1986-1989 Honda TRX 250R Fourtrax Service Repair Manual Instant Download

1
(No Transcript)
2
HOW TO VSE NIS NAXAL Sections 1 and 2 apply
to the whole FOURTRAX, while sections 3
through 15 describe parts of the FOURTRAX,
grouped ac- cording to location.
INTENTS
GENERAL INFORMATION
MAINTENANCE
FUEL SYSTEM
ENGINE REMOVAL/INSTALLATION 4
CYLINDER HEAD/CYLlNDER/PISTON
ALTERNATOR
CLUTCH/BALANGER/GEARSHIFT LINKAGE/ KICK STARTER 7
TRANSMISSION/CRANXSHAFT 8

COOLING SYSTEM ia aii
FRONT WHEEL SUSPEN ON STEER N aii
aii
REAR WHEEL/DRIVE MECHANISM 11

REAR SUSPENSION 12
HYDRAULIC DISC BRAKES
FENDERS/EXHAUST SYSTEM 14
14
ELECTRICAL SYSTEM 15

TROUBLESHOOTING . 6

INDEX
Find the section you want on this page, then turn
to the table of contents on page 1 of that
section. Most sections start with an
assembly or system illustration, general
instructions, spec ifications, torque values,
tools and trouble shooting for the section.
The subsequent pages give detailed
procedures. If you don't know the source of a
problem, see section 16, TROUBLESHOOTING.
ENGINE
All information. Illustrations. directions and
speci- fications included in this publication are
based on the latest product information available
at the time of approval for printing. HONDA
MOTOft CO., LTD. reserves the right to make
changes at any time without notice and without
incurrinjg any obligation whatever. No part of
this publication mY be reproduc6d without
written permission. HONDA MOTOR CO.,
LTD. Service Publications Office
,
Date of issue September, 19B8 HONDA MOTOR CO.,
LTD.
3
1. GENERAL INFORUATION

1. TORQUE VALUES
2. TOOIS
3. CABLE HARNESS ROUTING
4. OPTIONAL PARTS LIST

1-5 1-7 1-9 1-'t5
GENERAL SAFETY SERVICE RULES MOOEL
IDENTIFICATION SPECIFICATIONS
GENERAL SAFEN
NJ the engine znuxt be running to do sozrie work,
matte sure the area is well-ventilated. Never my
the engine in a closed area.
Gasoline is extremely mmable and i esplOsive
under certain conditionc. Do not smoke or allow
flames or sparhs in your working area or where
gasoline is stored.
W ARNING,
CAUTION Used engine oil may cause skin cancer
f/repeored/J left fft on- fact with the skin for
prolonged periods. Although this is un- likely
unless you handle used oil on a daily basis, it
is still ad- viseable to thoroughly wash your
hands with soap and water as soon os possible
after handling used oil.
Inhaled mhbestos fibers have been found to o
respiratory disease and cnnrer. Never use an air
hose or ary brush to clean brake or clutch
assemblies. In the united stotes, Use an OSHA-
approved vacuum cder or otternate method approved
by OSHA designed to otieimicr rhe 6euird caused
by otrboma es- tastes fibers.

• SERVICE RULES
• Use genuine HONDA or HONDA-recommended parts and
  lubricants or their equivalent. Parts that do not
  meet HONDAs design specifications may damage
  the Fourtrax.
• Use the special tools designed for this product
  to avoid damage and incorrect assembly.
• Install new gaskets, O-rings, cotter pins, lock
  plates, etc. when reassembling.
• When torquing a series of bolts or nuts, begin
  with larger-diameter or inner bolts first, and
  tighten to the specified torque diagonally, in
  incremental steps, unless a particular sequence
  is specified.
• Clean parts in non-flammable or high flash point
  solvent upon disassembly. Lubricate any sliding
  surfaces before re-
• assembly.
• When installing a new oil seal, make sure that
  the sealing lip is lubricated with grease. If an
  oil seal and related parts have been washed,
  apply proper grease to the lip of the oil seal.
• After teassembly, check all parts for proper
  installation and operation.
• Use only metric tools when servicing this
  Fourtrax. Metric bolts, nuts, and screws are not
  interchangeable with English
• fasteners. The use of incorrect tools and
  fasteners may damage the Fourtrax.
