John Deere C-11 Culti-Planter Operator’s Manual Instant Download (Publication No.OMN159259)

1
JOHN DEERE
C-11 CULTI-PLANTER
JOHN DEERE C-11 CULTI-PLANTER OMN159259
A1 English
JOHN DEERE DES MOINES WORKS OMN159259 A1
LITHO IN THE U.S.A. ENGLISH
2
To the Purchaser
This new culti-planter was carefully designed and
manufactured to give years of dependable service.
To keep it running efficiently, read the
instructions in this operator's manual. Each
section is clearly identified so you can easily
find the information you need - whether it is
operation, lubrication, or adjustments and
service. Read the Table of Contents to learn
where each section is located. In addition to the
equipment furnished with your culti-planter,
attachments are available to help you do a better
job in special crop conditions. These are
described in the attachments sections of this
manual and can be purchased from your John Deere
dealer. Right-hand and left-hand sides are
determined by facing in the dir ection the
culti-planter will travel when in use.
Record your culti-planter serial numbers in the
space provided on page 48. Your dealer needs this
information to give you prompt, efficient service
when you order parts or attach ments. If your
culti-planter requires replacement parts, go te
your John Deere dealer wh ere you can obtain
genuine John Deere parts - accept no
substitutes. The warranty on this culti-planter
appears on your copy of the purchase order which
you should have received from your dealer when
you purchased the culti-planter. This safety
alert symbol identifies important safety messages
in this manual. When you see this symbol, be
alert to the possibility of personal inju- ry and
carefully read the message that follows.
HYDRAULIC ROW MARKER
I NS E CT I C10E 0P PE R S EE D H 0P PE R
" gt ñ
H E R B I C I D E h 0 P P E R John Deere Four-
Row C- 11 Culti- Planter with Plateless Planter
Units
3
JOHN DEERE C-11 CULTI-PLANTER
PREDELIVERY CHECK LIST Inspect the Culti-planter
after it has been com- pletely assembled to make
sure it operates properly. The following list is
a reminder of the points to inspect and
procedures to follow before delivering the Culti-
planter to the customer. Check off each item if
found satisfactory or after proper adjustment is
made.
OWNER REG ISTER
Name Address Post Office State Implement Serial
No. Implement Model No. Date Purchased
Z Planting units spaced correctly. O Drive
wheel tires inflated to 24 psi. O Planting units
functioning correctly. _at_ Markers operating
properly. _at_ Machine lubricated. I have pertormed
the above predelivery service to
DELIVERY CHECK LIST At th e t inn e of deI i ve
ry , i mp or tan t inf orm at io n should be
conveyed directly to the customer. Check off each
item below as it is fully explained to the cus-
tomer.
the best of my ability.
Date
Signed
_at_ Advise the customer to lubricate the machine
as directed in the operator's manual. D Give the
operator's manual to the customer and explain all
operating adjustments to him. 0 Tell the
customer of safety precautions he must observe
when using this machine. 0 If it becomes
necessary to transport the Culti- planter on
public roads or highways, advise cus- tomer to
chec k with local and state agencies re- garding
the regulations for transporting oversize
equipment and the use of accessory Iights and
devices for adequate warning to operators of oth-
er vehicles on such roads. To the best of my
knowledge, this machine has been delivered ready
for field use and the custom- er has been fully
informed regarding proper care and
operation. Signed Date
Insert for OM- N159 259 (A1) Litho in U.S.A.
