New Holland 266 GMS Mid MountSide Discharge Mower Deck (Pin.YDWWL0001 and above) Operator’s Manual Instant Download (Publication No.47726367)

1
OPERATORS MANUAL
266GMS Mid Mount / Side Discharge Mower Deck PIN
YDWWL0001 and above
Part number 47726367 2nd edition English May
2014 Replaces part number 47486699
2
FRONT/BACK COVER (INSIDE AND OUTSIDE) SUPPLIED BY
NEW HOLLAND 266 GMS MOWER DECK PART NO.
47726367 DATE MAY 2014 AMEREQUIP 031615 (NHM610)
3
IMPORTANT SAFETY PRECAUTIONS UNDERSTAND SIGNAL
WORDS DANGER indicates a hazardous situation
which, if not avoided, will result in death or
serious injury. WARNING indicates a hazardous
situation which, if not avoided, could result in
death or serious injury. CAUTION indicates a
hazardous situation which, if not avoided may
result in minor or moderate injury. NOTICE is
used to address practices not related to physical
injury.

• SAFETY ALERT SYMBOL
• This is the safety alert symbol. It is used to
  alert you to potential physical injury hazards.
  Obey all safety messages that follow this symbol
  to avoid possible injury or death.
• In addition to the design and configuration of
  equipment, hazard control and accident prevention
  are dependent upon the awareness, concern,
  prudence and proper training of personnel in the
  operation, transport, maintenance and storage of
  equipment. Lack of attention to safety can result
  in accident, personal injury, reduction of
  efficiency and worst of all loss of life. Watch
  for safety hazards and correct deficiencies
  promptly. Use the following safety precautions as
  a general guide to safe operations when using
  this machine. Additional safety precautions are
  used throughout this manual for specific
  operating and maintenance procedures. Read this
  manual and review the safety precautions often
  until you know the limitations. Do not allow
  children or untrained persons to operate
  equipment. Do not operate equipment under the
  influence of drugs or alcohol.
• THE TRACTOR
• Read, understand and follow all instructions in
  the manual and on the machine before starting.
  Failure to do so could result in serious injury
  or death and equipment damage. Keep this manual
  in a safe place for future and regular reference
  and for ordering service parts.
• Read and understand all Safety Precautions in the
  Tractor Operators Manual.
• Allow only responsible operators familiar with
  the instructions to operate the machine. Know the
  controls and how
• to stop tractor engine and mower quickly in an
  emergency.
• Tractor must be equipped with Rollover Protective
  System (ROPS) and seat belt for all mower
  operations. Keep foldable ROPS systems locked in
  the up position at all times when operating the
  mower. Falling off or overturning a tractor can
  result in death from being run over or crushed.
• Always wear seat belt on Rollover Protective
  System (ROPS) equipped tractors. Do not wear a
  seat belt if the tractor
• Rollover Protective System (ROPS) has been
  removed.

4
https//www.ebooklibonline.com Hello dear
friend! Thank you very much for reading. Enter
the link into your browser. The full manual is
available for immediate download. https//www.ebo
oklibonline.com
5

• Tractor three point hitch components and hardware
  must be tightened to proper specifications to
  avoid damage to tractor or mower prior to
  operation. Please review tractor Operators
  Manual or consult your local dealer for proper
  torque and tightening specifications of tractor
  three point hitch components.
• Move and turn the tractor at low speeds. Avoid
  erratic operation and excessive speed.
• Keep the tractor in gear when traveling down
  hill.
• Do not mow near drop offs, ditches, or
  embankments. The tractor could suddenly over turn
  if a wheel travels over
• the edge of a ditch, or if an edge caves in.
• Add wheel ballast for stability when operating on
  slopes. Use extreme care when operating on slopes
  to maintain stability.
• Do not allow anyone but the operator on the
  tractor or mower. Never allow riders on tractor.
• Use extreme caution when loading or unloading the
  tractor and mower from a trailer or truck.
• THE MOWER
• Do not operate the mower unless it is rigidly
  attached to the tractor. Failure to do so could
  result in serious injury or

