Warm-Up

1
Warm-Up

• Explain when you would use the Belt/Disc sander
  versus the Oscillating Spindle Sander

2
Answer

• Belt/Disc Sander Sanding straight lines and
  convex (outside) curves
• Oscillating Spindle Sander Sanding concave
  (inside) curves

3
Warm-Up

• What type of edge do you need in order to glue-up
  two boards correctly (flat)

4
Answer

• Before gluing two boards together, make sure both
  mating edges are straight, square and true
• Use jointer again if needed to correct any gaps
• Make sure you test fit boards before applying
  glue
• Use a square to edge for being square

5
Warm-Up

• Why is it important to surface plane your lumber
  to a dimension thicker than your final dimensions
  when you are gluing your boards together?

6
Answer

• Leaving your boards thicker before gluing up
  allows you to be able to surface plane your
  boards AFTER you have glued them up to remove
  glue, flatten them out, and smooth the surface.

7
Warm-Up

• Name three uses of the combination square for
  your laying out your footstool

8
Answer

• Making the same measurement more than once
• Checking each piece for square
• Checking the depth of your mortise to see if it
  is consistent

9
Warm-Up

• After gluing AND unclamping your lumber, what is
  the next step

10
Answer

• Surface Plane to the FINISHED THICKNESS
• ¾
• JOINT an EDGE square AND straight
• RIP to FINISHED WIDTH

11
Warm-Up

• After Planing your lumber to THICKNESS and
  RIPPING to FINISHED WIDTH, what is the next step?

12
Answer

• CROSSCUT to the FINISHED LENGTH
• Use the Radial Arm Saw OR Sliding Compound Miter
  Saw

13
Process

1. Joint Face
2. Joint Edge
3. Surface Plane to ROUGH THICKNESS
4. Glue-Up
5. Surface Plane to FINISHED THICKNESS
6. Joint Edge
7. Rip to FINISHED WIDTH

14
Warm-Up

• After jointing, planing, ripping, and
  crosscutting to the finished width AND
  length..WHAT IS THE NEXT STEP?

15
Answer

• Layout your Joints
• Dado and Mortise
• Layout Irregular Shapes
• Radius Corners
• Handle
• Foot Curve

16
Process

1. Joint Face
2. Joint Edge
3. Surface Plane to ROUGH THICKNESS
4. Glue-Up
5. Surface Plane to FINISHED THICKNESS
6. Joint Edge
7. Rip to FINISHED WIDTH
8. Layout JOINTS and IRREGULAR SHAPES
9. CUT JOINT and IRREGULAR SHAPES

17
Warm-Up

• What makes a rabbet different than a dado joint?

18
Answer

• Dado u-shaped cut across the grain
• Rabbet L-shaped cut with or across the grain

19
Warm-Up

• Name 2 tools that can be used to cut a Dado or
  Rabbet?

20
Answer

• Tools used to cut a Rabbet or Dado Joint
• Table Saw
• Single Blade, Stacked Dado Blade, Wobble Dado
  Blade
• Router
• Radial Arm Saw
• Single Blade, Stacked Dado Blade
• Slide Compound Miter Saw
• Jointer
• Rabbet ONLY
• Hand Saw Chisel

21
Warm-Up

• List the sequence of cuts for cutting a mortise
  with a chisel

22
Answer

• Stop Cut across the grain
• Define the outline
• Spacer Cuts defines the depth
• Clearing Cuts removes material
• Remember!
• Always cut with the Bevel on the waste side of
  the line down
• Remove only a 1/8 thick cut each time
• Too much and you will split your wood

23
Answer Continued
24
Warm-Up

• Name the parts of a chisel

25
Answer
Butt
Handle
Socket
Ferule
Blade
Bevel
26
Work Area

• YOU MUST WORK AT YOUR ASSIGNED WORK BENCH
• --
• NO WATER DRINKS!

27
Warm-Up

• What steps can you take to eliminate burn-marks
  when routing your work piece?

28
Answer

• To PREVENT Router burn-marks
• Keep the router moving
• Too slow and you burn the wood
• Hold the router firmly and tightly against the
  wood
• Clamp the work piece
• Take small passes 1/8 at a time
• Take an even smaller pass as your final pass

29
Warm-Up

1. Name the Machine Label Each Part
2. What is it used for?

30
Jointer flatten straighten wood
OutFeed Table
Fence
Guard
InFeed Table
InFeed Table Lock
Infeed Table Wheel
On/Off
????
31
Warm-Up

• Name the Tool
• Explain its Use
• Identify the Parts

32
Surface Planer creates parallel face to
thickness
Bed Roller Lever
On/Off
InFeed Table
Speed Wheel
Table Adjustment
33
Warm-Up

• Name the Tool
• Explain its Use
• Identify the Parts

34
Table Saw RIPS parallel edges
Splitter
Table
Fence
Blade Height Wheel
On/Off
35
Warm-Up

• Name the Tool
• Explain its Use
• Identify the Parts

36
Radial Arm Saw Crosscuts
On/Off
Blade
Table
Fence
37
Warm-Up

• Calculate the BOARD FEET in the following cut
  list
• 6 x 48 x 1 Walnut
• 7 x 36 x 1 Walnut
• 3 x 34 x 1 Walnut
• 9 x 14 x 1 Walnut
• Walnut 4.35 per board foot
• BF W x L x H / 144

38
Answer

• Calculate the BOARD FEET in the following cut
  list
• 6 x 48 x 1 Walnut
• 7 x 36 x 1 Walnut
• 3 x 34 x 1 Walnut
• 9 x 14 x 1 Walnut
• Walnut 4.35 per board foot
• BF W x L x H / 144

288/144 2 BF
252/144 1.75 BF
102/144 .70 BF
126/144 .875 BF
TOTAL 5.325 BF
x 4.35
23.16
39
Warm-Up

• Calculate the BOARD FEET in the following cut
  list
• 8 x 48 x 3 Walnut
• Walnut 4.35 per board foot
• BF W x L x H / 144

40
Answer

• Calculate the BOARD FEET in the following cut
  list
• 8 x 48 x 3 Walnut
• Walnut 4.35 per board foot
• BF W x L x H / 144

1152/144 8 BF
TOTAL 8 BF
x 4.35
34.80