4
https//www.ebooklibonline.com Hello dear
friend! Thank you very much for reading. Enter
the link into your browser. The full manual is
available for immediate download. https//www.ebo
oklibonline.com
5
SHIPPING BUNDLES C-11 FIELD CULTIVATOR 1 -
BN130473 Main Frame (15-1/2-foot) 1 - BN130257
Extensions 1 - BN130261 Stub Bars 1 - BN130474
Category 2 and 3 Mast 17 - BN130264 Spring-Teeth
for 4-row culti-planter 19 - BN130264
Spring-Teeth for 6-row culti-planter 17 or 19
sweeps or shovels, as ordered. PLANTER MOUNTING
ATTACHMENT AN131656 Planter Support Bar BN130609
Planter Drives BN130526 Wheel with 6.70-15
Traction Tire, R.H. BN130527 Wheel with 6.70-15
Traction Tire, LH. BN130262 Heavy-Duty Drive
Wheel Support, R.H. BN130263 Heavy-Duty Drive
Wheel Support, L.H. N133674 Planter Drive Shaft
BN130610 Planter Drive Shield PLANTER ROW
UNITS Order from John Deere Planter
Works. PLATELESS PLANTER UNITS
1 -
1 -
1 -
1 -
1 -
1 -
1 -
1 -
BB13280 BB13281 BB13282 BB13283 BB13023 BB13342
Plateless Planting Unit, Disk Opener, Steel Press
Wheel Plateless Planting Unit, Runner Opener,
Steel Press Wheel Plateless Planting Unit, Disk
Opener, Steel Press Wheel with Tire Plateless
Planting Unit, Runner Opener, Steel Press Wheel
with Tire Plateless Planter Seed Hopper (1
required with each of the above bundles) HydRow
Marker (Short Arm)
PLATE-TYPE PLANTER UNITS
BB13011 BB13012 BB13015 BB13016 BB12544 BB13342
Plate-Type Planting Unit, Drill, Disk Opener,
Steel Press Wheel Plate-Type Planting Unit,
Drill, Runner Opener, Steel Press Wheel
Plate-Type Planting Unit, Disk Opener, Steel
Press Wheel with Tire Plate-Type Planting Unit,
Runner Opener, Steel Press Wheel with
Tire Plate-Type Planter Seed Hopper (1 required
with each of the above bundles) HydRow Marker
(Short Arm)
6
ATTACHMENTS FOR PLANTER ROW UNITS Order
attachments for planter row units from J ohn
Deere Plan ter Works PLATE-TYPE OR PLATELESS
PLANTER ROW UNITS
Press Wheel Tires (Traction-Tread) B B96042 4-row
BB96116 6-row
Insecticide Attachments BB96713 4-row BB9671 4
6-row
Press Wheel Bands BB96044 4-row BB96113 6-row
Band Spreader BB96764 4-row BB96765 6-row
Press Wheel Scrapers BB1139 J 4-row BB11690 6-row
Herbicide Attachment with Fenders (For use
Without lnsécticide Attachment) BB96710 4-row
BB96711 6-row
Row Leveling Blades BB96055 4-row BB96122 6-row
Herbicide Attachment Without Fenders (For use
with Insecticide Attachment) BB96622 4-row
BB96624 6-row
PLATE-TYPE PLANTER ROW UNITS
Disk Coverers BB96054 4-row BB96121 6-row
Double- Disk Furrowers (Continued) 9-Inch
Furrower wilh White-Iron Bearings BB96046
4-row BB961 4 6-row
Knife Coverers BB96048 4-row BB96118 6-row
11- Inch Furrower with Anti-Friction
Bearings BB96053 4-row BB96129 6-row
Trash Kickers BB96047 4-row BB96117 6-row
11-Inch Furrower with White-I ron
Bearings BB96058 4-row BB96127 6-row
Gauge Shoes BB96043 4-row BB96112 6-row
12-Inch Furrower with Anti-friction
Bearings BB96078 4-row BB96128 6-row
Double-Disk Furrowers 9-Inch Furrower with
Anti-Friction Bearings BB96057 4-row BB96124 6-row
Double-Disk Seed Openers BB96052 4-row BB96120
6-row
Seed-Packer Wheels BB96050 4-row BB96119 6-row
7
ATTACHMENTS FOR PLANTER ROW UNITSContinued PLATE
LESS PLANTER ROW UNITS
Disk Coverers BB96813 4-row, R.H. BB96814 4-row,
L.H. BB96817 6-row, R.H. BB96818 6-row, L.H.