• Route all electrical wires and control cables as
  shown on page \ -9 through 1-14 Cable and Harness
  Routing.

1-1
4
https//www.ebooklibonline.com Hello dear
friend! Thank you very much for reading. Enter
the link into your browser. The full manual is
available for immediate download. https//www.ebo
oklibonline.com
5
Gf!NERAL INFORMATION

MDDELlDiNTlFlCATlON '8E shown g7 similar
After '87
1 FRAM E SERIAL NUM BER
( 1 j FRAME SERIAL NU MBER
The frame serial number is stamped on the frame
front side.
the frame serial number is Stamped on the frame
ieft side.
f3) CARBURETOR IDENTIFICATION NU MBER
f2) ENGINE SERIAL NUM BER
The enpine serial number is stamped on the
crankcase lower left side.
The carbu\ etor \dent\t\cation number \s stamped
on the carburetor body right sid e .
1-2
6
GENERAL INFORMATION
SPEIFlkTI0XS
DIMENSIONS Overall length "86, 87 ARer 87 , Overall width 86, 87 Aher B7 Overall height 86, 87 AHar 87 Wheelbase 86, 87 AMer '87 Seat height 86.'87 ARe'87 Foot peg height '86. 87 AMa87 Ground clearance Dry weight Front 86. 87 Aher 'f7 Rear Weight distribution Front 86, 87 After 87 Rear '86. 87 After "87 1,B25 mm (71.9 in) 1,840 mm (72.4 in) 1, t3O mm (44.5 in) 1,160 mm (45.7 in) 1,070 mm f42.1 if3) 1,080 mm (42.5 in) 1,295 mm 151.0 in) t ,285 mm (49.8 in) 775 mm (30.5 in) 790 mm (31.1 in) 330 mm I13.0 in) 340 mm (t3.4 in) 110 mm (4.3 in) 75 kg (165.3 Ibl 73 kg (160.9 tb) 74 kg 1163. t Ib) 106 kg 1233.7 lb) 101 kg (222.7 lbl 131 kg (288.B Ib) 133 kg (293.2 Ibl .
FRAME Type Front suspension, travel Rear suspension. travel Rim size Front Rear Tire size Front 86, B7 Aher B7 Rear 88, 87 After 87 Tire pressure Front Rear 86, 87 Aher B7 Front brake, lining swept area year bfake, lininp swept area Fuel capacity Fuel reserve capacity Toe-in Caster angle 86. 87 After 87 Camber Trail lentjth 86, 87 Aher 87 Tread Front Rear "86, 87 Cradle Double wish-bone, 200 mm \7.9 in) Swifigarm. Pro-link, 230 mm (9.1 in) t 0 x 5.5 9 x 8.0 AT 27 x 7. 10 AT22 x 7.OO-lOña 2O x 1O.OO-9 AT2O X 1O.009 4.O psi 10.275 kg/cm. 27.5 kPa) 2.9 psi (O.2 kg/cm2, 2O kPa) 3.3 psi (0.225 kg/cm, 22.5 kPa) Single disC ltwin piston), 392.9 cm2 (80.9 sq-in) x 2 Single disc (twin pfiaton), 2fi'8.8 cm' I40.3 sq-in) 1O.O I 12.64 U.S. gal., 2.20 Imp. gal.) 2.O f (O.53 U.S. gaL, 0.44 Imp. gel-) IO mm 10.4 in) 6 44O O 27 mm ft .OB inl 21 mm (0.83 in) 910 mm 135.8 in) 870 mm (34.3 in) 900 mm f35.4 in) Cradle Double wish-bone, 200 mm \7.9 in) Swifigarm. Pro-link, 230 mm (9.1 in) t 0 x 5.5 9 x 8.0 AT 27 x 7. 10 AT22 x 7.OO-lOña 2O x 1O.OO-9 AT2O X 1O.009 4.O psi 10.275 kg/cm. 27.5 kPa) 2.9 psi (O.2 kg/cm2, 2O kPa) 3.3 psi (0.225 kg/cm, 22.5 kPa) Single disC ltwin piston), 392.9 cm2 (80.9 sq-in) x 2 Single disc (twin pfiaton), 2fi'8.8 cm' I40.3 sq-in) 1O.O I 12.64 U.S. gal., 2.20 Imp. gal.) 2.O f (O.53 U.S. gaL, 0.44 Imp. gel-) IO mm 10.4 in) 6 44O O 27 mm ft .OB inl 21 mm (0.83 in) 910 mm 135.8 in) 870 mm (34.3 in) 900 mm f35.4 in)