6

• Do not put hands or feet under the mower deck or
  near rotating parts.
• Always wear safety glasses with side shields or
  safety goggles during operation.
• Clear the area to be mowed of objects such as
  rocks, toys, wire, etc. which could be struck and
  thrown by the mower blades. A thrown object by
  the mower could travel in any direction and cause
  injury to the operator or a bystander. To help
  avoid injury, keep bystanders, children, and pets
  at least 75 feet from mower while in operation.
  Stop the mowing operation if anyone enters the
  area.
• Watch for hidden hazards in the area being cut
  during operation.
• Disengage the mower before shifting tractor into
  reverse and backing up. Always look down and
  behind before and while backing.
• Stop the mower blades when crossing gravel
  driveways, walks or roadways.
• Watch for traffic when operating near or crossing
  roadways.
• Never direct discharge towards people, pets or
  property.
• To avoid injury from thrown debris, never operate
  the mower when it is raised in the transport
  position.
• Never allow riders on tractor.

• WARNING Slopes are a major factor leading to
  loss of control and tip over accidents, which can
  result in severe injury or death. All slopes
  require extra caution. If slopes are greater than
  15 degrees, do not operate the mower on that area
  or serious injury or death could result.
• Add wheel ballast for stability when operating on
  slopes. Use extreme care when operating on slopes
  to maintain stability.
• Use extreme caution and reduce ground speed on
  slopes.
• Do not stop, start, or change directions suddenly
  on slopes. If the tractor tires lose traction,
  stop mower and proceed slowly straight down the
  slope.
• To prevent loss of control and overturning the
  tractor and mower, always mow up and down slopes,
  never across.
• Do not operate or transport on steep slopes.
• Do not mow on wet grass. Reduced traction could
  cause sliding on slopes.
• Keep the tractor in gear when traveling down
  hill.
• TRANSPORTATION

7

• Always use accessory lights and devices when
  transporting on a road or highway to warn
  operators of other vehicles.
• Check your local government regulations.
• Be sure the Slow Moving Vehicle (SMV) emblem is
  visible to the rear. If the SMV sign is worn,
  faded, or damage replace immediately.
• Use caution and reduce speed when transporting
  under adverse conditions, turning, or on
  inclines.
• Do not operate PTO during transport.
• MAINTENANCE
• Protect your eyes Wear Safety Glasses.
• Never run the tractor and mower inside a closed
  area. Engine exhaust fumes can be lethal.
• Always engage lift lockouts before servicing the
  mower.
• Before performing any service work make sure
  hoists, floor jacks, and jack stands are in good
  working order and are

damage to spindles, p
8
The safety of the operator was the prime
consideration in the design of the mower. Proper
shielding, convenient controls, simple
adjustments, and other safety features have been
built into this implement. The following decals
are located on the mower deck. Keep decals clean
and replace them immediately if they are missing
or damaged. Contact your dealer for replacements.
SAFETY DECALS
"A" HEIGHT OF CUT
"B" NO. OF HOLES
B
B
1" 1-3/4" 2-1/2" 3-1/4" 4"
4 3 2 1 0
A
SERIAL NUMBER INFORMATION A product
identification label is provided for your mower.
The numbers on this label are important if your
mower should require dealer service, or if you
need additional information on the equipment.
Prior to using the mower for the first time,
record the numbers from the identification label
in the appropriate spaces provided below. MODEL
NO. SERIAL NO.
CNH America LLC Racine, WI 53404 U.S.A. Made In
U.S.A.
Model Number
266GMS
Product Identification Number YDWWL0001
020357
020356
9