Double-Disk FurrowersContinued 11-Inch
Furrowers with Anti-Friction Bearings BB96608
4-row BB96609 6-row
11-Inch Furrower with White-I ron Bearings
BB96598 4-row BB96599 6-row
Knife Coverers BB96815 4-row, R.H. BB96816 4-row,
L.H. BB96819 6-row, R.H. BB96820 6-row, L.H.
12-Inch Furrower with Anti-Friction Bearings
BB96604 4-row BB96605 6-row
Double-Disk Furrowers 9-1nch Furrower with
Anti-Friction Bearings BB96638 4-row BB96639 6-row
Sorghum Attachment BB96769 4-row,
regular-rate BB96746 6-row, regular-rate BB96750
4-row, low-rate BB96751 6-row, low-rate
9-I nch Furrower with White-Iron Bearings BB96601
4-row BB96602 6-row
8
Contents
1
Page
Operation
2-17
2
Preparing the Culti- Planter
2
Preparing the Tractor
Plateless Planting Units
3-10
11-17
Plate PIanting Units
17
Transporting
17
Safety Suggestions
18-19
Lubrication
20-22
Service
23-24
Trouble Shooting
Special Equipment
25-40
Assembly
41-46
Specifications
47-48
9
Operation
PREPARING THE TRACTOR Prepare the tractor as
outlined in your C-11 Opera- tor's Manual. Front
End Weights Front end stability is necessary for
efficient opera- tion and safety. Therefore, it
is important that weight be added to the front
end of the tractor according to the following
recommendations. I nsecticide and herbicide
attach ments may be used onIy with certain
tractors as indicated in the chart below. The
Quik-Coupler may be used with the 4520, 4620 and
5020 Tractors only.
This manual contains operation and adjusting, Iu-
brication, service, and assem bly instructions
for the planter drive and planter row
units. Refer to your C-11 Field Cultivator
operator's man- ual for complete operating and
assem bly instructions for the field
cultivator. PREPARING THE CULTI-PLANTER Bolts
and Nuts Before starting to work with your new
culti-planter or one which has been stored, check
to see that ztll nuts are tight. Tire
Inflation Check drive wheel tires to be sure they
are inflated to 24 psi. Lubrication Be sure
culti-planter has been lubricated properly. See
pages 18 and 19.
TOTAL FRONT WEIGHT TOTAL FRONT WEIGHT TOTAL FRONT WEIGHT REQUIRED FOR TRANSPORT STABILITY REQUIRED FOR TRANSPORT STABILITY REQUIRED FOR TRANSPORT STABILITY REQUIRED FOR TRANSPORT STABILITY
Tracto r Panter Rows Row Marker Insecticide Hopper Herbicide Hopper Front End Weight Quik- Coupier
3020 4 yes No No 1505 lbs. No
4000 4 yes yes No 1505 Ibs. No
4000 6 yes No No 1505 lbs. No
4020 4 yes yes No 1505 lbs. No
4320 4 yes yes No 1505 lbs. No
4020 6 yes No No 1505 lbs. No
4320 6 yes No No 1505 lbs. No
4520 4 yes yes yes 820 Ibs. yes
4620 4 yes yes yes 820 Ibs. yes
4520 6 yes yes yes 1505 lbs. yes
4620 6 yes yes yes 1505 Ibs. yes
5020 4or 6 yes yes yes 820 Ibs. yes
10
Operation
3
PLATELESS PLANTING UN ITS
Planting Depth
0 R A C K E T
Planting depth is gauged by the planter press
wheel and not by the depth of the
cultivator. NOT6. When using double-disk
Furrowers, Furrow- ers gauge depth of seed
planter press wheel gauges depth ol furrow.
