BOBCAT 763 SKID STEER LOADER Service Repair Manual Instant Download ( SN 512440001 thru 512449999)

1
Service Manual
S/N 512212001 thru 512249999 S/N 512440001 thru
512449999 S/N 512612001 thru 512619999
HIGH FLOW
EQUIPPED WITH BOBCAT INTERLOCK CONTROL SYSTEM
(BICSTM)
6900091 (697)
Printed in U.S.A.
? Bobcat Company 1997
2
MAINTENANCE SAFETY
Instructions are necessary before operating or
servicing machine. Read and understand the
Operation Maintenance Manual, Operators
Handbook and signs (decals) on machine. Follow
warnings and instructions in the manuals when
making repairs, adjustments or servicing. Check
for correct function after adjustments, repairs
or service. Untrained operators and failure to
follow
WARNING
instructions can cause injury or death.
W-2003-0903
Safety Alert Symbol This symbol with a warning
statement, means Warning, be alert! Your safety
is involved! Carefully read the message that
follows. CORRECT CORRECT CORRECT
B-10731a
B-12365
B-7469
Never service the Bobcat Skid- Steer Loader
without instructions.
Use the correct procedure to lift or lower
operator cab.
Cleaning and maintenance are required daily.
WRONG
WRONG
WRONG
B-15231
B-11799
B-15280
Have good ventilation when welding or grinding
painted parts. Wear dust mask when grinding
painted parts. Toxic dust and gas can be
produced. Avoid exhaust fume leaks which can
kill without warning. Exhaust system must be
tightly sealed.
Disconnecting or loosening any hydraulic
tubeline, hose, fitting, component or a part
failure can cause lift arms to drop. Do not go
under lift arms when raised unless supported by
an approved lift arm support device. Replace it
if damaged.
Never work on loader with lift arms up unless
lift arms are held by an approved lift arm
support device. Replace if damaged. Never modify
equipment or add attachments not approved by
Bobcat Company.
WRONG
WRONG
WRONG
B-6590
B-6580
B-6589
Stop, cool and clean engine of flammable
materials before checking fluids. Never service
or adjust loader with the engine running unless
instructed to do so in the manual.
Keep body, jewelry and clothing away from moving
parts, electrical contact, hot parts and
exhaust. Wear eye protection to guard from
battery acid, compressed springs, fluids under
pressure and flying debris when engines are
running or tools are used. Use eye protection
approved for type of welding. Keep rear door
closed except for service. Close and latch door
before operating the loader.
Lead-acid batteries produce
flammable and explosive gases.
Keep arcs, sparks, flames and lighted tobacco
away from batteries. Batteries contain acid
which burns eyes or skin on contact. Wear
protective clothing. If acid contacts body,
flush well with water. For eye contact flush
well and get immediate medical attention.
Avoid contact with leaking
hydraulic fluid or diesel fuel
under pressure. It can penetrate the skin or
eyes. Never fill fuel tank with engine running,
while smoking or when near open flame.
Maintenance procedures which are given in the
Operation Maintenance Manual can be performed
by the owner/ operator without any specific
technical training. Maintenance procedures which
are not in the Operation Maintenance Manual
must be performed ONLY BY QUALIFIED BOBCAT
SERVICE PERSONNEL. Always use genuine Bobcat
replacement parts. The Service Safety Training
Course is available from your Bobcat
dealer. MSW01-0805
3
ALPHABETICAL INDEX
ACTUATORS . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . 101 ACTUATOR VOLTAGE
TEST . . . . . . . . . . . . . . . . . .
101 A.H.C. COMPONENTS . . . . . . . . . . . . .
. . . . . . . . . . 101 A.H.C./PWM CONTROLLER .
. . . . . . . . . . . . . . . . . 101 A.H.C.
HANDLE . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . 101 A.H.C. STEERING LEVER . . .
. . . . . . . . . . . . . . . . . 101 AIR
CLEANER . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . 71 AIR CLEANER SERVICE .
. . . . . . . . . . . . . . . . . . . . . 11
ALTERNATOR . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . 61 ALTERNATOR BELT . .
. . . . . . . . . . . . . . . . . . . . . . . .
11 AXLE SEAL . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . 41 AXLE,
SPROCKET AND BEARINGS . . . . . . . . . . . .
41 BATTERY . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . 61 BICS?
SYSTEM CONTROLLER . . . . . . . . . . . . . . . .
81 BICS VALVE . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . 21 BLOWER
HOUSING/FAN GEARBOX . . . . . . . . . . .
71 BOBCAT INTERLOCK CONTROL SYSTEM (BICS?) . . .
. . . . . . . . . 81, 101 BOBTACH . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
11, 51
LIFT ARM SUPPORT DEVICE . . . . . . . . . . . . .
. . . . . . 11 LIFT ARMS . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
51 LIFT CYLINDER(S) . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . 21 LIFT LOCK
BYPASS VALVE . . . . . . . . . . . . . . . . . .
. . 21 LIFTING AND BLOCKING THE LOADER . . . .
. . . . . 11 LIFTING THE LOADER . . . . . . . .
. . . . . . . . . . . . . . . . . 11 LOADER
SPECIFICATIONS 763 . . . . . . . . . . . . . .
. 91 LUBRICATING THE LOADER . . . . . . . . . .
. . . . . . . . . 11 MONITOR SERVICE CODES . . .
. . . . . . . . . . . . . . . . . 81 MOTOR
CARRIER . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . 41 OIL COOLER . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
31 OIL PUMP . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . 71 OPERATOR
CAB . . . . . . . . . . . . . . . . . . . . . . .
. . 11, 51 OPERATOR CAB GAS CYLINDER . . . . .
. . . . . . . . . . 51 OPERATOR SEAT . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
51 PARKING BRAKE . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . 41 PARKING BRAKE
DISC . . . . . . . . . . . . . . . . . . . . . .
. . 41 PEDAL INTERLOCK LINKAGE . . . . . . . . .
. . . . . . . . . 21 PISTON AND CONNECTING ROD .
. . . . . . . . . . . . . . 71 RADIATOR . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . 71 REAR DOOR . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . .
51 REAR GRILL . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . 51 REAR LIGHTS
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . 51 RELAY SWITCHES . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
61 REMOTE START SWITCH . . . . . . . . . . . . .
. . . . . . . . . 11 ROCKER ARM AND SHAFT . . .
. . . . . . . . . . . . . . . . . . 71 RPM
SENSOR . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . 81 SEAT BAR
(W/COMPRESSION SPRINGS) . . . . . . . 51 SEAT
BAR (W/GAS CYLINDER) . . . . . . . . . . . . . .
. . . 51 SEAT BAR RESTRAINT SYSTEM . . . . . . .
. . . . . . . . . 11 SEAT BAR SENSOR . . . . .
. . . . . . . . . . . . . . . . . . . . . .
81 SEAT SENSOR . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . 81 SELECT VALVE
(763H) . . . . . . . . . . . . . . . . . . . . .
. . . . 21 SENDER AND SENSOR . . . . . . . . . .
. . . . . . . . . . . . . . 81 SERVICE SCHEDULE
. . . . . . . . . . . . . . . . . . . . . . . . .
. 11 SPARK ARRESTOR MUFFLER . . . . . . . . . .
. . . . . . . . 11 SPRING LOADED DRIVE BELT
TENSIONER PULLEY . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
31 STANDARD INSTRUMENT PANEL . . . . . . . . . .
. . . . . 61 STANDARD TORQUE SPECIFICATIONS FOR
BOLTS . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . 91 STARTER (DELCO REMY)
. . . . . . . . . . . . . . . . . . . . . .
61 STARTER (DENSO) . . . . . . . . . . . . . . .
. . . . . . . . . . . . . 61 STEERING LINKAGE .
. . . . . . . . . . . . . . . . . . . . . . . . .
. 31 SWITCH HANDLE . . . . . . . . . . . . . . .
. . . . . . . . . . . . . 101 STOPPING THE
BOBCAT LOADER . . . . . . . . . . . . . .
11 TILT LOCK VALVE . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . 21 TILT CYLINDER . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . 21 TIMING GEARS . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . 71 TIMING
