625 Series

1

• 625 Series
• Rapid Steamer Training

2
625-Series Rapid Steamer

• Specifications
• 220V, 50/60Hz, 15A
• Water Pressure 20-30 psi

3
625-Series Rapid Steamer

• Installation
• Remove steamer from box and position on shelf of
  toaster table.
• Attach water line to steamer regulator.
• Set water regulator to 25 psi.
• Plug in steamer.
• Turn on. Allow to warm up for 20 minutes.
• Cycle unit 3 times to purge air in water line.

4
625-Series Rapid Steamer
Celsius/Fahrenheit DOWN Arrow Button
Temperature UP Arrow Button
Prince Castle Logo Button
McDonalds Logo Button
Product Buttons (1 thru 4)
Start Button
Display
5
625-Series Rapid Steamer

• Operation
• Turn unit on, all segments on display will light
• Display will alternate between PRINCE
  CASTLE
• After 10 seconds, display reads PRE HEAT
• At operating temperature, display will change to
  product name assigned to button 1.

6
625-Series Rapid Steamer

• Operation
• To change display name from Product 1 to another,
  push the appropriate product button (
  or )
• Place product on spatula, cut side down.
• Press to begin a steam cycle.
• Tone will sound, display will count down cycle.
• When finished a tone will sound, display will
  flash

2
3
4
START
REMOVE
7
625-Series Rapid Steamer

• Programming
• Product button is preprogrammed for
• Product Buttons may be changed to
• PROD1 PROD12 may be changed to personalized
  product names.

FILET
1
8
625-Series Rapid Steamer

• Programming Assigning a Name to a Product Button
• Press and hold and the Product button for
  6 sec.
• Display will show currently assigned product for
  button.
• Press to scroll through names.
• Press to store change.

9
625-Series Rapid Steamer

• Programming Changing a Product Name
• Assign name to Product button.
• Press and hold for 6
  sec.
• Left-most character of name will begin to flash.
• Press to change character.
• Press or to move between characters.
• Press to store new name.

4
1
10
625-Series Rapid Steamer

• Programming Water Valve
• Once product name is stored, display will show
  water valve ON time.
• Press to adjust ON time.
• Press to store change. Display changes to
  valve OFF time.
• Press to adjust OFF time.
• Press to store change. Display changes to
  number of CYCLES.
• Press to adjust the number of CYCLES
• Press to save the changes.

11
625-Series Rapid Steamer

• Programming Set Point Temperature
• After saving water valve settings, display
  changes to set point temperature.
• Use to adjust the set point.
• Platen temperature can be set between
• 265-350 F or 129 176C

• Press to save changes to temperature

12
625-Series Rapid Steamer

• Programming Alarm Delay
• After saving the set point temperature, the
  display will show the Alarm Delay time setting.
• Press to adjust the Alarm Delay setting.
  
• The alarm delay may be set for 0 10 seconds.
• Press to save the change to the Alarm
  Delay and to exit the Program Mode.
• Note Pressing at any time exits the
  Program
• Mode without storing any changes.

3
13
625-Series Rapid Steamer

• Default Factory Presets
• Water Valve Factory Presets
• Water Valve ON 0.5 seconds
• Water Valve OFF 1.0 second
• Number of Cycles 6
• Alarm Delay 2.5 seconds
• Temperature Factory Presents
• 350F or 176C

14
625-Series Rapid Steamer

• Factory Presets Restoring Factory Presents
• Loading factory presents restores the unit to
  factory settings and voids all user programmed
  information.

• Turn unit off. Wait until display becomes blank
  and turn unit back on.
• During power up, press within 3
  seconds.
• Display will flash

4
1
PRESETS
LOADED
15
625-Series Rapid Steamer

• Temperature Calibration Changing from F to C
• Press and hold
• Display will show current temperatures setting.
• Press to change between F and C
• Release both and when finished.

16
625-Series Rapid Steamer

• Temperature Calibration Calibrating the Platen
• The CAL TEMP mode is used to calibrate the platen
  temperature with and external meter connected to
  the plug inlet on the right side of the unit.