Each planting unit has a spring which can be ad-
justed to vary the down pressure on the planting
unit. I f the runner tends to ride out of the
ground, raise the planter and move the adjusting
bracket down to the next position. NOTE. Do not
attempt to penettote the plow pen. ln hard soil
conditions, this could cause he cu///-planter
drive wheels fo ra ise otf the ground. Adjust all
planting units so the spring pressure is the same
on each unit. NOTE When operating in the tield,
lo wer fee cu/ti- planter only when the Frac for
is moving forward. This will prevent the plan ter
runners mom clogging in mois I so// conditions.
Planting depth of each unit is determined by the
setting of the depth adjusting cam. To
decrease planting depth, pull out on the
adjusting stop and ro- tate depth adjusting
cam clockwise. To increase planting depth,
pull out on ad justing stop and rotate depth
adjusting cam counterclock'w ise. Each ho\e
represents a change of approximately 3/8 inch
in planting depth. Adjust all units to plant at
the same depth. If necessary, level units with
sleeve adjusting nut an d lock ing nut. Tighten
loc king nut to 150 ft-lbs torque.
11
4 Opera tion
Before removing the hopper, turn the selector
gate to the OFF position to c lose the opening in
the hopper bo!tom. NOTE. Be sore fo turn selector
gafe fo OFF posi- tion for transporting.
Inspection and Cleanout
I S S P fi C T 1 0 h P L 0 G
CLEANOUT PLATE
C L EAN 0 U T S L 0 T
I f seed hoppers are not empty, be certain to
turn the selector gates to the OFF position or
seed will escape from hopper through cleanout
hole. Remove inspection plug and check fingers
periodi- cally. See SERV I GE section, pages
20-22. For best op erat ion , r emo ve clean out
plate and clean out finger pickup housing after
each day's use.
Be certain the CLEANOUT SLOT on the underside of
the finger pickup housing is not clogged. This
will help prevent a buildup of dust and chaff
inside the mechanism.
To plant corn with the finger pickup section of
the planter, move the selector gate from the OFF
position in a clockwise direction until it locks
in place in the position marked GORN.
NOTE The planting units must always be covered
with waterproof material at night or during wet
weath- er.
Selector Gate The selector gate has three
positions mar ked as follows OFF, BEANS SORG
HUM, and CO RN.
To plant soybeans, maize, or other small grain
with the precision feed cup section of the
planter, move the selector gate from OF F
position in a counter- clockwise direction until
it Doc ks in place in the posi- tion marked BEANS
SORG HUM. For instructions on using precision
feed cup see page 6.
12
Operation 5
Seed Spacing Charts
D R I V E R S RO C K ET
fi R I V E S SP R0 t K E T
S PR0 C K ET
GROUND