• IMPORTANT FEDERAL LAWS AND REGULATIONS
  CONCERNING EMPLOYERS, EMPLOYEES AND OPERATIONS.
• (This section is intended to explain in broad
  terms the concept and effect of the following
  federal laws and regulations. It is not intended
  as a legal interpretation of the laws and should
  not be considered as such).
• U.S. Public Law 91-596 (The Williams-Steiger
  Occupational and Health Act of 1970) OSHA
• This Act Seeks
• to assure so far as possible every working man
  and woman in the nation safe and healthful
  working conditions and
• to preserve our human resources
• DUTIES
• \Sec. 5(a) Each employer-
• shall furnish to each of his employees employment
  and a place of employment, which are free from
  recognized
• hazards that are causing or likely to cause death
  or serious physical harm to his employees
• shall comply with occupational safety and health
  standards promulgated under this Act.
• (b) Each employee shall comply with occupational
  safety and health standards and all rules,
  regulations and orders issued pursuant to this
  Act, which are applicable to his own actions and
  conduct.
• OSHA Regulations
• Current OSHA regulations state in part At the
  time of initial assignment and at least annually
  thereafter, the employer shall instruct every
  employee in the safe operation and servicing of
  all equipment with which the employee is, or will
  be involved. These will include (but are not
  limited to) instructions to

