• Park the machine on a level surface, disengage
  the PTO, set the parking brake, lower the
  attachment lift, stop the engine, and remove the
  ignition key.
• Raise the hood.
• Lift up and twist each of the two side panel
  latches until they line up with the open slot
  (Fig. 4).

1
m3314
2
1
Figure 2 1. Hood latch 3. Raise the hood to
full height. Caution
m3318
Components under the hood will be hot if the
tractor has been running. If you touch hot
components you may be burned. Allow the tractor
to cool before performing maintenance or touching
components under the hood.
Figure 4 2. Open slot
1. Side panel latch

1. Pull the top of the side panel toward you until
   the side panel latches pass through the open
   slot.
2. Lift the side panel from the tractor.

8
10
Adding Fuel Use unleaded, regular gasoline
suitable for automotive use (85 pump octane
minimum). Leaded regular gasoline may be used if
unleaded regular is not available.

• Cleans the engine while it runs
• Eliminates gum-like varnish buildup in the fuel
  system, which causes hard starting

Do not use fuel additives containing
Important
methanol or ethanol.
Do not use methanol, gasoline containing
Important
methanol, or gasohol containing more than 10
ethanol
Add the correct amount of fuel stabilizer/conditio
ner to the gasoline, as directed by the
manufacturer. Note A fuel stabilizer/conditioner
is most effective when mixed with fresh gasoline.
because the fuel system could be damaged. Do not
mix oil with gasoline.
Danger

• Filling the Fuel Tank
• Park the machine on a level surface, disengage
  the PTO, set the parking brake, lower the
  attachment lift, stop the engine, and remove the
  ignition key.
• Note When filling the tank, make sure that the
  machine is on a level surface so that adequate
  air space is allowed.
• Clean around the fuel tank cap and remove the
  cap.
• Add fuel until the fuel level is 1/4 to 1/2 inch
  (6 mm to 13 mm) below the bottom of the filler
  neck.
• This space in the tank allows for expansion of
  the fuel. Do not fill the fuel tank completely.
• Install the fuel tank cap securely.
• Wipe up any gasoline that may have spilled.

• In certain conditions, gasoline is extremely
  flammable and highly explosive. A fire or
  explosion from gasoline can burn you and others
  and can damage property.
• Fill the fuel tank outdoors, in an open area,
  when the engine is cold. Wipe up any gasoline
  that spills.
• Do not fill the fuel tank completely full. Add
• gasoline to the fuel tank until the level is 1/4
  to 1/2 inch (6 to 13 mm) below the bottom of the
  filler neck. This empty space in the tank allows
  gasoline to expand.
• Never smoke when handling gasoline, and stay
• away from an open flame or where gasoline fumes
  may be ignited by a spark.
• Store gasoline in an approved container and keep
  it out of the reach of children. Never buy
• more than a 30-day supply of gasoline.
• Always place gasoline containers on the ground
  away from your vehicle before filling.
• Do not fill gasoline containers inside a vehicle
• or on a truck or trailer bed because interior
  carpets or plastic truck bed liners may insulate
  the container and slow the loss of any static
  charge.
• When practical, remove gas-powered equipment from
  the truck or trailer and refuel the equipment
  with its wheels on the ground.
• If this is not possible, then refuel such
• equipment on a truck or trailer from a portable
  container, rather than from a gasoline dispenser
  nozzle.
• If a gasoline dispenser nozzle must be used,
• keep the nozzle in contact with the rim of the
  fuel tank or container opening at all times until
  fueling is complete.

• Checking the Engine Oil Level
• Park the machine on a level surface, disengage
  the PTO, set the parking brake, lower the
  attachment lift, stop the engine, and remove the
  ignition key.
• Open the hood.
• Clean around the oil dipstick (Fig. 5) so dirt
  cannot fall into the dipstick tube and damage the
  engine.
• 1

2

• Using Stabilizer/Conditioner
• Use a fuel stabilizer/conditioner in the machine
  at all times to provide the following benefits
• Keeps gasoline fresh during storage of 90 days or
  less. For longer storage, drain the fuel tank.

m3246
Figure 5
1. Dipstick 2. Oil filler
9
11
4. Pull out the oil dipstick and wipe the metal
end clean (Fig. 6).
1
1
m3412
Figure 7 Arrows show air intake and exhaust
path 1. Air intake screens (1 of 3 shown)
m3219
Figure 6
1. Metal end

1. Wipe away debris before each use and/or during
   use, if required.
2. Wipe away any accumulated debris from the
   rotating air-intake screen (Fig. 8).

1. Slide the oil dipstick fully into the dipstick
   tube (Fig. 5).
2. Pull the dipstick out and look at the metal end
   (Fig. 6). If the oil level is low (near the L
   mark), add oil refer to Engine Oil, page 21.

Danger
Do not overfill the crankcase with oil
Important
because this may result in engine damage.