PLANT POPULATION AND APPROXIMATE DRILLING D ISTANCES IN INCHES WITH 28-TOOTH SPROCKET ON UNIT FOR PLANTER EQUIPPED WITH 6.70-15 TI RES INFLATED TO 24 PSI OF AIR PRESSURE PLANT POPULATION AND APPROXIMATE DRILLING D ISTANCES IN INCHES WITH 28-TOOTH SPROCKET ON UNIT FOR PLANTER EQUIPPED WITH 6.70-15 TI RES INFLATED TO 24 PSI OF AIR PRESSURE PLANT POPULATION AND APPROXIMATE DRILLING D ISTANCES IN INCHES WITH 28-TOOTH SPROCKET ON UNIT FOR PLANTER EQUIPPED WITH 6.70-15 TI RES INFLATED TO 24 PSI OF AIR PRESSURE PLANT POPULATION AND APPROXIMATE DRILLING D ISTANCES IN INCHES WITH 28-TOOTH SPROCKET ON UNIT FOR PLANTER EQUIPPED WITH 6.70-15 TI RES INFLATED TO 24 PSI OF AIR PRESSURE PLANT POPULATION AND APPROXIMATE DRILLING D ISTANCES IN INCHES WITH 28-TOOTH SPROCKET ON UNIT FOR PLANTER EQUIPPED WITH 6.70-15 TI RES INFLATED TO 24 PSI OF AIR PRESSURE PLANT POPULATION AND APPROXIMATE DRILLING D ISTANCES IN INCHES WITH 28-TOOTH SPROCKET ON UNIT FOR PLANTER EQUIPPED WITH 6.70-15 TI RES INFLATED TO 24 PSI OF AIR PRESSURE PLANT POPULATION AND APPROXIMATE DRILLING D ISTANCES IN INCHES WITH 28-TOOTH SPROCKET ON UNIT FOR PLANTER EQUIPPED WITH 6.70-15 TI RES INFLATED TO 24 PSI OF AIR PRESSURE PLANT POPULATION AND APPROXIMATE DRILLING D ISTANCES IN INCHES WITH 28-TOOTH SPROCKET ON UNIT FOR PLANTER EQUIPPED WITH 6.70-15 TI RES INFLATED TO 24 PSI OF AIR PRESSURE
Maximum recommended speed (mph) Drilling distances (inches) Sprocket combinations Sprocket combinations Plant population Plant population
Maximum recommended speed (mph) Drilling distances (inches) (number of teeth) Row width Row width
Maximum recommended speed (mph) Drilling distances (inches) Driver Driven 28 30 38 40
3-1/4 4-7/8 36 12 45800 43350 34220 32510
3-1/2 5-1/4 36 13 42700 39810 31420 29750
4 5-5/8 36 14 39800 37160 29330 27870
4-1/8 6 36 15 37300 35470 28000 26600
4-1/2 6-1/2 36 16 34450 32510 25670 24380
5 7 25 12 32000 29800 23530 22350
5-1/4 7-5/8 25 13 28400 27590 21780 20690
5-1/2 8-1/8 25 14 27590 25780 20300 19220
6 8-3/4 25 15 25400 24080 19010 18060
6-1/2 9-3/8 25 16 23900 22300 17600 16660
PLANT POPULATIO N AND APPROX I MATE DRILLING D ISTANCES IN INCHES WITH 32-TOOTH SPROCKET ON UNIT FOR PLANTER EQU I PPED WITH 6.70-15 TIRES I NFLATED TO 24 PSI OF AIR PRESSURE PLANT POPULATIO N AND APPROX I MATE DRILLING D ISTANCES IN INCHES WITH 32-TOOTH SPROCKET ON UNIT FOR PLANTER EQU I PPED WITH 6.70-15 TIRES I NFLATED TO 24 PSI OF AIR PRESSURE PLANT POPULATIO N AND APPROX I MATE DRILLING D ISTANCES IN INCHES WITH 32-TOOTH SPROCKET ON UNIT FOR PLANTER EQU I PPED WITH 6.70-15 TIRES I NFLATED TO 24 PSI OF AIR PRESSURE PLANT POPULATIO N AND APPROX I MATE DRILLING D ISTANCES IN INCHES WITH 32-TOOTH SPROCKET ON UNIT FOR PLANTER EQU I PPED WITH 6.70-15 TIRES I NFLATED TO 24 PSI OF AIR PRESSURE PLANT POPULATIO N AND APPROX I MATE DRILLING D ISTANCES IN INCHES WITH 32-TOOTH SPROCKET ON UNIT FOR PLANTER EQU I PPED WITH 6.70-15 TIRES I NFLATED TO 24 PSI OF AIR PRESSURE PLANT POPULATIO N AND APPROX I MATE