10
OPERATION
Blade sharpness will affect the appearance of the
area cut. Dull or damaged blades will cause the
grass to appear torn, rather than cut cleanly.
WARNING - Make sure Deflector Chute is installed
and correctly functioning to prevent injury.
Never operate mower with chute removed or raised
out of operating position.
Do not cut the grass too short. Short grass will
promote weed growth and yellows in dry weather.
Allow grass to grow longer in hot, dry
conditions. The additional length reduces heat
build-up, preserves needed moisture and
protects the grass from heat damage.
WARNING - To avoid injury never direct the
discharge of material towards bystanders or allow
anyone near the machine while in operation.
Mow often. Do not allow the grass to get too
tall. Mowing areas with tall grass may require
cutting at the maximum height as a first pass.
After completing the mowing operation at the
maximum height, the area can be recut with the
mower set at the desired height.
WARNING - To avoid injury and damage, re-torque
all fastening hardware, including blades and
spindle retaining hardware after the first hour
of operation.
At certain times of the year and under some
conditions, the mower may leave streaks of uncut
grass. The general cause is tall grass and
weeds. With this type of condition, it may be
necessary to make a second pass over the cut area
to get an even cut.
Safe operation of the tractor and mower is the
responsibility of the operator. Operator must be
familiar with tractor and mower controls and how
they function, and all Safety Precautions before
starting operation. The mower is designed as a
finish cut mower.
Cutting off too much at one time shocks the
plants growth system and weakens the grass
plants. A good guideline to follow is the 1/3
rule cut no more than one third of the grass
height, and never more than 1 inch at a time.
Do not allow anyone but the operator on the
tractor or mower. Never allow riders on tractor.
The mower is equipped with ground following front
caster wheels and rear gauge wheels, and is
designed to be operated with the wheels on the
ground. The deck cutting height is set by
positioning the right and left wheels in one of
five index hole settings. Refer to Cutting
Height Adjustment section of this manual for
proper adjustment.
Mow when the grass is 3 to 4 inches tall.
The time of day and condition of the grass will
affect the results you obtain when mowing. Mow at
the time of day when the grass is cool and dry.
Late afternoon or early evening will provide the
most ideal conditions. Do not mow when the grass
is wet or heavy with dew. Wet grass can build up
on the underside of the deck, creating an
imbalance through the blades and spindles,
causing possible damage to the mower deck belt.
Wet grass also leaves unsightly clumps on the
lawn.
The caster wheels on each side of the mower deck
can serve as a guide for mowing. When mowing,
position the mower deck such that the caster
wheel overlaps the edge of the grass previously
cut. This will assure full mower cut coverage.
Should the mower deck become plugged, raise deck,
shut off engine, set parking brake, and lock the
deck in the transport position.
Mowing should be performed with the tractor
engine operating at the recommended RPM. Do not
mow at high ground speed. Operating at
recommended RPM will insure proper blade speed
for effective cutting and discharge of grass from
the deck.
Clean the underside of the mower deck using
a scraper.
For best results, it is recommended that the
first two passes around the area to be mowed has
the discharge chute directed towards the center.
After the first two passes have been completed,
reverse direction to have the discharge chute
pointed outward. This will give a better
appearance to the lawn.
Operate the mower only in daylight or with
good artificial light.
11
ASSEMBLY
The mower deck has been partially disassembled
and secured to the shipping skid within the crate
assembly. Initial installation on the tractor
will require a hoist or other device capable of
safely lifting the entire mower deck assembly
from the shipping crate.
INSTALL CLEVIS PIN REAR GAUGE WHEEL
FULLY RAISED
NOTICE Tighten all hardware to torque
require- ments specified in torque chart at back
of manual.
1. Remove crate top and all straps securing deck
to crate sides. Remove crate sides.
2. Remove any miscellaneous items which have been
fastened to the mower deck or crating and arrange
conveniently. Remove strapping securing deck to
skid.
CAUTION Be sure hoist being used is suitable, has
sufficient capacity and is in the proper
position. Do not allow anyone under the mower
deck assembly support by hoist.
INSTALL CLEVIS PIN FRONT
GAUGE WHEEL FULLY RAISED
3. Raise and support deck assembly with hoist.
Remove crate skid from underneath deck assembly.
4. Remove retaining clips from clevis pins and
fully raise rear gauge wheels. Install clevis
pins in holes shown and secure with clips.
5. Remove retaining clips from clevis pins and
fully raise front caster wheels. Install clevis
pins in holes shown and secure with clips.
6. Carefully lower mower deck assembly to ground.
7. Proceed to the Attaching Kit Assembly
Instructions to complete the mower to tractor
installation. Check the installation carefully
and make sure that all components are correctly
installed and securely fastened.
12
MOWER DECK INSTALLATION TO TRACTOR
Install front linkage assembly to hooks at front
of mower deck.
NOTICE If there is access to an overhead hoist
with the proper lift rating, the operator has the
option of installing the deck to the tractor by
raising the front of the tractor and rolling the
mower deck rearward, under the tractor.