• The rotating air-intake screen and drive shaft
  can catch fingers, hands, and loose clothing,
  causing amputation or other severe injury when
  moving.
• Do not operate the tractor without the side
  panels and hood in place.
• Keep fingers, hands and clothing clear of the
• rotating air-intake screen and drive shaft.
• Stop the engine and remove the ignition key
  before performing maintenance.

Check for Debris
Operating the engine with a blocked grass
Important
screen, dirty or plugged cooling fins, and/or
cooling

• shrouds removed, will result in engine damage
  from overheating.
• Park the machine on a level surface, disengage
  the PTO, set the parking brake, lower the
  attachment lift, stop the engine, and remove the
  ignition key.
• Check for debris on the air-intake screens (Fig.
  7).

1 Figure 8 1. Rotating air intake screen
m3617
5. Clean any debris build-up from the engine area
with a brush or blower.
10
12
Operation
If possible, blow dirt out (Fig. 9), rather
Important
than washing it out. If water is used, keep it
away from electrical items.
Think Safety First Please carefully read all the
safety instructions on pages 3 through 7. Knowing
this information could help you, your family,
pets, or bystanders avoid injury.
Controls Become familiar with all the controls
(Fig. 11) before you start the engine and operate
the machine. 7 5
m3615
Figure 9
Do not clean the machine using pressurized
Important
15
8
water. High-pressure washing can damage the
electrical system or deplete grease. 6. Clean
debris from the rear transaxle cover (Fig.
10). Note The rear transaxle cover is an
air-intake area for cooling the transaxle.
2
6
11
9 16 10 12
1 3
4
1
13
m3436
Figure 10
14
1. Rear transaxle cover
Check the Safety Interlock System Always check
the interlock system before operating the
tractor. Instructions for checking the interlock
system are found in the Operation section, page
13.
m3597

• Figure 11
• Hour meter
• Ignition switch
• Brake pedal
• Parking brake lever
• HighLow range lever
• Cruise control switch
• Steering wheel tilt lever
• Traction control pedal

1. Throttle
2. Choke
3. PTO switch
4. Seat adjustment lever
5. Engine oil temperature gauge
6. Attachment lift lever
7. Indicator lights
8. Fuel gauge

Check the Brake Refer to Checking and Adjusting
the Brake, page 24.
Using the Parking Brake Set the parking brake
when you stop the machine or leave it unattended.
11
13

• Setting the Parking Brake
• Push the brake pedal (Fig. 11) down and hold it.
• Lift the parking brake lever (Fig. 11) up and
  gradually take your foot off the brake pedal. The
  brake pedal should stay down.

2
1
3

• Releasing the Parking Brake
• Push down on the brake pedal (Fig. 11). The
  parking brake lever should release.
• Release the brake pedal.

4
m3312

• Figure 13
• Run
• Start

1. Stop
2. Run with lights

• Starting and Stopping the Engine
• Starting
• Sit down on the seat.
• Push the brake pedal down.
• Note The engine will not start unless you push
  the brake pedal down fully.
• Push the PTO switch to the off position (Fig. 12).

7. When the engine starts, release the key.
Do not crank the engine continuously for
Important
more than 10 seconds at a time. If the engine
does not

• start, allow a 60 second cool-down period between
  starting attempts. Failure to follow these
  guidelines can burn out the starter.
• After the engine starts, move the choke lever to
  the off position (Fig. 12).
• If the engine stalls or hesitates, move the choke
  lever back to the on position for a few seconds.
  Then, move the throttle lever to the desired
  setting. Repeat this as required.
• Allow the engine to warm up before using it.

2

• Stopping
• Move the throttle lever to the slow position
  (Fig. 12).
• Allow the engine to run for a short time to cool
  down.
• Turn the ignition key to the stop position (Fig.
  13).
• Remove both the ignition and reverse interlock
  keys when the equipment is not in use or
  unattended.

1
3
m3257
Figure 12 3. PTO switch

1. Throttle
2. Choke

Operating the Power Take Off (PTO) The power take
off (PTO) runs the various powered attachments
such as mowers, snowthrowers, and tillers. If the
ignition key is in the run or lights position and
the PTO is engaged, the PTO indicator light will
be on. When this light is on, it is a reminder
the implement is being powered and the starter
will not crank while the PTO is engaged. Always
turn off the PTO before getting off the seat.

1. Move the choke lever to the on position (if the
   engine is cold) (Fig. 12).
2. Move the throttle lever halfway to the fast
   position (Fig. 12).
3. Turn the ignition key clockwise and hold it in
   the start position (Fig. 13).

12
14
Suggest If the above button click is invalid.
Please download this document first, and then
click the above link to download the complete
manual. Thank you so much for reading
15

• Engaging the PTO
• Press the brake pedal to stop the machine.
• Move the throttle lever to the fast position.