DRILLING D ISTANCES IN INCHES WITH 32-TOOTH SPROCKET ON UNIT FOR PLANTER EQU I PPED WITH 6.70-15 TIRES I NFLATED TO 24 PSI OF AIR PRESSURE PLANT POPULATIO N AND APPROX I MATE DRILLING D ISTANCES IN INCHES WITH 32-TOOTH SPROCKET ON UNIT FOR PLANTER EQU I PPED WITH 6.70-15 TIRES I NFLATED TO 24 PSI OF AIR PRESSURE PLANT POPULATIO N AND APPROX I MATE DRILLING D ISTANCES IN INCHES WITH 32-TOOTH SPROCKET ON UNIT FOR PLANTER EQU I PPED WITH 6.70-15 TIRES I NFLATED TO 24 PSI OF AIR PRESSURE
Maximum Drilling Sprocket combinations Sprocket combinations Plant population Plant population
recommended speed (mph) distances (inches) (number of teeth) Row width
recommended speed (mph) distances (inches) Driver DriVen 30 38 40"
3-1/2 5-1/2 36 12 40700 39010 30800 29260
4 6 36 13 37300 35470 28000 26600
4-1/4 6-1/2 36 14 34450 32510 25670 24380
4-3/4 7 36 15 32000 29800 23530 22350
5 7-3/8 36 16 30380 28400 22400 21200
5-1/4 8 25 12 28000 26490 20910 19870
5-3/4 8-5/8 25 13 25950 25200 19250 18100
6-1/4 9-3/8 25 14 23870 22260 17620 16650
6-3/4 10 25 15 22400 21070 16640 15800
7 10-3/4 25 16 20820 19450 15360 14510
13
6 Operation Seed Spacing ChartsContinued
PLANT POPULATE ON AND ePRoxiMATE oRILLINc DISTANCES IN INCHES WITH 36-TOOTH SPROCKET ON UNIT roR PLANTER aufePcD wfTf 6.7o- Ts TTREs INFLATED To 24 esi or AIR eREssuR PLANT POPULATE ON AND ePRoxiMATE oRILLINc DISTANCES IN INCHES WITH 36-TOOTH SPROCKET ON UNIT roR PLANTER aufePcD wfTf 6.7o- Ts TTREs INFLATED To 24 esi or AIR eREssuR PLANT POPULATE ON AND ePRoxiMATE oRILLINc DISTANCES IN INCHES WITH 36-TOOTH SPROCKET ON UNIT roR PLANTER aufePcD wfTf 6.7o- Ts TTREs INFLATED To 24 esi or AIR eREssuR PLANT POPULATE ON AND ePRoxiMATE oRILLINc DISTANCES IN INCHES WITH 36-TOOTH SPROCKET ON UNIT roR PLANTER aufePcD wfTf 6.7o- Ts TTREs INFLATED To 24 esi or AIR eREssuR PLANT POPULATE ON AND ePRoxiMATE oRILLINc DISTANCES IN INCHES WITH 36-TOOTH SPROCKET ON UNIT roR PLANTER aufePcD wfTf 6.7o- Ts TTREs INFLATED To 24 esi or AIR eREssuR PLANT POPULATE ON AND ePRoxiMATE oRILLINc DISTANCES IN INCHES WITH 36-TOOTH SPROCKET ON UNIT roR PLANTER aufePcD wfTf 6.7o- Ts TTREs INFLATED To 24 esi or AIR eREssuR PLANT POPULATE ON AND ePRoxiMATE oRILLINc DISTANCES IN INCHES WITH 36-TOOTH SPROCKET ON UNIT roR PLANTER aufePcD wfTf 6.7o- Ts TTREs INFLATED To 24 esi or AIR eREssuR PLANT POPULATE ON AND ePRoxiMATE oRILLINc DISTANCES IN INCHES WITH 36-TOOTH SPROCKET ON UNIT roR PLANTER aufePcD wfTf 6.7o- Ts TTREs INFLATED To 24 esi or AIR eREssuR
Maximum recommended speed (mph) Drilling distances (inches) Sprocket combinations Sprocket combinations Plant population Plant population Plant population Plant population
Maximum recommended speed (mph) Drilling distances (inches) (number of teeth) (number of teeth) Row width Row width Row width Row width
Maximum recommended speed (mph) Drilling distances (inches) Driver Driven 28" 30 40