GEARCASE COVER . . . . . . . . . . . . . . . . .
. . . 71 TIRE MAINTENANCE . . . . . . . . . . .
. . . . . . . . . . . . . . . 11 TORQUE
SPECIFICATIONS FOR LOADER . . . . . . . 91
TOWING THE LOADER . . . . . . . . . . . . . . . .
. . . . . . . . 11 TRACTION LOCK . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . .
81 TRACTION LOCK GUIDES . . . . . . . . . . . .
. . . . . . . . . . 41 TRANSPORTING THE LOADER .
. . . . . . . . . . . . . . . .
11 TROUBLESHOOTING . . . . . . . 21, 31, 61,
71, 101 TROUBLESHOOTING THE BOSS? L.C.D.
DISPLAY . . . . . . . . . . . . . . . . 81 U.S.
TO METRIC CONVERSION . . . . . . . . . . . . . .
. . . 91 VALVE, VALVE SEAT AND GUIDE . . . . .
. . . . . . . . . . 71 WATER PUMP . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. 71
BOSS? DIAGNOSTIC TOOL . . . . . . . . . . . . . .
. . . . . 81
BOSS? INSTRUMENT PANEL . . . . . . . . . . . . .
. . . . 81 CHAINCASE COVERS . . . . . . . . . .
. . . . . . . . . . . . . . 41 CHAINCASE FLUID .
. . . . . . . . . . . . . . . . . . . . . . . . .
. 41 CONTROL PANEL . . . . . . . . . . . . . . .
. . . . . . . . . . . . . 31 CONTROL PEDALS . .
. . . . . . . . . . . . . . . . . . . . . . . . .
21 CRANKSHAFT AND BEARINGS . . . . . . . . . .
. . . . . . 71 CRANKSHAFT GEAR . . . . . . . .
. . . . . . . . . . . . . . . . . 71 CYLINDER
BORE . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . 71 CYLINDER HEAD . . . . . . . . .
. . . . . . . . . . . . . . . . . . . .
71 DECIMAL MILLIMETER EQUIVALENTS . . . . . .
. 91 DRIVE BELT . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . 11 DRIVE BELT
HOUSING . . . . . . . . . . . . . . . . . . . . .
. . . 31 DRIVE CHAIN . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . .
41 ELECTRICAL/HYDRAULIC (CONTROL REF.) . . . .
81 ELECTRICAL SYSTEM INFORMATION . . . . . . .
. . 61 ENGINE . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 71
ENGINE COMPRESSION . . . . . . . . . . . . . . .
. . . . . . . 71 ENGINE COOLING SYSTEM . . . . .
. . . . . . . . . . . . . . 11 ENGINE
LUBRICATION SYSTEM . . . . . . . . . . . . . . .
11 ENGINE MUFFLER . . . . . . . . . . . . . . .
. . . . . . . . . . . . 71 ENGINE SPECIFICATIONS
. . . . . . . . . . . . . . . . . . . .
91 ENGINE SPEED CONTROL . . . . . . . . . . . .
. . . . . . . . 71 FAN GEARBOX . . . . . . . . .
. . . . . . . . . . . . . . . . . . 11, 71
FINAL DRIVE TRANSMISSION (CHAINCASE) . . . 11
FIXED DRIVE BELT TENSIONER PULLEY . . . . . . .
31 FLYWHEEL . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . 71 FRONT LIGHTS
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . 61 FUEL CAMSHAFT . . . . . . . . . . .
. . . . . . . . . . . . . . . . . 71 FUEL
INJECTION NOZZLES . . . . . . . . . . . . . . . .
. . . 71 FUEL INJECTION PUMP . . . . . . . . . .
. . . . . . . . . . . . 71 FUEL SYSTEM . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. 11 FUEL TANK . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . 51 GLOW PLUGS
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . 71 HANDLE CONTROL UNIT . . . . .
. . . . . . . . . . . . . . . 101 HYDRAULIC
CONTROL VALVE . . . . . . . . . . . . . . . .
21 HYDRAULIC CONTROL VALVE (AHC) . . . . . . . .
. 101 HYDRAULIC CYLINDER IDENTIFICATION . . . .
. . . 21 HYDRAULIC CYLINDERS . . . . . . . . .
. . . . . . . . . . . . . 21 HYDRAULIC FILTER
HOUSING . . . . . . . . . . . . . . . .
21 HYDRAULIC FLUID RESERVOIR . . . . . . . . . .
. . . . . 21 HYDRAULIC/HYDROSTATIC FLUID
SPECIFICATIONS . . . . . . . . . . . . . . . . .
. . . . 91 HYDRAULIC/HYDROSTATIC SYSTEM . . . .
. . . . . . 11 HYDRAULIC PUMP . . . . . . . . .
. . . . . . . . . . . . . . . . . . 21
HYDRAULIC SYSTEM INFORMATION . . . . . . . . . .
91 HYDROSTATIC DRIVE MOTOR . . . . . . . . . .
. . . . . . 31 HYDROSTATIC DRIVE MOTOR 30
SERIES . . . . . . 31 HYDROSTATIC PUMP . . . .
. . . . . . . . . . . . . . . . . . . . . 31
HYDROSTATIC SYSTEM INFORMATION . . . . . . . .
31 IDLER GEAR AND CAMSHAFT . . . . . . . . . . .
. . . . . . 71 Revised Jan. 99
4
https//www.ebooklibonline.com Hello dear
friend! Thank you very much for reading. Enter
the link into your browser. The full manual is
available for immediate download. https//www.eb
ooklibonline.com
5
CONTENTS
PREVENTIVE MAINTENANCE
FOREWORD . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . ii SAFETY INSTRUCTIONS . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . v SERIAL NUMBER
LOCATIONS . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . vii DELIVERY
REPORT . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
vii BOBCAT LOADER IDENTIFICATION . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
viii PREVENTIVE MAINTENANCE . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
11 HYDRAULIC SYSTEM . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . 21 HYDROSTATIC SYSTEM . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . 31 DRIVE SYSTEM . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . 41 MAIN FRAME .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
51 ELECTRICAL SYSTEM . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . 61 ENGINE SERVICE . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . 71 SYSTEMS ANALYSIS . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
81 SPECIFICATIONS . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . 91 ADVANCED HAND CONTROL SYSTEM
. . . . . . . . . . . . . . . . . . . . . . . . .
. 101
HYDRAULIC SYSTEM
HYDROSTATIC SYSTEM
DRIVE SYSTEM
CALIFORNIA PROPOSITION 65 WARNING Diesel engine
exhaust and some of its constituents are known to
the State of California to cause cancer, birth
defects and other reproductive harm.
MAIN FRAME
ELECTRICAL SYSTEM
ENGINE SERVICE
SYSTEMS ANALYSIS
SPECIFICATIONS
ADVANCED HAND CONTROL SYSTEM
763/763H BICS Loader Service Manual
i
6
FOREWORD This manual is for the Bobcat loader
mechanic. It provides necessary servicing and
adjustment procedures for the Bobcat loader and
its component parts and systems. Refer to the
Operation Maintenance Manual for operating
instructions, starting procedure, daily checks,
etc. A general inspection of the following items
must be made after the loader has had service or
repair
1. Check that the ROPS/FOPS (Including
sidescreens) is in good condition and is not
modified.
9. The parking brake must function correctly.
2. Check that ROPS mounting hardware is
tightened and is Melroe approved.
10. Enclosure door latches must open and close
freely.
3. The seat belt must be correctly installed,
functional and in good condition.
11. BobTach wedges and
linkages must function
correctly and be in good condition.
4. The seat bar and pedal
12. Safety treads must in good condition.
interlocks must be correctly adjusted, clean and
lubricated.
5. Check lift arm support device, replace if
damaged.
13. Check for correct function of indicator
lamps (Optional on some models).
6. Machine signs must be legible and in the
correct location.
14. Check hydraulic fluid level, engine oil
level and fuel supply.
WARNING
7. Steering levers and foot pedals must return
to neutral.
15. Inspect for fuel, oil or hydraulic fluid
leaks.
8. Check for correct function of the work lights.
16. Lubricate the loader.
763/763H BICS Loader Service Manual
iii
Revised Jan. 99
7
17. Check the condition of the battery and
cables.
18. Inspect the air cleaner for damage or leaks.
Check the condition of the element.
19. Check the electrical charging system.
20. Check tires for wear and pressure.
21. Inspect for loose or broken parts or
connections.
22. Operate the loader and check all functions.
23. Check for any field modification not
completed.
24. Check for correct function of the Bobcat
Interlock Control System (BICS?) before the
machine is returned to the customer. Recommend
to the owner that all necessary corrections be
made before the machine is returned to service.
763/763H BICS Loader Service Manual
iv
Revised Jan. 99
8
SAFETY INSTRUCTIONS