At front of tractor, pull out spring loaded J-Pin
located on left hand side of tractor. Raise front
linkage assembly into hooks on front latch.
Rotate handle weldment upward to secure assembly
into Front Hangers. Release J-Pin into hole on
Front Hanger and through hole in handle weldment.
NOTICE - Another option for installation is to
slide the mower deck into position from the right
hand side of tractor.
Pull back spring loaded J-Pins at back of deck.
Install lift assembly and secure using J-Pins.
Start tractor and turn front wheels fully left.
Shut off engine and remove key. Lower the mower
lift assembly using the three point hitch lever.
Install mower deck assembly from right hand side
of tractor. Move mower as necessary to guide the
gauge wheels and gear box past tractor components
Start tractor and turn front wheels straight
ahead. Shut off engine and remove key.
Raise and connect the mower drive shaft assembly
to the tractor mid-PTO.
Start tractor and raise deck assembly. Shut off
engine and remove key. Install lift lockout pins.
NOTICE - The most common method for installation
is to drive the tractor over the mower deck.
Remove Retaining Clips from Clevis Pins and
position rear Gauge Wheels to desired cut
setting. Refer to decal on mower deck or Mower
Cut Height Adjustment section in manual. Install
Clevis Pins in holes and secure with clips.
Begin the process by installing Ramp Kit
439047016 obtained from your local dealer.
Start tractor and place tractor in the lowest 4WD
gear possible. Carefully drive forward and align
front wheels with ramps. Proceed forward and
continue until deck is located between front and
rear wheels of tractor.
Remove Retaining Clips from Clevis Pins in front
Caster Wheels and position to desired cut
setting. Refer to decal on mower deck or Mower
Cut Height Adjustment section in manual. Install
Clevis Pins in holes and secure with clips.
Shut off engine and remove key. Remove ramps from
back of deck.
13
MOWER DECK REMOVAL FROM TRACTOR
Park the unit on a smooth hard surface. Raise
deck. Stop the engine. Set parking brake and
remove key.
INSTALL CLEVIS PIN REAR GAUGE WHEEL
FULLY RAISED
Remove Retaining Clips from Clevis Pins and
fully raise rear Gauge Wheels. Install Clevis
Pins in holes shown and secure with clips.
Remove Retaining Clips from Clevis Pins and
fully raise front Caster Wheels. Install Clevis
Pins in holes shown and secure with clips.
Lower the mower deck to the ground using the
three point hitch lever.
Disconnect the mower drive shaft assembly from
the tractor mid-PTO. Lower the drive shaft so it
rests securely on top of the deck.
Pull back spring loaded J-Pins at back of deck
to release from the lift assembly.
INSTALL CLEVIS PIN FRONT
GAUGE WHEEL FULLY RAISED
At front of tractor, pull out spring loaded J-Pin
located on left hand side of tractor. Rotate
handle weldment downward to release assembly from
Front Hangers.
Remove front linkage assembly from hook area at
front of mower deck.
NOTICE If there is access to an overhead hoist
with the proper lift rating, the operator has the
option of removing the deck from under the
tractor by raising the front of the tractor and
rolling the mower deck forward, from under the
tractor.
NOTICE - Another option for removal is to slide
the mower deck out from the right hand side of
tractor.
Start tractor and turn front wheels fully left.
Shut off engine and remove key.
Remove mower deck assembly from right hand side
of tractor. Move mower as necessary to guide the
gauge wheels and gear box past tractor components.
NOTICE - The most common method for removal is to
drive the tractor over the mower deck. Begin the
process by installing Ramp Kit from your local
dealer. Start tractor and place tractor in the
lowest 4WD reverse gear possible. Carefully back
up while aligning front wheels with ramp
created earlier. Proceed rearward and continue
until deck is located at front of tractor. Shut
off engine and remove key. Remove blocking
material from front and back of deck.
14
Suggest If the above button click is invalid.
Please download this document first, and then
click the above link to download the complete
manual. Thank you so much for reading
15
CUTTING HEIGHT ADJUSTMENT
The deck is to be operated with the front caster
wheels and rear gauge wheels on the ground. The
cutting height is set by positioning the right
and left wheels in one of five index hole
settings. The hole settings range in ¾
increments from a cutting height of approximately
1 inch (top hole) to 4 inches (bottom hole).
A HEIGHT OF CUT
B NO. OF HOLES
B
B
1 1-3/4 2-1/2 3-1/4 4
4 3 2 1 0
To adjust the height of cut, the gauge wheels are
adjusted as follows
Start the tractor and raise the mower deck by
raising the three point hitch lever. Set Parking
brake, shut off engine, and remove key.
A
WARNING Use caution when adjusting deck cutting
height. Install deck lift lock out pins and block
mower deck before proceeding with adjustment. The
mower decks weight is supported by the tractor
lift system. The deck could drop if the three
point lift lever is accidentally shifted. After
determining the desired cut height as shown in
the chart above, and on the mower deck itself,
adjust each wheel. Remove Wire Form Retainer and
Clevis Pin from deck bushing. Align the hole in
the wheel spindle with the hole in the deck
bushing and install Clevis Pin. Secure with Wire
Form Clip. Repeat process for other three wheel
spindles. NOTICE - Make sure the corresponding
height hole setting is used in all four wheels
settings.
13
16
https//www.ebooklibonline.com Hello dear
friend! Thank you very much for reading. Enter
the link into your browser. The full manual is
available for immediate download. https//www.ebo
oklibonline.com