VINYL PIPES

1
VINYL PIPES
FITTINGS
U-PVC HI-PVC
JIS SERIES
2
ASAHI AV VINYL PIPES U-PVC (HI-PVC)
VP and VM PIPES
VP and VM plane end pipe U-PVC JIS K 6741 or 6742
VP plane end pipe HI-PVC JIS K 6742
UNIT mm

• Notes
• The maximum outer diameter(minimum diameter) is
  the largest(smallest) of outer diameter
  measurement at a location.
• The average outer diameter is the average for
  outer diameter measurements made in a direction
  other than two parallel direction or a
  circumference measurement divided by 3.142.
• The mass per unit length(m) in the table, which
  was calculated using a specific gravity of
  U-PVC(1.43) is only for information, not part of
  standards.
• The length tolerance is 10mm or 10mm.
• The pipe of VM350 and VM400 are confirmed as JIS
  K 6741 standard.
• The pipe of HI-PVC is confirmed as JIS K6742
  standard.

3
ASAHI AV VINYL PIPES U-PVC
VU PIPES
VU Pipe - JIS K6741
VU Plane end pipe U-PVC
UNIT mm

• Notes
• The maximum outer diameter(minimum diameter) is
  the largest(smallest) of outer diameter
  measurement at a location.
• The average outer diameter is the average for
  outer diameter measurements made in a direction
  other than two parallel direction or a
  circumference measurement divided by 3.142.
• The mass per unit length(m) in the table, which
  was calculated using a specific gravity of
  U-PVC(1.43) is only for information, not part of
  standards.
• The length tolerance is 10mm, 10mm.

4
ASAHI AV TS FITTINGS
Common Dimension for TS Socket Connection
JIS K6743-1993
Nominal Size 13mm to 50mm
Nominal Size 65mm to 150mm
Taper 1/T
Taper 1/T
UNIT mm

• Notes
• Tolerance for dimension (l ) is 4mm, -0.5mm.
• Sizes marked with are according to AV original
  standard.

5
ASAHI AV TS FITTINGS
90º ELBOW
JIS K6743-1993
UNIT mm
Nominal Size 13mm to 50mm
Nominal Size 65mm to 150mm

• Notes
• Tolerance for dimension (H) is 4mm, -0.5mm.
• Sizes marked with are according to AV original
  standard.

SOCKET
JIS K6743-1993
UNIT mm
Nominal Size 13mm to 50mm
Nominal Size 65mm to 150mm

• Notes
• Tolerance for dimension (L) is 4.0mm, -4.0mm.
• Sizes marked with are according to AV original
  standard.

6
ASAHI AV TS FITTINGS
REDUCING SOCKET
Nominal Size 13mm to 50mm
JIS K6743-1993
Nominal Size 65mm to 150mm
UNIT mm

• Tolerance for dimension (L) is 4mm, -4mm.
• Sizes marked with are according to AV original
  standard.

Notes
7
ASAHI AV TS FITTINGS
UNIT mm
TEE
JIS K6743-1993
Nominal Size 13mm to 50mm
Nominal Size 65mm to 150mm

• Notes
• Tolerance for dimension (H) is 5mm, -1mm.
• Sizes marked with are according to AV original
  standard.

CAP
UNIT mm
JIS K6743-1993
Nominal Size 13mm to 50mm
Nominal Size 65mm to 150mm

• Tolerance for dimension (L) is 5mm, -0mm.
• Sizes marked with are according to AV original
  standard.
• Dimension of R is from 1mm to 5mm.

Notes
8
ASAHI AV TS FITTINGS
REDUCING TEE
JIS K6743-1993
Nominal Size 65mm to 150mm
Nominal Size 13mm to 50mm
UNIT mm

• Notes
• Tolerance for dimension (H and H1) is 5mm,
  -1mm.
• Sizes marked with are according to AV original
  standard.

9
ASAHI AV TS FITTINGS
FAUCET ELBOW
UNIT mm

• Notes
• Tolerance for dimension (H) is 5mm, -1mm.
• Tolerance for dimension (H1) is 5mm, -2mm
• Tolerance for dimension (l2) is 1mm, -1mm.

• Caution
• Use seal tape and gasket at thread connection.
• Do not use for connection between metal piping
  and U-PVC(HI-PVC) piping.
• Please set proper piping support around Elbow.

10
ASAHI AV TS FITTINGS
45º ELBOW
JIS K6743-1993
UNIT mm

• Notes
• Tolerance for dimension (H) is 5mm, -1mm.

11
ASAHI AV FITTINGS
AV 45º BEND
UNIT mm
AV 90º BEND
UNIT mm
12
ASAHI AV LARGE SIZE FITTINGS
AV SHORT ELBOW
UNIT mm
AV 90º BEND
UNIT mm
13
ASAHI AV LARGE SIZE FITTINGS
AV 45º BEND
UNIT mm
Maximum Permissible Working Pressure for AV Large
Size Fittings at ambient temperature
UNIT MPa
Maximum working pressure includes water hammer
pressure on hydrostatic pressure.
14
ASAHI AV LARGE SIZE FITTINGS
AV SOCKET (THICK WALL)
UNIT mm
AV REDUCING SOCKET
UNIT mm
15
ASAHI AV LARGE SIZE FITTINGS
AV TEE
UNIT mm
AV REDUCING TEE
UNIT mm