• Instructions are necessary before operating or
  servicing machine. Read and understand the
  Operation Maintenance Manual, Handbook and
  signs (decals) on machine. Follow warnings and
  instructions in the manuals when making repairs,
  adjustments or servicing. Check for correct
  function after adjustments, repairs or service.
  Untrained operators and failure to follow
  instructions can cause injury or death.
• W20030199
• The following publications provide information on
  the safe use and maintenance of the loader and
  attachments
• The Delivery Report is used to assure that
  complete instructions have been given to the new
  owner and that the machine is in safe operating
  condition.
• The Operation Maintenance Manual delivered with
  the loader gives operating information as well as
  routine maintenance and service procedures. It
  is a part of the loader and must stay with the
  machine when it is sold. Replacement Operation
  Maintenance Manuals can be ordered from your
  Bobcat loader dealer.
• The loader has machine signs (decals) which
  instruct on the safe operation and care. The
  signs and their locations are shown in the
  Operation Maintenance Manual. Replacement signs
  are available from your Bobcat loader dealer.
• The loader has a plastic Operators Handbook
  fastened to the operator cab. Its brief
  instructions are convenient to the operator. The
  Handbook is available from your dealer in an
  English edition or one of many other languages.
  See your Bobcat dealer for more information on
  translated versions.
• The EMI Safety Manual (available in Spanish)
  delivered with the loader gives general safety
  information.
• The Service Manual and Parts Manual are available
  from your dealer for use by mechanics to do
  shoptype service and repair work.
• The SkidSteer Loader Operator Training Course is
  available through your local dealer. This course
  is intended to provide rules and practices for
  correct operation of the Bobcat loader. The
  course is available in English and Spanish
  version.
• The Service Safety Training Course is available
  from your Bobcat dealer. This course provides
  information for safe and correct service
  procedures for Bobcat SkidSteer loaders.
• The Bobcat SkidSteer Loader Safety Video is
  available from your Bobcat Dealer.

This notice identifies procedures which
must be followed to avoid damage to the
machine. I20190284
Warnings on the machine and in the manuals are
for your safety. Failure to obey warnings can
cause injury or
death.
W20441285
Safety Alert Symbol This symbol with a warning
statement, means Warning, be alert! Your safety
is involved! Carefully read the message that
follows.
SIO50299
763/763H BICS Loader Service Manual
v
Revised Jan. 02
9

