Pneumatic Road Tube Counters Version 3.0

1
Pneumatic Road Tube CountersVersion 3.0
(Press Esc to exit this presentation at
anytime.)
K-Hill Signal Company, Inc. Model KBA-II
2
K-Hill Signal Company, Inc.Model KBA-II, Time
Saver
3
KBA-II Key Features

• 8-place alpha/numeric liquid crystal display
  (LCD) with backlight option
• Magnet zero reset
• Magnet interval length selection
• Selectable intervals 1hr to 12 hrs., 1 day to
  99 days, and continuous
• Magnet interval data read out
• Grand total and 24 recorded intervals
• 5-year lithium batteries
• Simple to operate
• Waterproof / compact case
• 1/4" (6 mm) thick walled aluminum case, with
  lock and chain.

4
KBA-II Operation
The KBA-II Timesaver, traffic counter will count
in intervals of days, or hours (in increments
from 1 to 12 hours). You can log up to 24
intervals and the counter automatically stops
after the last interval, for later viewing. Each
logged interval will hold up to 9999 counts. The
KBA II, can display the current total, each
logged interval, and a real time update as
vehicles pass over the road tube.
5
KBA-II Operation
Note, disk magnets have been replaced with a wand.
Magnet
Display
Menu Side
Toggle Side
6
KBA-II Operation
Each swipe will sequentially display the
following screens
Swipe the M (menu) side with magnet
7
KBA-II Operation
Each swipe will sequentially display the
following screens
Swipe the M (menu) side with magnet
8
KBA-II Operation
Each swipe will sequentially display the
following screens
Swipe the T (toggle) side with magnet to select
options (shown here in blue).
9
Important Note
The counter is designed to tally one-half count
for each axle on the vehicle. Example, a two
axle truck towing a two axle trailer will show up
as a double count.
10
Important Note-contd
The counter will automatically shut off after
completing the 24 hours of counting.
11
KBA-II Installation Instructions
Recommended Tools Hammer
Step 1. Clear road surface of sharp debris that
may cut the rubber tube
Step 2. Secure plugged end of the road tube to
the road edge
Step 3. Secure counter end of the road tube to
the opposite road edge
Step 4. Reset (or zero) the counter and make a
note of the time (on the Traffic Counter Data
Collection Sheet).
12
KBA-II Calibration Initial Setup
As you swipe the Menu side, the following
sequence of information will be displayed. . .
Hint set this to 20 sec. It will allow more
time to view the display when extracting and
recording data.
13
KBA-II Calibration Initial Setup
14
KBA-II Calibration Initial Setup
This must be set to Yes by swiping with the
magnet on the T side of the counter, after you
have installed the counter at the sampling site.
Resetting the Counter
15
KBA-II Calibration Initial Setup
Total Counts
Log no00 corresponds to the first hour (or
interval period) of counts, Log no01 corresponds
to the second hour of counts, and so on.
Display
Number of counts for the 1 hour interval (Log
no00). This is the number you will be entering
into the summary sheet
16
KBA-II Recording Collected Data
The Done will be displayed when the 24 hours of
counts are completed.
Display
17
KBA-II Recording Collected Data
To advance the display of each Log noXX, you
must swipe the T (toggle) side of the counter
unit.
Display
18
KBA-II Recording Collected Data
Suggestions for using a form to record data
Use this column, (rounded off to closest half
hour) to indicate the time you started the
counter. This will determine what row (on this
form) to record your counts for each Log noXX.
19
KBA-II Recording Collected Data
Use this column to keep track of the interval Log
no00, Log no01, Log noXX.
Use this column to record counts for each
interval, Lxxxx.
20
KBA-II Product Service Information
K-Hill Signal Company, Inc. 326 West Third
Street Uhrichsville, OH 44683-2036 Contact Bill
Hall Phone [phone] or 740-922-0421 Fax
740-922-0421 Website www.khilltrafficounters.com
e-mail khillco_at_tusco.net
21
End of Demonstration
Return Home