FRIGI-TECH

1
FRIGI-TECH REFLECTIVE ROOF COATINGS
2
MAIN BENIFITS

• INSULATES Outperforms 7 of fiberglass
  insulation. Keeps interiors cooler and more
  comfortable. CUTS COST of air conditioning by up
  to 40. Increase in storage capacity of fuel
  storage tanks.
• INHIBITS RUST Prevents perforation and damage
  due to corrosion.
• PROTECTS - against UV, chemical damage. Is not
  affected by high winds or rain. Resists Mildew
  and algae.
• REDUCES THERMAL SHOCK - by lowering roof
  temperatures by as much as 60 degrees. This
  translates to less expansion/contraction and less
  stress and wear on fasteners and connections.
• WATERPROOF Stops leaks and prevents moisture
  absorption on all surfaces.
• FIRE RETARDANT Zero flame spread.
• IMPROVES APPEARANCE - with an extremely durable
  elastomeric finish that will not crack, chip, or
  peel. Can be tinted any color. Cuts your
  maintenance cost.
• ENVIRONMENTALLY SAFE No asbestos, lead, vinyl
  acetate, plastics, oils, odors or gases. Wash
  with water.
• ENCAPSULATES - asbestos surfaces and existing
  hazardous coatings.

3
APPLICATIONSAny surface that heat needs to stay
in or out of.

• Metal
• Concrete
• Asphalt
• Rubber

• Glass
• Tar and Gravel
• Wood Shingle

4
ENERGY STAR APPROVAL

• ENERGY STAR is a U.S. government-backed program
  helping businesses and individuals protect the
  environment through superior energy efficiency.

5
PRODUCTS

• FRIGI-TECH TOP COAT
• FRIGI-TECH TOP COAT II
• FRIGI-TECH PRIMER
• POLYESTER MEMBRANE

6
TOP COAT

• An Acrylic white coating with nearly 400
  elongation. Ideal for metal, built-up roofs with
  good drainage, shingles and all types of walls.
  Produces a tough washable coat that reduces dirt
  pick-up and stays cool with ceramic ingredient.

7
TOP COAT II

• All of the qualities of TOP COAT original with
  the added ability to resist standing water
  conditions. To be used on all surfaces in area
  that experience high humidity. Can reduce heat
  gain as efficiently as 7 inches of conventional
  insulation

8
PRIMER

• 100 acrylic, Elastomeric roof mastic formulated
  to exhibit hi-adhesion and flexibility. For use
  over most types of roof and wall surfaces.
  Recommended for use on all foam roofs.

9
POLYESTER MEMBRANE

• A spun bound and woven 100 polyester fabric,
  which is embedded into the basecoat to prevent
  extreme movement by greatly increasing the
  tensile strength of the system.

10
PROPERTIES
PRIMER TC I TC II ASPHALT
Viscosity 90 105 137 110
Total Solids 50 50 55 53
Permeance 5.0 9.0 17 30
Tensile P.S.I. 92 215 395 150
Elongation 600 380 400 2000
Flex 0?F Pass Pass Pass Pass
11
Solar Reflective
Modified Bitumen Black 6.8 Modified Bitumen TOPCOAT 88.4 Concrete Painted 24.0 Concrete Painted w/ TOPCOAT 87.1 Galvanized Metal 29.4 Galvanized Metal TOPCOAT 88.0
12
METAL ROOF APPLICATION

• VISUAL INSPECTION and REPLACEMENT of DAMAGED
  BUILDING MATERIALSThe substrate to be coated
  must be in SOUND condition. Physically inspect
  the surface area for missing or damaged building
  materials. Replace and/or repair all damaged
  areas back to sound and solid condition.Check
  for loose or missing fasteners (screws) and
  tighten or replace them.Inspect for any existing
  leaks and be sure to repair leaks prior to the
  application of coating.Make sure roof is
  adequately vented. Check with a roofing
  contractor if necessary.

13
METAL ROOF APPLICATION

• STEP2 PRESSURE CLEANINGHigh Pressure Blast
  entire roof surface with at least 1500 P.S.I. of
  pressure using a water and chlorine solution (1
  quart chlorine to 5 gallons of water). Thoroughly
  remove all dirt, oil, grease, residues, mold,
  mildew, algae and any other surface contaminants.
  When roof is completely cleaned, rinse with water
  only. Let roof surface dry before continuing.

14
METAL ROOF APPLICATION

• First Spot Prime all rusted areas and let dry at
  least 12 hours before applying the second coat of
  rust inhibitor to the effected area. Apply the
  rust inhibitor at a rate of 125-150 square feet
  per gallon covering the entire rusted surface.
  Wet film thickness of 10-12 mils wet resulting in
  dry film thickness of 7-9 mils. Let the rust
  inhibitor dry at least 12 hours before continuing

15
METAL ROOF APPLICATION

• STEP4 CAULKING SCREWSPatch and Caulk all
  screws or fastener heads, cracks, crevices,
  fractures, holes, valleys, vents, voids, etc.,
  with a Water Proofing caulk. Use a trowel or
  stiff brush to apply. Multiple coats are better
  than one thick coat if possible.

16
METAL ROOF APPLICATION

• STEP 5 TAPING SEAMS Tape all visible seams,
  large cracks and fractures prone to water
  intrusion on roof surface. Apply a liberal coat
  of PRIMER at 10-12 mils wet film thickness,
  directly to the affected area using brush, roller
  or airless spray and lay the POLYESTER MEMBRANE
  directly into the WET PRIMER.

17
METAL ROOF APPLICATION

• STEP6 PRIME COATApply PRIMER using 1- brush,
  2- at least a one inch nap roller, or 3- at least
  a 1 gallon per minute, 3,000 P.S.I. piston type
  airless sprayer with a minimum tip size of .027
  tip.

18
METAL ROOF APPLICATION

• Apply the PRIMER at a rate of 125-150 square feet
  per gallon covering the entire roof surface. Wet
  film thickness of 10-12 mils wet resulting in dry
  film thickness of 7-9 mils. Let PRIMER dry at
  least 12 hours before continuing.

19
METAL ROOF APPLICATION

• STEP 7 FIRST COAT of FINISH/TOP COATWhen
  Spraying or Rolling TOP COAT the first coat of
  TOP COAT must be applied perpendicular to the
  coat of PRIMER to achieve a checkerboard pattern.
  Apply the first coat of TOP COAT at a rate of
  100-125 square feet per gallon per coat over the
  entire roof surface. Wet film thickness of 12-15
  mils resulting in dry film thickness of 8-10
  mils.

20
METAL ROOF APPLICATION

• STEP 8 SECOND COAT of FINISH/TOP COATApply the
  second coat of TOP COAT at a rate of 100-125
  square feet per gallon per coat over the entire
  roof surface. Wet film thickness of 12-15 mils
  resulting in dry film thickness of 8-10 mils. Let
  dry at least 24 hours before your Final
  Evaluation

21
METAL ROOF APPLICATION

• STEP 9 FINAL EVALUATIONA detailed evaluation
  of the completed job will determine the quality
  of the workmanship and whether strict application
  specifications have been met. Be sure to check
  that all roof areas are completely coated and
  sealed under permanently placed roof items such
  as roof top air conditioning units. Divide roof
  into 1,000 square feet sections and randomly
  check one spot in each section for a dry film
  thickness of at least 20 mils. If specifications
  have not been met, determine how much material
  will be required to meet specifications and
  recoat.

22
EXAMPLES
23
EXAMPLES
24
BEFORE AND AFTER