ENGINE Type Cylinder arrangement Engine dry weight Bore x stroke Displacement Compression ratio 86 Aher 86 Transmission oil capacity Lubrication system Fuel required Air filtration Idle speed Liquid cooled 2-stroke 7 inclined from vertical, single 26.0 kg (57.3lbl 66.0 x 72.0 mm (2.00 x 2.83 in) 246 cm (15.01 cu-in) 7.5 1 7.7 1 O.7 I 10.74 U.S. qt., 0.62 Imp. qt.) at disassembly O.6 I IO.83 U.S. qt., O.53 Imp. qt.) aher draining Gasoline/oil mixture Gasoline-oil ratio 20 1 (pre-mixedl (RON, 92-fO0I Oilad polyurethane foam 1,500 150 rpm Liquid cooled 2-stroke 7 inclined from vertical, single 26.0 kg (57.3lbl 66.0 x 72.0 mm (2.00 x 2.83 in) 246 cm (15.01 cu-in) 7.5 1 7.7 1 O.7 I 10.74 U.S. qt., 0.62 Imp. qt.) at disassembly O.6 I IO.83 U.S. qt., O.53 Imp. qt.) aher draining Gasoline/oil mixture Gasoline-oil ratio 20 1 (pre-mixedl (RON, 92-fO0I Oilad polyurethane foam 1,500 150 rpm
1-3
7
GEfJERAL INFORMATION
CARBU RETOR Type Ictentification number '86 '87 '88 After 88 Main Jet 86 87 88 After g8 Venturi diameter Slow jet ' 8 6, 87 ! 88 A tter '88 Float level Air screw initial opening 86, 87 88 After 88 Jet needle 86, After 88 87, 88 Piston valve PJ ORA PJ 07A PJS7B PJ07C 150 1 52 1 58 15 5 34 mm 11. 3 in) 4B 45 42 16 mm (0. 62 in) 1-7 8 turns out 1 -3,/4 turns out 1 -1,/2 turns out 4th groove 3rd groove
ORIVE TRAI N Clutch Transmission rirnayreductionratio Gear raiios l II il I IV 'B6 After 86 86 After 86 Final reduction ratio 86, 87 After 87 Ge arshift p8ttern Wet multi- plate type 6-speed , constant mesh 2.652 I61.'23) 2. 570 \3b I 4\ 2.062 (33..' 16) 1.667 (30,18 1.333 (28,21 1.083 (26,.'24) 1 .087 (2 5/ 23) 0.884 (23..'26 0. 920 i23.25 3.000 39,13) 2.923 I3B.13) Left foot operated return system , 1-N-2-3-4- 5-6
E..E CTRICAL Ignition system Ignition timing "F" mark 86, '87 After 87. Starting system Abe nator 86-' 88 After 88 Spark plug 86, After 88 ISTD) 87, '8B fSTDI Spark plug Tailight 86 After 86. He adlight CDI 1 9 BT DC,'1, 500a 1 50 rpm 21 " BTDC.'1,500z150 rpm Primary kick starter 0. 159 kW 5,000 rpm 0. 1 54 kW/5,000 rpm BR8ES fNGK) R N3C (CHAMPION) BR9ES (NG K) RN 2C (CHA MPION) 0.7 0. 8 mm 0.028 0.031 in) 12 V 8 W 2 V 5 W 12 V 55. 60 W
1-4
8
GENERALINFORMATION