• FIRE PREVENTION
• The loader has several components that are at
  high temperature under normal operating
  conditions. The primary source of high
  temperatures is the engine and exhaust system.
  The electrical system, if damaged or incorrectly
  maintained, can be a source of arcs or sparks.
• Flammable debris (leaves, straw, etc.) must be
  removed regularly. If flammable debris is allowed
  to accumulate, it will increase the fire hazard.
  The loader must be cleaned as often as necessary
  to avoid this accumulation. Flammable debris in
  the engine compartment is a fire hazard when the
  loader is parked with a hot engine.
• The spark arrestor muffler is designed to control
  the emission of hot particles from the engine and
  exhaust system, but the muffler and the exhaust
  gases are still hot.
• Do not use the Bobcat loader where exhaust, arcs,
  sparks or hot components can contact flammable
  material, explosive dust or gases.
• The engine compartment and engine cooling system
  must be inspected every day and cleaned if
  necessary to prevent fire hazard and
  overheating.
• Check all electrical wiring and connections for
  damage. Keep the battery terminals clean and
  tight. Repair or replace any damaged part.
• Check fuel and hydraulic tubes, hoses and
  fittings for damage and leakage. Never use open
  flame or bare skin to check for leaks. Tighten
  or replace any parts that show leakage. Always
  clean fluid spills. Do not use gasoline or diesel
  fuel for cleaning parts. Use commercial
  nonflammable solvents.
• Do not use ether or starting fluids on this
  engine. It has glow plugs. These starting aids
  can cause explosion and injure you or
  bystanders.
• Always clean the loader and disconnect the
  battery before doing any welding. Cover rubber
  hoses, battery and all other flammable parts.
  Keep a fire extinguisher near the loader when
  welding. Have good ventilation when grinding or
  welding painted parts. Wear dust mask when
  grinding painted parts. Toxic dust or gas can be
  produced.
• Stop the engine and let it cool before adding
  fuel. No smoking!
• Use the procedure in the Operation Maintenance
  Manual for connecting the battery.
• Use the procedure in the Operation Maintenance
  Manual for cleaning the spark arrestor muffler.
• Know where fire extinguishers and first aid kits
  are located and how to use them.
• A fire extinguisher is available from your Bobcat
  dealer. The fire extinguisher can be installed in
  the location shown A.

A

P10650
SI060301
763/763H BICS Loader Service Manual
vi
Revised Jan. 02
10
SERIAL NUMBER LOCATIONS Always use the serial
number of the loader when requesting service
information or when ordering parts. Early or
later models (identification made by serial
number) may use different parts, or it may be
necessary to use a different procedure in doing
a specific service operation. LOADER SERIAL
NUMBER The loader serial number plate is located
on the loader frame as shown A. Explanation of
loader Serial Number XXXX XXXXX Module 2.
Production Sequence (Series) Module 1.
Model/Engine Combination The four digit
Model/Engine Combination module number
identifies the model number and engine
combination. The five digit Production Sequence
Number identifies the order which the loader is
produced. ENGINE SERIAL NUMBER The serial number
is located on the valve cover at the the right
side of the engine B.
A

P05082
B

P04314
C
DELIVERY REPORT The Delivery Report must be
filled out by the dealer and signed by the owner
or operator when the Bobcat loader is delivered.
An explanation of the form must be given to the
owner. Make sure it is filled out completely C.
763/763H BICS Loader Service Manual
vii
Revised Jan. 02
11
BOBCAT LOADER IDENTIFICATION
FRONT LIGHTS GRAB OPERATOR SEAT HANDLES STEERING LEVER SEAT BELT TILT CYLINDER ? REAR AUXILIARY QUICK COUPLERS BUCKET FRONT AUXILIARY QUICK COUPLERS SAFETY TREAD STEPS OPERATOR CAB (ROPS FOPS) REAR WINDOW SEAT BAR REAR GRILL LIFT ARM LIFT ARM SUPPORT DEVICE LIFT CYLINDER REAR LIGHT TAIL LIGHT TIRES REAR DOOR FRONT LIGHTS GRAB OPERATOR SEAT HANDLES STEERING LEVER SEAT BELT TILT CYLINDER ? REAR AUXILIARY QUICK COUPLERS BUCKET FRONT AUXILIARY QUICK COUPLERS SAFETY TREAD STEPS OPERATOR CAB (ROPS FOPS) REAR WINDOW SEAT BAR REAR GRILL LIFT ARM LIFT ARM SUPPORT DEVICE LIFT CYLINDER REAR LIGHT TAIL LIGHT TIRES REAR DOOR
B15010 B15011

• OPTIONAL OR FIELD ACCESSORY (Not Standard
  Equipment)
• TIRES Flotation tires (optional) are shown.
  The Bobcat loader is factory equipped with
  standard tires.
• BUCKET Several different buckets and other
  attachments are available for the Bobcat loader.
• ROPS, FOPS Roll Over Protective Structure,
  Falling Object Protective Structure, per SAE
  J1040 and ISO 3471, and Falling Object
  Protective Structure per SAE J1043 and ISO 3449,
  Level l. Level ll is available. The Bobcat
  loader is baseequipped with a standard operator
  cab as shown. Extra insulated cab is available as
  an option (Reduced noise level).
• 763/763H BICS Loader