4 6-1/4 36 12 35900 337J5 26620 25290
4-1/2 6-3/4 36 13 33200 31030 24500 23275
5 7-1/4 36 J4 30900 28900 22815 21670
5-1/4 7-7/8 36 15 28430 26580 20980 19810
5-1/2 8-3/8 36 16 26750 25000 19700 18630
6 9 25 J2 24900 23180 18300 17380
6-1/2 9-3/4 25 13 24000 22420 16900 16000
7 10-1/2 25 14 21350 19870 15685 14900
11-1/4 25 15 19900 18730 14790 14050
7 12 25 16 18690 17380 J3720 13040
ncnu7 nonucxz/on n/vD xnnnox/ xTE Dn/LLms DisTxncEs Hv /xc/JEs wiT/J 44-Tooli s/'RocxzT or uu/T FOR PLANTER EQUIPPED WITH 6.7015 TIRES TNFLASE D TO 24 PSI 0F AIR PRESSU RE ncnu7 nonucxz/on n/vD xnnnox/ xTE Dn/LLms DisTxncEs Hv /xc/JEs wiT/J 44-Tooli s/'RocxzT or uu/T FOR PLANTER EQUIPPED WITH 6.7015 TIRES TNFLASE D TO 24 PSI 0F AIR PRESSU RE ncnu7 nonucxz/on n/vD xnnnox/ xTE Dn/LLms DisTxncEs Hv /xc/JEs wiT/J 44-Tooli s/'RocxzT or uu/T FOR PLANTER EQUIPPED WITH 6.7015 TIRES TNFLASE D TO 24 PSI 0F AIR PRESSU RE ncnu7 nonucxz/on n/vD xnnnox/ xTE Dn/LLms DisTxncEs Hv /xc/JEs wiT/J 44-Tooli s/'RocxzT or uu/T FOR PLANTER EQUIPPED WITH 6.7015 TIRES TNFLASE D TO 24 PSI 0F AIR PRESSU RE ncnu7 nonucxz/on n/vD xnnnox/ xTE Dn/LLms DisTxncEs Hv /xc/JEs wiT/J 44-Tooli s/'RocxzT or uu/T FOR PLANTER EQUIPPED WITH 6.7015 TIRES TNFLASE D TO 24 PSI 0F AIR PRESSU RE ncnu7 nonucxz/on n/vD xnnnox/ xTE Dn/LLms DisTxncEs Hv /xc/JEs wiT/J 44-Tooli s/'RocxzT or uu/T FOR PLANTER EQUIPPED WITH 6.7015 TIRES TNFLASE D TO 24 PSI 0F AIR PRESSU RE ncnu7 nonucxz/on n/vD xnnnox/ xTE Dn/LLms DisTxncEs Hv /xc/JEs wiT/J 44-Tooli s/'RocxzT or uu/T FOR PLANTER EQUIPPED WITH 6.7015 TIRES TNFLASE D TO 24 PSI 0F AIR PRESSU RE ncnu7 nonucxz/on n/vD xnnnox/ xTE Dn/LLms DisTxncEs Hv /xc/JEs wiT/J 44-Tooli s/'RocxzT or uu/T FOR PLANTER EQUIPPED WITH 6.7015 TIRES TNFLASE D TO 24 PSI 0F AIR PRESSU RE
Maximum recommended speed (mph) Drilling distances (inohes) Sprocket combinations Sprocket combinations Plant populatlon Plant populatlon Plant populatlon Plant populatlon
Maximum recommended speed (mph) Drilling distances (inohes) (nmber of teeth) (nmber of teeth) Row width Row width Row width Row width
Maximum recommended speed (mph) Drilling distances (inohes) Driver Driven 28 30 38 40
5 7-5/8 36 12 28400 27590 21780 20690
5-1/2 8-1/4 36 13 27180 23710 19960 18970
6 9 36 14 24900 23180 18300 J7380
6-1/2 9-5/8 36 15 23280 2J670 17110 16260
7 10-1/4 36 16 21850 20230 15970 15170
7 11 25 12 20380 J8965 14970 14220
12 25 13 18650 17380 13720 13040
12-7/8 25 14 17400 16260 12810 12120
7 13-3/4 25 15 16280 15200 12000 11350
14-3/4 25 16 15200 14180 11800 10580
14
Opera tion 7 PRECISION FEED CUP The proper seed
guide must be used as shown for planting soybeans
or sorgh um. The same precision feed cup is used
for both applications but must be positioned as
shown for either soybeans or sorghum. Be certain
the selector gate is set at BEANS SO RG HUM
when using the precision feed cup.