Type K Thermocouple Connector
17
625-Series Rapid Steamer

• Temperature Calibration Calibrating the Platen
• Press and hold and for 6 seconds.
• Display will show current calibration temperature
• Press to zero the previous calibration
  offset.
• Display will now show current platen temperature
  without any calibration offset.
• Press to adjust temperature to
  calibration reading.
• Press to store calibration changes and
  exit CAL TEMP mode.

2
18
625-Series Rapid Steamer

• Manual Reset
• A hi-limit thermostat will turn off electrical
  power to the platen and control circuits if the
  unit overheats.

• Turn the unit off and let the unit cool down for
  10-25 minutes before resetting.
• Remove black cap at back of unit and press manual
  reset button to restart. Replace cap when
  complete.

Manual Reset
Rear of Unit
19
625-Series Rapid Steamer

• Cleaning Daily PM Tasks
• Wear protective gloves.
• Remove top cover, spatula, top cover and venturi
  plate.
• Wash top cover, top plate, and venturi plate in
  solution of McD APSC/APC.
• Rinse with clean water.
• Sanitize with solution of McD Sink Pak
  Sanitizer.

Top cover
Spatula
Venturi Plate
20
625-Series Rapid Steamer

• Cleaning Daily PM Tasks cont.
• Wipe steamer platen chamber with clean, sanitized
  cloth.
• Use a brush to clean the water tube.
• Dip the brush in deliming solution.
• Insert brush about 1 into water tube and remove.
• Repeat for 30 seconds.

Water Tube Inlet
Platen Chamber
21
625-Series Rapid Steamer

• Cleaning Daily PM Tasks cont.
• Use solution of McD APSC/APC in a spray bottle.
• Spray solution directly on clean, sanitized
  towel.
• Wipe all external surfaces with towel.
• Reassemble unit and run four steam cycles to
  remove residual cleaning solution and prime unit.
  

22
625-Series Rapid Steamer

• Cleaning Monthly PM tasks
• For monthly cleaning, follow the same steps as
  for daily
• cleaning and add the following steps
• Pour a solution of McD DelimerTM (one packet per
  16 oz of hot water) into steamer chamber and
  allow to soak for 15 minutes.
• Use brushes to clean water tube.
• Remove delimer solution and rinse steam chamber
  with clean water.

23
625-Series Rapid Steamer

• Cleaning Notes
• It is recommended that the steamers go through a
  deliming procedure at least once a month. Some
  hard water areas may require daily, weekly, or
  biweekly deliming based upon actual buildup.
• In areas affected by very hard water, a reverse
  osmosis (RO) water filtration system is an option
  to reduce accumulation of mineral deposits in the
  steamer. Contact is a KES or Coca-Cola for
  recommendations.

24
625-Series Rapid Steamer

• Cleaning Cautions
• Turn the unit off and unplug the power cord
  before cleaning. Unit is still HOT!
• The unit is NOT watertight. Do not clean with
  jet spray or spray directly on unit. Do not
  immerse unit in water.
• Do not use abrasive materials such as
  scrappers, steel wool, etc. to clean spatula or
  steam chamber.

!
!
!
25
625-Series Rapid Steamer
26
625-Series Rapid Steamer

• Warranty
• Two years parts and labor.
• Two years on-site service (100 miles roundtrip)
• Does not cover water tube, part no. 625-197S
• Service must be performed by an authorized
  service technician.

27
625-Series Rapid Steamer

• Troubleshooting Before contacting a service
  technician...
• Check the rear of the unit for the model and
  serial number.
• Check with store manager for the date of
  installation of the unit.

Model Number
Serial Number
28
625-Series Rapid Steamer

• Troubleshooting Before contacting a service
  technician...
• Identify the following symptoms
• Does the unit heat?
• Does the display work?
• Is the power switch illuminated?
• Does the unit produce steam?
• Is the water pressure set correctly?
• Is water getting to the unit?
• Is the metal water tube clean and free of lime?

29
625-Series Rapid Steamer

• When you have identified the steamers symptoms,
  please contact an authorized Service Agent in
  your area.
• To find an authorized Service Agent, go to the
  Prince Castle website at
• http//www.princecastle.com
• Or call Prince Castle at 1-630-462-8800 or toll
  free at 1-800-323-2930.