viii Service Manual
Revised Jan. 02
12
PREVENTIVE MAINTENANCE
PREVENTIVE MAINTENANCE
Page Number
AIR CLEANER SERVICE Replacing Filter Element . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . 115 ALTERNATOR
BELT Adjusting The Alternator Belt . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . 123 BOBTACH Inspection And Maintenance .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 136 DRIVE BELT Adjusting The
Drive Belt Equipped With The Fixed Drive Idler .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . 132 Adjusting The
Drive Belt Equipped With The Spring Loaded Drive
Idler . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . 130 Drive Belt Replacement
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . 133 ENGINE COOLING
SYSTEM Cleaning The Cooling System . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . 121 Checking The Coolant Level . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . 121 Replacing The Coolant . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . 122 ENGINE LUBRICATION
SYSTEM Checking Engine Oil . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . 119 Replacing Oil And Filter . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . 119 FAN GEARBOX Checking
And Maintaining . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
123 FINAL DRIVE TRANSMISSION (CHAINCASE) Checking
And Adding Oil . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . .
129 Removing Oil From The Chaincase . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
129 FUEL SYSTEM Filling the Fuel Tank . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . 117 Fuel Filter . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
117 Fuel Specifications . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . 117 Removing Air From The Fuel
System . . . . . . . . . . . . . . . . . . . . .
. . . . . . . 118 HYDRAULIC/HYDROSTATIC
SYSTEM Checking And Adding Fluid . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . 124 Replacing Hydraulic/Hydrostatic
Filter . . . . . . . . . . . . . . . . . . . . .
. . . . . . . 124 Hydraulic Reservoir Breather
Cap . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . 126 Replacing Hydraulic Fluid .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . 125 LIFT ARM SUPPORT
DEVICE Disengaging The Lift Arm Support Device .
. . . . . . . . . . . . . . . . . . . . . . .
18 Engaging The Lift Arm Support Device . . . .
. . . . . . . . . . . . . . . . . . . . . . . 17
Continued On Next Page
763/763H BICS Loader Service Manual
11
Revised Jan. 02
13
PREVENTIVE MAINTENANCE (Contd) Page
Number LIFTING AND BLOCKING THE LOADER Procedure
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . 14 LIFTING THE LOADER Single Point Lift . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . .
16 LUBRICATION OF THE LOADER Procedure . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . .
134 OPERATOR CAB Description . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . 19 Lowering The
Operator Cab . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . 111 Raising
The Operator Cab . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . .
19 Emergency Exit . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . 19 REMOTE START SWITCH Procedure .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. 137 SEAT BAR RESTRAINT SYSTEM (ADVANCED HAND
CONTROLS) Description . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . 114 Seat Bar
Inspection . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
114 Seat Bar Maintenance . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . 114 SEAT BAR RESTRAINT SYSTEM
(MECHANICAL HAND CONTROLS) Description . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
113 Seat Bar Inspection . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . 113 Seat Bar Maintenance . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 113 SEAT BAR RESTRAINT
SYSTEM (FOOT PEDALS) Description . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . 112 Seat Bar
Inspection . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
112 Seat Bar Maintenance . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . 112 SERVICE SCHEDULE Chart . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
13 SPARK ARRESTOR MUFFLER Cleaning Procedure . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . 127 STOPPING THE
BOBCAT LOADER . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . 15 TIRE
MAINTENANCE Tire Mounting . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . 128 Tire Rotation . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . .
128 Wheel Nuts . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . 128 TOWING THE
LOADER Procedure . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . 15 TRANSPORTING THE
LOADER Procedure . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . 15
763/763H BICS Loader Service Manual
Revised Jan. 02
12
14
SERVICE SCHEDULE Maintenance work must be done at
regular intervals. Failure to do so will result
in excessive wear and early failures. The
service schedule is a guide for correct
maintenance of the Bobcat loader. Instructions
are necessary before operating or servicing
machine. Read and understand the Operation
Maintenance Manual, Handbook and signs (decals)
on machine. Follow warnings and instructions in
the manuals when making repairs, adjustments or
servicing. Check for correct function after
adjustments, repairs or service. Untrained
operators and failure to follow instructions can
cause injury or death.
W20030199

ITEM SERVICE REQUIRED SERVICE REQUIRED 810 50 100
ITEM SERVICE REQUIRED SERVICE REQUIRED 810 50 100 250 250 250 500 500 500 1000 1000 1000
Engine Oil Check the oil level and add oil as needed. Check the oil level and add oil as needed.
Engine Air Filter and Air System Check condition indicator or display panel. Service only when required. Check for leaks and damaged components. Check condition indicator or display panel. Service only when required. Check for leaks and damaged components.
Engine Cooling System Clean debris from oil cooler, radiator and grill. Check coolant level in recovery tank (engine cold). Add coolant as needed. Clean debris from oil cooler, radiator and grill. Check coolant level in recovery tank (engine cold). Add coolant as needed.
Tires Check for damaged tires and correct air pressure. Check for damaged tires and correct air pressure.
Seat Belt, Seat Bar, Foot Pedal or Hand Control Interlocks Check the condition of seat belt. Check the seat bar, and foot pedal interlocks or hand control interlocks. Clean dirt and debris from moving parts. Check the condition of seat belt. Check the seat bar, and foot pedal interlocks or hand control interlocks. Clean dirt and debris from moving parts.
Safety Signs and Safety Tread Check for damaged signs (decals) and safety tread. Replace any signs or safety treads that are damaged or worn. Check for damaged signs (decals) and safety tread. Replace any signs or safety treads that are damaged or worn.
Indicators Lights (Opt.) Check for correct operation of all indicators lights. Check for correct operation of all indicators lights.
Operator Cab Check the fastening bolts, washers nuts. Check the condition of cab. Check the fastening bolts, washers nuts. Check the condition of cab.
Lift Arms, Cyl., BobTach Pivot Pins and Wedges Lubricate with multipurpose lithium based grease. Lubricate with multipurpose lithium based grease.
Fuel Filter Remove the trapped water. Remove the trapped water.
Bobcat Interlock Control System (BICSTM) Check BICSTM functions. Clean dirt, debris or objects from under and behind seat and around brake pedal as required. Check BICSTM functions. Clean dirt, debris or objects from under and behind seat and around brake pedal as required.
Hydraulic Fluid, Hoses and Tubelines Check fluid level and add as needed. Check for damage and leaks. Repair or replace as needed. Check fluid level and add as needed. Check for damage and leaks. Repair or replace as needed.
Final Drive Trans.(Chaincase) Check oil level. Check oil level.
Foot Pedals, Hand Controls, and Steering Levers Check for correct operation. Repair or adjust as needed. Check for correct operation. Repair or adjust as needed.
Wheel Nuts Check for loose wheel nuts and tighten to 105115 ft.lbs. (142156 Nm) torque. Check for loose wheel nuts and tighten to 105115 ft.lbs. (142156 Nm) torque.
Parking Brake Check operation. Check operation.
Spark Arrestor Muffler Clean the spark chamber. Clean the spark chamber.
Battery Check cables, connections and electrolyte level. Add distilled water as needed Check cables, connections and electrolyte level. Add distilled water as needed
Steering Shaft Grease two fittings. Grease two fittings.
Engine/Hydros. Drive Belt Check for wear or damage. Adjust as needed. Check for wear or damage. Adjust as needed.
Fan Drive Gearbox Check gear lube level. Add as needed. Check gear lube level. Add as needed.
Alternator Belt Check belt tension and adjust as needed. Check belt tension and adjust as needed.
Engine Oil and Filter Replace oil and filter. Use CD or better grade oil and Bobcat filter.
Fuel Filter Replace the filter element. Replace the filter element.
Hydraulic Reservoir Breather Cap Replace the reservoir breather cap. Replace the reservoir breather cap.
Hydraulic Reservoir Replace the fluid. Replace the fluid.
Final Drive Trans.(Chaincase) Replace the fluid. Replace the fluid.
Hydraulic/Hydrostatic Filter Replace the filter element. Replace the filter element.
Case Drain Filters Replace the filters. Replace the filters.
Bobcat Interlock Control System (BICSTM) Check lift arm bypass control Check lift arm bypass control
Check wheel nut torque every 8 hours for the
first 24 hours. Replace filter element after the
first 50 hours and when the transmission warning
light comes ON. Or every 12 months. Inspect
the new belt after first 50 hours. First oil and
filter change must occur at 50 hours 250 hours
thereafter. 763/763H BICS Loader
Revised Jan. 02
13 Service Manual
15
A