_at_RUE VALUES ENGINE
ITEM I- I THREAD DIA. (mm) TORQUE Nm (kg-m. ft-lb) REMARKS
Cylinder head nut 6 8 2429 (2.42.9, 1721) 2429 (2.42.9, 1721)
Cylinder base nut 4 10 38-48 13.8-4.8, 27351 38-48 13.8-4.8, 27351
Clutch center lock nut 1 18 s5 is is.56.5. 4047) s5 is is.56.5. 4047)
Primary drive gear bolt 1 10 4050 (4.O5.O, 29 36) 4050 (4.O5.O, 29 36)
Shih drum center pin 1 8 2024 (2.O2.4, 14 17) 2024 (2.O2.4, 14 17)
Transmission drain bolt 1 12 25-35 (2.5-3.5, 18 -251 25-35 (2.5-3.5, 18 -251
Countershaft bearing holder screw 2 6 8-12 (O.81.2, 6-9) 8-12 (O.81.2, 6-9)
Shift drum stopper arm bolt 1 6 I 0-14 (1.O1.4, 710) I 0-14 (1.O1.4, 710)
Alternator rotor nut j 12 6575 (6. 57.5, 4754) 6575 (6. 57.5, 4754)
Drive sprocket bolt 1 8 3034 (3.O3.4, 2224 3034 (3.O3.4, 2224
Water pump impeller nut BB88 1 6 812 10.8 I .2, 6-91 812 10.8 I .2, 6-91
Water pump impaller After 88 1 0 1014 (1.O1.4. 7 TO) 1014 (1.O1.4. 7 TO)
Spark plug 1 14 5-20 (1.5-2.0, 1 J t4l 5-20 (1.5-2.0, 1 J t4l
Coolant drain boh 2 6 812 (O.8 I .2, 69) 812 (O.8 I .2, 69)
CHASSIS
ITEM OTY THREAD DIA. cmml TORQUE Nm (kg-m, ft-lb) TORQUE Nm (kg-m, ft-lb) REMARKS
Gearshift pedal bolt 1 6 10-14 f1.01.4, 710)
Kick starter pedal pinch bolt 1 8 2035 (2.O3.5, 1425)
Parkine brake adjust bolt lock nut 1 B 15-20 (1.5-2.0, 111 4)
Front wheel hub nut 86, "87 2 18 801 2O (8.O 1 2.0. 5872)
Aher 87 2 14 BOBO 6.O8.O, 4358
Tie-rod ball joint nut 4 10 4050 I4.O5.0, 29361
Tie-rod lock nut 4 12 50-60 i5.O-6.o. 3s4a)
Front arm bell joint nut (86, 87 onlyI 2 14 608O in.oa.O. 4s 58)
Knuckle arm nut (86, 87 only) 4 10 6070 in.o7.O, 4s 51)
Front arm nut 4 12 5060 15.O - 6.0, 3B 43)
Front arm mounting bolt
86. ARer 87 8 10 3545 (3.54.5, 25 331
87 g 10 5060 (5.O6.O, 36431
Front shock absorber mounting bolt 4 10 4050 f4.0-5.0, 29361
Steering shah nut 1 14 6080 \6.0-8.0. 4358)
Handlebar lower holder mounting
nut 2 10 405O (4.O5.0, 2936)
Steering shaft holdar bolt 4 8 2530 I2.53.O, 122)
Rear axle outer lock nut 1 48 80100 18.0 JO.O, 58-72) left hend threads
Rear axle inner lock nut 1 48 120 t4O (12.O 14.0. 87 101I left hand threads
Rear wheel hub nut 2 20 120170 (1 2.O17.0, 87 123) apply oil or grease to
Front, rear wheel nut 16 10 60-70 f6.0- 7.O, 43 51) tapered nut
Handlebar upper holder bolt 4 8 24-30 (2.43.0, 1722)
1-5
9
GENERAL INFORMATION
ITEM T THREAD DIA. cmml TORQUE Nm (kg-m. ft-lb) REMARKS
Front disc socket bolt 8(6) 6 1416 (1.4 1.6, 10 12)
Front brake caliper mounting bolt 4 8 2030 12.O3.0, 1422)
Brake hose oil bolt 5 JO 25-35 (2.53. 5, 18 25)
Bleed valve 3 7 4-7 IO.4 O.7, 3 SI
