Bullard PA30 Series PAPR

1
Bullard PA30 Series PAPR

• Use and Care
• Training Presentation

2
PA30 Training Presentation Disclaimer

• This training presentation is intended as a
  supplement, NOT a replacement, to the information
  provided in the User Manual. Please read the
  entire User Manual prior to using the PA30 in any
  environment.

3
PA30 Principle of Operation

• A PA30 Powered Air Purifying Respirator System
  consists of four components
• Hood
• Breathing Tube
• Blower Assembly
• Filters / Cartridges

CARTRIDGES
4
PA30 Principle of Operation

• Battery Powered Belt Mounted Blower Unit draws
  air through three (3) cartridges connected to
  Blower Housing
• Filtered Air is delivered through the breathing
  tube and into the workers hood
• A design minimum of 7.5 cubic feet per minute
  (cfm) is delivered to the hood NIOSH requires
  only 6 cfm

5
Proper Use Warnings

• Know the work environment and the potential
  hazards that could exist.
• Do not use in atmospheres considered immediately
  dangerous to life or health (IDLH) as defined in
  29CFR 1910.134 (b).
• Leave area immediately if
• Breathing becomes difficult
• Dizziness or other distress occur
• You taste or smell the contaminant
• Unit becomes damaged
• Battery alarm sounds
• This apparatus must not be used with the blower
  unit switched off. If the blower is switched off,
  a rapid build-up of carbon dioxide and depletion
  of oxygen may occur, which could result in death
  or serious injury.
• Never alter or modify this respirator.
• Use only NIOSH-approved Bullard components and
  replacement parts for this respirator.
• Do not use in atmospheres containing less than
  19.5 oxygen.

6
Assembly

• Secure suspension into hood by snapping into
  place
• Attach Breathing Tube to Blower Unit, insuring
  gray seal is in place (below)
• Make sure that cartridges and batteries are
  installed on blower unit
• Attach the other end of the breathing tube to the
  hood by inserting the tube into the sleeve on the
  hood approximately 5 and securing with the
  anchor plate and clamp (right)

7
Pre-Operational Inspection

• Ensure that the Blower Unit and Hood are clean
  and free from damage
• Insure that all components are present for
  operation
• Inspect for Deterioration, Physical Damage, and
  Improper Assembly
• Check for proper airflow using the air flow
  indicator

8
Donning / Doffing

• Follow proper assembly and pre-operational
  instructions
• Donning / doffing should take place in a clean,
  hazard-free environment
• Place the blower unit and belt around the users
  waist and adjust the belt for a proper fit
• Turn on the blower unit
• Place the hood on the head and adjust the
  suspension for a comfortable and secure fit

9
Low Voltage Audible Alarm

• The alarm may indicate
• Low Battery Voltage
• Clogged or Damaged Canisters
• Blower Malfunction
• Breathing Tube or Hood Malfunction
• If the alarm sounds, exit the work area
  immediately and review User Manual for
  Troubleshooting guidelines

10
Charging the Batteries

• Place battery into charging port on the 2-port
  charger, or 5-port gang charger
• The LED indicator will remain solid green while
  charging.
• Allow the battery to fully charge the LED
  indicator will flash when the battery is fully
  charged
• Observe additional battery charging and care
  precautions in the User Manual
• After periods of extended storage or non-use,
  please refer to the User Manual for special
  charging procedure

11
Filters / Cartridges

• Replace PA3HE Filters when Air Flow Indicator
  indicates insufficient airflow, or when
  administrative schedule dictates
• Replace other Bullard cartridge types (PA3OVAGHE,
  PA3NBC) cartridges based on the required change
  out schedule which may be based on estimated
  service life, or administrative protocol

12
Additional Questions??
Contact Bullard at info_at_bullard.com or
1-877-BULLARD