B07023
Instructions are necessary before operating or
servicing machine. Read and understand the
Operation Maintenance Manual, Handbook and
signs (decals) on machine. Follow warnings and
instructions in the manuals when making repairs,
adjustments or servicing. Check for correct
function after adjustments, repairs or service.
Untrained operators and failure to follow
instructions can cause injury
or death A.
W20030199
LIFTING AND BLOCKING THE LOADER Procedure Always
park the loader on a level surface.
Put jackstands under the front axles and rear
corners of the frame before running the engine
for service. Failure to use jackstands can allow
the machine to fall or move and cause injury
or death. W20170286 Put the floor jack under
the rear of the loader B. Lift the rear of the
loader and install jackstands B.
B

P03869
Put the floor jack under the front the loader
C. Lift the front of the loader and put
jackstands under the axle tubes C. NOTE Make
sure the jackstands do not touch the tires.
C

P03868
763/763H BICS Loader Service Manual
Revised Jan. 02
14
16
TRANSPORTING THE BOBCAT LOADER
A
SUPPORT SUPPORT SUPPORT
MC01241
Adequately designed ramps of sufficient strength
are needed to support the weight of the machine
when loading onto a transport vehicle. Wood
ramps can break and cause
personal injury.
W20580494
When a loader has an empty bucket or no
attachment, always drive backward onto the
transport vehicle A. The rear of the trailer
must be blocked or supported A when loading or
unloading the loader to prevent the front end of
the trailer from raising up. Be sure the
transport and towing vehicles are of adequate
size and capacity.
B
Use the following procedure to fasten the Bobcat
loader to the transport vehicle to prevent the
loader from moving during sudden stops or when
going up or down slopes B.

• Lower the bucket or attachment to the floor.
• Stop the engine.
• Engage the parking brake.
• Install chains at the front and rear loader tie
  down positions (Inset) B.
• Fasten each end of the chain to the transport
  vehicle.
• TOWING THE LOADER
• To prevent damage to the loaders hydrostatic
  system, tow the loader only a short distance at
  slow speed. (Example Moving the loader onto a
  transport vehicle).
• The towing chain (or cable) must be rated at 1
  1/2 times the weight of the loader. (See
  SPECIFICATIONS Page 91.)
• Turn the key switch to ON and press the traction
  lock override button.
• Tow the Bobcat at 2 MPH (3,2 km/hr) or less for
  not more than 25 feet (7,6 meters).
• If the electrical system is not functioning,
  contact your Bobcat loader dealer. (Part of the
  brake system must be disassembled to move the
  loader.)

P05090
P05077
MC01242
6707867
STOPPING THE BOBCAT LOADER Move the steering
levers to the neutral position. The hydrostatic
transmission will act as a service brake to stop
the loader.
763/763H BICS Loader Service Manual
15
Revised Jan. 02
17
LIFTING THE LOADER Single Point Lift
A

MC02366

• AVOID INJURY OR DEATH
• Before lifting, check fasteners on single point
  lift and operator cab.
• Assemble front cab fasteners as shown in this
  manual.
• Never allow riders in the cab or bystanders
• within 15 feet (5 meters) while lifting the
  machine.
• W20070497
• Lift the loader with the single point lift which
  is available as a kit from your Bobcat loader
  dealer.
• Attach cables or chains to the single point lift
  as shown
• A.
• The single point lift, supplied by Bobcat Company
  is designed to lift and support the Bobcat
  loader without affecting roll over and falling
  object protection features of the operator cab.

763/763H BICS Loader Service Manual
16
Revised Jan. 02
18
LIFT ARM SUPPORT DEVICE
A
2 1 2 1 2 1
P03923
B
1 1 1
P03927
Never work on a machine with the lift arms up
unless the lift arms are secured by an approved
lift arm support device. Failure to use an
approved lift arm support device can allow the
lift arms or attachment to fall and cause injury
or death. W20590598
Engaging The Lift Arm Support Device Maintenance
and service work can be done with the lift arms
lowered. If the lift arms must be raised for
service, use the following procedure Put
jackstands under the rear corners of the
loader. Disconnect the spring from the lift arm
support device retaining pin (Item 1) A, hold
onto the lift arm support device (Item 2) A
and remove the retaining pin. Lower the lift arm
support device on top of the lift cylinder. Hook
the free end of the spring (Item 1) B to the
lift arm support device so there will be no
interference with the support device
engagement. With the operator in the seat, seat
belt fastened and seat bar lowered, start the
engine. Raise the lift arms, until the lift arm
support device drops onto the lift cylinder rod
C. Lower the lift arms slowly until the
support device is held between the lift arm and
the lift cylinder. Stop the engine. Raise the
seat bar and move foot pedals (or hand controls)
until both lock. Install pin (Item 1) C into
the rear of the lift arm support device below
the cylinder rod.
C
1 1 1
P03922
Service lift arm support device if damaged
or if parts are missing. Using a damaged lift
arm support or with missing parts can cause lift
arms to drop causing injury or death. W22711197
763/763H BICS Loader Service Manual
17
Revised Jan. 02
19
LIFT ARM SUPPORT DEVICE (Contd) Disengaging The
Lift Arm Support Device Remove the pin from the
lift arm support device. Connect the spring
(Item 1) A from the lift arm support device to
the bracket below the lift arms. With the
operator in the seat, seat belt fastened and seat
bar lowered, start the engine. Raise the lift
arms a small amount and the spring will lift the
support device off the lift cylinder rod. Lower
the lift arms and stop the engine. Raise the seat
bar and move pedals (or hand controls) until
both lock. Disconnect the spring from the
bracket. Raise the support device into storage
position and insert pin (Item 1) B through
lift arm support device and bracket. Connect
spring to pin.
A
1 1 1
P03921
B
1 1 1
P03923
763/763H BICS Loader Service Manual
18
Revised Jan. 02
20
OPERATOR CAB Description The Bobcat loader has
an operator cab (ROPS and FOPS) as standard
equipment to protect the operator from rollover
and falling objects. Check with your dealer if
the operator cab has been damaged. The seat belt
must be worn for roll over protection. ROPS/FOPS
Roll Over Protective Structure per SAE J104 and
ISO 3471, and Falling Object Protective
Structure per SAE J1043 and ISO 3449, Level l.
Level ll is available. Level l Protection
from falling bricks, small concrete blocks and
hand tools encountered in operations such as
highway maintenance, landscaping, and other
construction site services. Level ll
Protection from falling trees, rocks for
machines involved in site clearing, overhead
demolition or forestry. Emergency Exit The
front opening on the operator cab and rear window
provide exits. Rear Window Pull on the tag on
the top of the rear window to remove the rubber
cord A. Push the rear window out of the rear of
the operator cab. Exit through the rear of the
operator cab B. NOTE When an Operator Cab
Enclosure Kit is installed, the window of the
front door can be used as an emergency exit.
C Pull the plastic loop at the top of the
window in the front door to remove the rubber
cord C.
A