Operating in Reverse The tractor has an interlock
feature that prevents mowers, snowthrowers, and
other PTO powered attachments from operating
while the tractor is traveling in reverse. If you
shift into reverse with the PTO engaged, the PTO
will stop. If you need to mow or use other PTO
powered attachments while in reverse gear, you
can temporarily deactivate this interlock. Do not
mow while backing up unless it is absolutely
necessary.
For best performance, always use full
Important
throttle when the PTO is on.
3. Pull the PTO switch to the on position (Fig.
14).
2
1
Danger

• A child or bystander could be backed over by a
  riding mower with blades engaged and cause
  serious personal injury or death.
• Do not mow in reverse unless absolutely
  necessary.
• Always look backward and down before
• backing up.
• Use the reverse interlock switch only if you are
  certain no children or other bystanders will
  appear in the mowing area.
• Always remove both the ignition and reverse
  interlock keys and put them in a safe place out
  of the reach of children or unauthorized users
  when leaving the unit unattended.

m3264
Figure 14 2. Pull (on-engaged)
1. Push (off-disengaged)
Disengaging the PTO Push the PTO switch to the
off position.
The Safety Interlock System Understanding the
Safety Interlock System The safety interlock
system is designed to prevent the engine from
starting unless the following conditions are met

• Before deactivating this interlock, ensure that
  there are no children present on or near the
  property where you are using the tractor, and
  that none are likely to appear while you are
  mowing or operating an attachment. Be extra
  observant after you have chosen to deactivate the
  interlock because the sound of the tractors
  engine might prevent you from being aware that a
  child or bystander has entered the area.
• If you are certain that you can safely mow or
  operate an attachment in reverse, complete the
  following procedure
• Engage the PTO.
• Insert the reverse interlock key into the switch
  (Fig. 15).
• Note Do not insert the reverse interlock key
  unless it is absolutely necessary to mow or
  operate an attachment in reverse. Always remove
  both the ignition and the reverse interlock keys
  and put them in a safe place out of the reach of
  children when leaving the unit unattended.

• You are sitting on the seat
• The brake pedal is depressed
• The PTO is in the off position

• The safety interlock system is designed to stop
  the engine when you do the following
• You rise from the seat when the brake pedal is
  released
• You rise from the seat when the PTO is in the on
  position.
• The safety interlock system is designed to stop
  the PTO when you shift into reverse with the
  power take off (PTO) engaged.

13
16

1. Fully press the brake pedal, set the parking
   brake, push the PTO switch to the Off position,
   and start the engine.
2. Pull the PTO switch to the On position and rise
   slightly from the seat the engine should stop.
3. With the parking brake released, turn the
   ignition key to the Run position without starting
   the engine.
4. Pull the PTO switch to the On position you
   should hear an audible click indicating that the
   PTO is activated and the PTO light should
   illuminate.
5. Move the foot pedal to reverse you should hear
   an audible click, indicating that the PTO is
   deactivated, and the PTO light should turn off.
6. With the parking brake released, turn the
   ignition key to the Run position without starting
   the engine.
7. Pull the PTO switch to the On position.
8. Turn the reverse interlock key and release it.
   The OperatinginReverse warning light should
   illuminate.
9. Move the foot pedal to reverse the PTO and PTO
   light on the dash should remain on.
10. Push the PTO switch to the Off position the PTO
    light and the OperatinginReverse warning light
    should turn off.

1
m4260
Figure 15
1. Reverse interlock key

• Turn the reverse interlock key clockwise until it
  stops and release it.
• A red light illuminates on the front console
  (Fig. 16) to serve as a reminder that the
  interlock has been deactivated.
• Remove the reverse interlock key.
• Once you deactivate the interlock, it stays in
  this modewith your mower blade or PTO powered
  attachment operating whenever you back upand the
  console light stays on until you either disengage
  the PTO or turn off the engine.

• Testing the Safety Interlock System
• Test the safety interlock system each time before
  you use the machine. Do not operate the machine
  if the safety system is not functioning properly.
  If the safety system does not operate as
  described below, have an Authorized Service
  Dealer repair the safety system immediately.
• Fully press the brake pedal. Pull the PTO switch
  to the On position.
• Turn the ignition key to the Start position. The
  starter should not crank.
• Push the PTO switch to the Off position and
  release the brake pedal.
• Turn the ignition key to the Start position. The
  starter should not crank.
• Fully press the brake pedal and set the parking
  brake. Push the PTO switch to the Off position
  and rise from the seat.
• Turn the ignition key to the Start position. The
  starter should not crank.
• Fully press the brake pedal and set the parking
  brake. Push the PTO switch to the Off position
  and start the engine.
• With the engine running, release the parking
  brake and rise slightly from the seat the engine
  should stop.

Gauges and Indicator Lights The indicator lights
(Fig. 16) illuminate when certain controls are
activated and when major malfunctions occur that
need immediate attention. 1 2 3 4 5 6
7
8
m3317

• Figure 16
• Oil pressure light
• Cruise control light
• Engine oil temperature gauge
• Fuel gauge

1. Parking brake light
2. PTO (power take off) light
3. Battery light
4. OperatinginReverse warning light

14
17
https//www.ebooklibonline.com Hello dear
friend! Thank you very much for reading. Enter
the link into your browser. The full manual is
available for immediate download. https//www.ebo
oklibonline.com