Year disc socket bolt 4 8 354O 13.5-4.0, 25-291
Pad pin bolt 4 8 15-20 11.5-2.0, 1014)
Pad pin bolt plug 4 8 1020 (1.O2.O, 71 4)
Pear caliper bracket mounting bolt 2 8 2834 I2.B3.4, 20251
Rear caliper mounting bolt 1 8 2O25 (2.O-2.5. 14-18
Front brake pipe nut 2 10 1520 (1.52.O, 11 141
Brake hose joint
(hose side) (86, 87 only) 2 10 1215 (1.2 I .5, 9 1 I )
(joint side) (88, 87 only) 2 10 3040 (3.O4.O, 2229)
Three-way joint mounting bolt 2 (1) is o1s 1.O 1.4, 7 10 ft-lb)
Front master cylinder holder 2 6 10 t4 (1.O I .4, 710 fi-lb)
Master cylinder cover screw 4 4 12 (0.1 O.2, O.7 1.4)
Parking brake attaching bolt 2 8 2025 2.O 2.5, 14 18)
Shock absorber hose oil bolt C.ompression damping valve Rear shock absorber mounting bolt 2 1 IO 2832 f2.83.2, 2023l 15-20 f1. 5-2.0, I 114)
(upper) 1 1O 45- 55 (4. .5, 33-401
(lower) 1 12 7O BO (7.O_at_.O, 5158)
Shock arm pivot bolt 1 12 70-80 17.0-8.0, 5J 58)
Shock link pivot bolt 1 12 70-80 (7.0-8.0, 51 581
Swingarm pivot nut 1 14 70 1 10 (7.O I 1.O, 5 80)
fiiwingarm bearing holder socket bolt 2 14) 8 19 23 (1.92.3. 1417) Apply oil or
grease to
threads
Driven sprocket bolt 10 47-55 14.7 - S. 5, 34-4O) Apply locking
agent to
threads
Engine hanger plate and pipe bolt 8 25 35 (2.53.5, 18-25)
Engine mounting bolt Foot peg mounting bolt 5 (4) 10 5O BO (5.O Is.O, 3643)
(86, B7 only) Shock absorber spring lock nut 4 1 10 50-60 15.O6.O, 36 43) 80-100 (8.O-00.0, 58-72
Skid plate 4 8 283 f2.8-3.4, 20-25)
Radiator hose band 6 O.7-1.O (O.O7-O., 0.5-0.7)
Rear brake torque bolt (Aher 87-) 1 12 5060 s.o Is.o, a643) Apply locking
agent
Torque specifications listed above are for
important fasteners. Others should be tightened
to standard torque values listsd below. STANDARD
TORQUE VALUES
ITEM TORCtUE Nm (kg-m, ftlbl ITEM TOROUE Nm (kg-m, ft-lb)
3 mm bolt and nut 4.56 (O.45O.6, 3-4) 5 mm screw 3.55 (O.35 O.5, 24)
d mm boit and nut 8 12 10.8 1.2, 69) 6 mm screw and 6mm bolt 7 1 1 (O.7 1.1, 58)
with 8 mm head
9 mm bait and nut 1825 (1.82.5, 131 B) 6 mm flange bolt and nut 1014 (1.O1.4, 710)
10 mm bolt and nut 30-40 f3.0-4.0, 2229I B mm flange bolt and nut 2430 (2.43.O, 1722)
12 mm bolt and nut 506O (5.O6.O. 36-431 10 mm flange bolt and nut 3545 f3.54.5, 2533)
1-6
10
Suggest For more complete manuals. Please go to
the home page. https//www.ebooklibonline.com If
the above button click is invalid. Please
download this document first, and then click the
above link to download the complete manual. Thank
you so much for reading
11
GENERAL INFORMATION
TOOLS SPECIAL
DESCRIPTION TOOL NUMBER ALTERNATE TOOL TOOL NUMBER REF. SECT.