P00660
B

P00074
C

P09216
Push the window out with your foot D. Exit
through the front door.
D

P09217
763/763H BICS Loader Service Manual
19
Revised Jan. 02
21
OPERATOR CAB (Contd) Raising The Operator Cab
Never modify operator cab by welding, grinding,
drilling holes or adding attachments unless
instructed to do so by Bobcat Company. Changes
to the cab can cause loss of operator protection
from rollover and falling objects,
and result in injury or death.
W20691299
AVOID INJURY OR DEATH When operator cab is
equipped with a cab enclosure kit (front door,
side windows and top window) and other
accessories, the cab will not stay in the fully
raised position. Use a chain hoist to secure cab
in fully raised position or lower cab until it
rests against the cab latch on
Stop the loader on a level surface. Lower the
lift arms. Stop the engine. If the lift arms
must be up while raising the operator cab,
install an approved lift arm support device.
(See Page 17.)
the gas spring.
W21560594
Never work on a machine with the lift arms up
unless the lift arms are secured by an approved
lift arm support device. Failure to use an
approved lift arm support device can allow the
lift arms or attachment to fall and cause injury
or death. W20590598
Use care when raising or lowering the operator
cab to prevent damaging the shaft of the lift arm
bypass control.
I20700596
If equipped with with mechanical hand
controls Disconnect the control linkage joint
from the bottom hole (work position) and move to
the TOP hole on the control handle (both sides)
A. Both control handles must be in the
vertical position so there will be no cab
interference with the steering levers when the
operator cab is raised or lowered.
A

P03470
Before the cab or the lift arms are raised for
service, jackstands must be put under the rear
corners of the frame. Failure to use jackstands
can allow the machine to tip backward causing
injury or death. W20140895 AVOID INJURY OR
DEATH Accidental movement of the loader, the lift
arms or the attachment can occur if the lift or
tilt control handles are not positioned
correctly before lifting or lowering the
cab. Move control linkage to top hole in handles
as shown, so cab does not hit handles when being
lifted or lowered. W21570594 Loosen and
remove the nut and plate (both sides) from the
front corner of the operator cab B.
B

P01518 P01528
763/763H BICS Loader Service Manual
110
Revised Jan. 02
22
OPERATOR CAB (Contd) Raising The Operator Cab
(Contd) Lift on the grab handle and bottom of
the operator cab slowly until the cab latching
mechanism engages and the cab is all the way up
A.
A

P03806
Lowering The Operator Cab NOTE Make sure the
seat bar is fully raised or lowered when
lowering the cab. Use the grab handles to lower
the cab. Pull down on the bottom of the operator
cab until it stops at the latching mechanism.
Release the latching mechanism and pull the cab
all the way down B.
B

P01565
Install the plate and nut (both sides)
C. Tighten the nuts to 4050 ft.lbs. (5468
Nm) torque.
C

P01518
If equipped with mechanical hand controls Move
the control linkage from the top hole to the
BOTTOM hole (work position) on the control
handle (both sides) D.
D

P03561
763/763H BICS Loader Service Manual
111
Revised Jan. 02
23
SEAT BAR RESTRAINT SYSTEM (Foot
Pedals) Description The seat bar restraint system
has a pivoting, spring assist seat bar with arm
rests and has spring loaded interlocks for the
lift and tilt functions. The operator controls
the use of the seat bar. The seat bar in the
down position helps to keep the operator in the
seat. The interlocks require the operator to
lower the seat bar in order to operate the foot
pedal controls. When the seat bar is up, the lift
and tilt control functions are locked when
returned to the NEUTRAL POSITION.
A
Clean (Both Sides)
P10361
Seat Bar Inspection Sit in the seat and fasten
the seat belt. Engage the parking brake. Pull
the seat bar all the way down. Start the engine.
Loaders without seat sensors press the green
PRESS TO OPERATE Button. Operate each foot pedal
to check both the lift and tilt functions. Raise
the lift arms until the bucket is about 2 feet
(600 mm) off the ground. Raise the seat bar. Try
to move each foot pedal. Pedals must be firmly
locked in neutral position. There must be no
motion of the lift arms or tilt (bucket) when the
pedals are pushed. Pull the seat bar down.
Loaders without seat sensors press the green
PRESS TO OPERATE Button. Lower the lift arms.
Operate the lift pedal. While the lift arms are
going up, raise the seat bar and the lift arms
should stop. Lower the seat bar. Loaders without
seat sensors press the green PRESS TO OPERATE
Button. Lower the lift arms and put the bucket
flat on the ground. Stop the engine. Raise the
seat bar and operate the foot pedals to be sure
that the pedals are firmly locked in the neutral
position. Unbuckle the seat belt. Seat Bar
Maintenance See the SERVICE SCHEDULE Page 13 and
on the loader for correct service
interval. Clean any debris or dirt from the
moving parts A B. Inspect the linkage
bolts and nuts for tightness. The correct torque
is 2528 ft.lbs. (3438 Nm). If the seat bar
system does not function correctly, check for
free movement of each linkage part. Check for
excessive wear. Adjust pedal control linkage.
Replace parts that are worn or damaged. Use only
genuine Bobcat replacement parts.
AVOID INJURY OR DEATH Never operate loader
without pedal lock shield 6705474 on both
interlocks. Shields prevent foot from unlocking
interlocks when leaving loader seat. W21621194
B
Interlock
Shield
Clean (Both Sides)
P01640
AVOID INJURY OR DEATH The Seat Bar System must
lock the lift and tilt foot pedals or hand
controls in neutral when the Seat Bar is up.
Service the system if controls do not lock
correctly. W22630597
763/763H BICS Loader Service Manual
112
Revised Jan. 99
24
SEAT BAR RESTRAINT SYSTEM (Mechanical Hand
Controls) Description The seat bar restraint
system has a pivoting, spring assist seat bar
with arm rests and has spring loaded interlocks
for the lift and tilt control functions. The
operator controls the use of the seat bar. The
seat bar in the down position helps to keep the
operator in the seat. The interlocks require the
operator to lower the seat bar in order to
operate the hand controls. When the seat bar is
up, the lift and tilt control functions are
locked when returned to the NEUTRAL POSITION.
A
Clean
(Both Sides)
2.
P10361
Seat Bar Inspection Sit in the seat and fasten
the seat belt. Engage the parking brake. Pull
the seat bar all the way down. Loaders without
seat sensors press the green PRESS TO OPERATE
Button. Start the engine. Operate each hand
control to check both the lift and tilt
functions. Raise the lift arms until the bucket
is about 2 feet (600 mm) off the ground. Raise
the seat bar. Try to move each hand control. The
controls must be firmly locked in neutral
position. There must be no motion of the lift
arms or tilt (bucket) when the controls are
moved. Pull the seat bar down. Loaders without
seat sensors press the green PRESS TO OPERATE
Button. Lower the lift arms. Operate the lift
control. While the lift arms are going up, raise
the seat bar and the lift arms should
stop. Lower the seat bar. Lower the lift arms.
Loaders without seat sensors press the green
PRESS TO OPERATE Button and put the bucket flat
on the ground. Stop the engine. Raise the seat
bar and operate the hand controls to be sure
that the controls are firmly locked in the
neutral position. Unbuckle the seat belt. Seat
Bar Maintenance See the SERVICE SCHEDULE Page 13
for correct service interval. Clean any debris
or dirt from the moving parts A B. Inspect
the linkage bolts and nuts for tightness. The
correct torque is 2528 ft.lbs. (3438 Nm). If
the seat bar system does not function correctly,
check for free movement of each linkage part.
Check for excessive wear. Adjust hand control
linkage. Replace parts that are worn or damaged.
Use only genuine Bobcat replacement parts.
AVOID INJURY OR DEATH Never operate loader
without interlock shield 6705474 on both
interlocks. Shields prevent foot from unlocking
interlocks when leaving
loader seat.
W21580594
B
Interlock
Shield
Clean (Both Sides)
P01640
AVOID INJURY OR DEATH The Seat Bar System must
lock the lift and tilt foot pedals or hand
controls in neutral when the Seat Bar is up.
Service the system if controls do not lock
correctly. W22630597
763/763H BICS Loader Service Manual
113
Revised Jan. 99
25
SEAT BAR RESTRAINT SYSTEM (Advanced
Hand Controls) Description The seat bar restraint
system has a pivoting seat bar (Item 1) A with
arm rests. The operator controls the use of the
seat bar. The seat bar in the down position
helps to keep the operator in the seat. When
the seat bar is down and the green PRESS TO
OPERATE Button is activated, the lift, tilt, and
traction drive functions can be operated. When
the seat bar is up, the lift, tilt, and traction
drive functions are deactivated. Seat Bar
Inspection Sit in the operators seat. Turn the
key ON, lower the seat bar and press the green
PRESS TO OPERATE Button. Both lights on the left
handle should be ON. Move each hand control back
and forth. You should hear the zipzip sound of
the lift and tilt actuators moving the control
valve spools (under the seat). Raise the seat bar
fully. Both lights on the left handle should be
OFF. Move each hand control back and forth. There
must be no zipzip sound of the lift or tilt
actuators. If either actuator makes a sound
while the seat bar is raised, contact your
dealer for service. Seat Bar Maintenance See the
SERVICE SCHEDULE Page 13 for correct service
interval. Clean any debris or dirt from the
moving parts B. If the seat bar system does
not function correctly replace parts that are
worn or damaged. Use only genuine Bobcat
replacement parts.
A
1 1 1
P13721
B
Clean
(Both Sides)
P10361