Seed Guide for So y6eans
Feed Cuo lor So y6eans
When planting with the precision feed cup, disen-
gage the finger pic kup by removing cap screws
A." This allows the finger pic kup drive
sprocket to idle. Select the appropriate chart
and determine desired pounds per acre. The
sprocket combinations in the chart refer to the
stabilizer wheel driver sproc kets, NOT the
sprockets on the planting units.
ceed Guide lor Regular Ra te Sorgh um A tta
chment
Feed Cup lor Regular Ra te Sorgh um Attachment
15
Suggest If the above button click is invalid.
Please download this document first, and then
click the above link to download the complete
manual. Thank you so much for reading
16
8 Operation
PRECISION FEED CUP Continued Seed Spacing Charts
APPROXIMATE POUNDS OF SOYBEANS PER ACRE APPROXIMATE POUNDS OF SOYBEANS PER ACRE APPROXIMATE POUNDS OF SOYBEANS PER ACRE APPROXIMATE POUNDS OF SOYBEANS PER ACRE APPROXIMATE POUNDS OF SOYBEANS PER ACRE APPROXIMATE POUNDS OF SOYBEANS PER ACRE APPROXIMATE POUNDS OF SOYBEANS PER ACRE
Maximum recommended speed (mph) Sprocket combination Sprocket combination Pounds per acre Pounds per acre Pounds per acre Pounds per acre
Maximum recommended speed (mph) (number of teeth) Row width Row width Row width Row width
Maximum recommended speed (mph) Driver Driven 28 30 38 40
4 36 12 109 102 81 77
4-1/2 36 13 101 94 74 70
4-3/4 36 14 93 88 69 65
5 36 15 86 77 63 60
5-1/2 36 16 81 76 60 56
6 25 12 75 70 55 53
6-1/2 25 1.3 73 68 51 48
7 25 14 65 60 47 45
7 25 15 60 57 45 43
7 25 16 56 53 42 40
APPROXIMATE POUNDS OF SORGHUM PER ACRE - REGULAR RATE APPROXIMATE POUNDS OF SORGHUM PER ACRE - REGULAR RATE APPROXIMATE POUNDS OF SORGHUM PER ACRE - REGULAR RATE APPROXIMATE POUNDS OF SORGHUM PER ACRE - REGULAR RATE APPROXIMATE POUNDS OF SORGHUM PER ACRE - REGULAR RATE APPROXIMATE POUNDS OF SORGHUM PER ACRE - REGULAR RATE APPROXIMATE POUNDS OF SORGHUM PER ACRE - REGULAR RATE
Maximum recommended speed (mph) Sprocket combination Sprocket combination Pounds Pounds per acre per acre
Maximum recommended speed (mph) (number of teeth) (number of teeth) Row Row width width
Maximum recommended speed (mph) Driver Driven 38 40
4 36 12 19.4 18.2 14.4 13.1
4-1/2 36 13 17.9 16.7 13.2 12.0
4-3/4 36 14 16.7 15.6 12.3 11.8
5 36 15 15.3 14.3 11.3 10.7
5-1/2 36 16 14.4 13.5 10.6 10.0
6 25 12 13.5 12.5 9.9 9.4
6-1/2 25 13 13.0 12.1 9.1 8.6
7 25 14 11.5 10.7 8.5 8.1
7 25 15 10.7 10.1 7.9 7.5
7 25 16 10.0 9.3 7.4 7.0
17
https//www.ebooklibonline.com Hello dear
friend! Thank you very much for reading. Enter
the link into your browser. The full manual is
available for immediate download. https//www.ebo
oklibonline.com