Camber/caster gauge attachment 07910 MJ3O100 Not available in U.S.A. 3
Crankcase puller 07973 -4300000 8
Bearing remover, I 7mm 07936 -3710300 6, 8
Remover handle 07936 -3710100 6, 8
Remover weight 077410010201 Remover weight 07936- 37 \ 0200 6, 8
Assemb Y bolt 079651660200 8
Thread adapter 07965 KA3O0O0 8
Driveshaft dis/assembly tool (B) 07964 MB002O0 8
Mechanical seal driver attachment 07945 -4150400 Mechanical seal installer GH AH 065 41 5 9
(U.S.A. only I
Attachment, 28 x 30 mm 0794618701O0 9
1 Z (After 87I
Bearing remover set, 1 2 mm 07936-1660001 Not available in U.S.A. 9
Remover weight 07741 OO1O2O1 Remover weight 07936 Z710200 9
Bearing spindle assy, 12 mm 07936-1660100 9
Universal bead breaker GN AH 958 BB1 (U.S.A only) 10
Ball joint remover gy941 692OOO3 10
Show k absorber compressor 07959 MB10000 10
attachment
Shock absorber compressor 07967 KC10100 Not available in U.S.A. IO
attachment
Lock nut wrench, 56mm 07916 HA2O0O0 Lock nut wrench, 56 mm 07916 HA201OA 11
(U.S.A. onlYt
Lock nut wrench, 45 mm 07916187O1O1 Equivalent commercially 11
available În U.S.A.
Valve wrench 07920 KA3O001 Not availabTe in U.S.A. 12
Needle bearing remover 07946 KASOOOO 12
Snap ring pliers 07914-3230001 13
Circuit tester (SANWA) 07308 OO200OO Circuit tester (KOWA) TH 5H 15
Digital multimater 074110O200OO Digital multimeter KS AHM 32-002 15
Spherical bearing driver 07HMF HCO01 00 (U.S.A. on\Yi 10
Bearing remover (Aher 87) 07931 MA70OO0 T 2
1-7
12
GEhlERAL INFORMATION COfJMON
DESC RIPTION TOO L NU MBER ALTER NATE TOOL TOOL NUMBER REF. SECT.
Flowt level gauge 0740 1 00 1 0000 Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly
Rot or puII er 07 733 001 OOOO Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly 079330O10O00 6
IJ ni /ersaI holder 07 72 5 OO 30OOO Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly 6
Clu'ch center holde 07 7 24 OOSOOO 1 Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly 7
Gec r holder 07 7 24 OO 101 OO Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly 7
Dr. er 07 749 OO 1 0000 Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly 6,8,9,10,11 , 12
AttJchment, 3 7 x 40 mm 07 746 OO 1 O200 Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly 6, 8, 1 0
Pilo t , 17 mm 07 746 0040400 Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly 6,10
Attchme t, 6 2 x 68 mm 07 746 OO 10500 Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly 8,11
Pilo r, 28 mm 07 746 004 1 100 Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly
Att.Jchment, 5 2 x 5 5 mm 077460010400 Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly
Pilot, 25 rnm 077460040600 Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly
Pilot, 2 2 mm 07746OO41O00 Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly 8
Pilot, 12 mm 07746OO40200 Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly 9
Ben ring remover shaft O7 746 00501 OO Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly 10
Bez ring i emo ver head , 20 mm OF 746 0050600 Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly 10
Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly 1 2 I After 871
Attachmen, 42 x 47 mm 07 746 0010300 Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly 1 0
Pict, 20 Ann 07746 0040500 Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly 1 0
Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly 1 2 fAfter 87a
Ben ring remover shaft 07 GGD 0010100 Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly 1 2
(After 87 Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly
Tir' bead breaker set 077s 2 OOSOOO 1- Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly 1 0
E reaker arm 0777 2 - OO5O200 Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly
E reaker arm compressor 07 7 72 0050 101 Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly
Shck absorber compressor 07 959 3290001 Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly 07G ME 001 OOOO 1 0
Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly 07GME 00101 00 10
Pilet, 40 mm 07746 0040900 Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly 11
Attachment, 32 x 3 5 mm 07746 00101 OO Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly 10
fAfter '8 7 Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly
lATter 87l 077460040200 Rotor puller Equivalent commercially av ailable in U.S.A . Not available in U. S . A. - Equiv alent commercially av a\IabIe in U. S.A . Not available in U. S A . Shock absorber compres- SOC -Compressor screw assebly 1 0
of-rionAL TOOLS
DES CRIPTION TOO L NUMBER ALTERNATETOOL TOOL NUMBER REF. SECT.
Pin spanner Pin spanner 892O1 KA4 8 1 0 892O2 KA4 8 1 0 1 2 1 Z
1-8
13
https//www.ebooklibonline.com Hello dear
friend! Thank you very much for reading. Enter
the link into your browser. The full manual is
available for immediate download. https//www.ebo
oklibonline.com