• Before you leave the operators seat
• Lower the lift arms, put the attachment flat on

the ground.

• Stop the engine.
• Engage the parking brake.
• (Advanced Hand Controls) Move the hand controls
  to the NEUTRAL POSITION to make sure that both
  lift and tilt functions are deactivated.
• The seat bar system must deactivate the lift and
  tilt control functions when the seat bar is
• up. Service the system if hand controls do not
  deactivate.
• W23210698

• Raise seat bar.

763/763H BICS Loader Service Manual
Revised Jan. 99
114
26
AIR CLEANER SERVICE Replacing Filter Element WITH
CONDITION INDICATOR (Without BOSS?) Replace the
large (outer) filter element only when the red
ring shows in the window of the condition
indicator (Item 1) A. NOTE Before replacing
the filter element, push the button on the
condition indicator (Item 2) A. Start the
engine. If the red ring does not show, do not
replace the filter element.
A
1
2
P10308
WITH BOSS? OPTION It is important to change the
air filter element only when the service codes
(on the BOSS? option instrument panel) shows the
symbols AF.2 B.
B
MC02320
Open the rear door. Remove the dust cover wing
nut (Item 1) C. Remove the dust cover (Item 2)
C.
C
2 1 2 1 2 1
P10313
Remove the wing nut (Item 1) D from the large
air filter element.
D
1 1 1
P10314
763/763H BICS Loader Service Manual
115
Revised Jan. 02
27

• AIR CLEANER SERVICE (Contd)
• Replacing Filter Element (Contd)
• Remove the large filter element A.
• NOTE Be sure all sealing surfaces are free of
  dirt and debris.
• Install the new filter element and washer and
  tighten the wing nut.
• NOTE Be sure sealing washer(s) is installed in
  its original location.
• Install the dust cover, washer and tighten the
  wing nut.
• Check the air intake hose for damage. Check the
  air cleaner housing for damage. Check to make
  sure all connections are tight.
• Only replace the inner filter element under the
  following conditions
• Replace the inner filter element every third time
  the outer filter is replaced.
• Press the button to remove the red ring in the
  condition indicator after the outer element has
  been replaced. Start the engine and run at full
  RPM. If the red ring shows again, replace the
  inner filter element.
• BOSS? Only If the service codes show symbols
  AF.2 during full engine speed, replace the inner
  filter element only after the outer filter
  element has been changed.
• Remove the outer element. (See Page 11.) Remove
  the inner filter wing nut (Item 1) B. Remove
  the inner filter element C.
• Install a new filter and tighten the wing nut.
  Close the rear door before operating the loader.

A

P10312
B
1 1 1
P10310
C

P10309
763/763H BICS Loader Service Manual
116
Revised Jan. 02
28
Suggest If the above button click is invalid.
Please download this document first, and then
click the above link to download the complete
manual. Thank you so much for reading
29
FUEL SYSTEM Fuel Specifications Use only clean,
high quality diesel fuel, Grade No. 2 or Grade
No. 1. The following is one suggested blending
guideline which should prevent fuel gelling
problems at cold temperatures Temp. F? (C?) No.
2 No.1
A
1 1 1
P03935
15? (9?) Down to 20? (29?) Below 20? (29?)
100 50 0
0 50 100
Contact your fuel supplier for local
recommendations. Filling The Fuel Tank
B WRONG WRONG

B13456
Stop and cool the engine before adding fuel. NO
SMOKING! Failure to obey warnings can cause an
explosion or fire. W20630887
Remove the fuel fill cap (Item 1) A. Use a
clean, approved safety container to add fuel of
the correct specifications. Add fuel only in an
area t