Blank Jeopardy

1
Bench Grinder
Drill Press
Table Saw
General
Oxy- acetylene
100 pt
100 pt
100 pt
100 pt
100 pt
200 pt
200 pt
200pt
200 pt
200 pt
300 pt
300 pt
300 pt
300 pt
300 pt
400 pt
400 pt
400 pt
400 pt
400 pt
500 pt
500 pt
500 pt
500 pt
500 pt
2
Bench Grinder
Stand here when turning on the grinder.
3
Bench Grinder
What is stand to the side?
4
Bench Grinder
Grind metal on the proper surface of the wheel.
5
Bench Grinder
What is grind on the face of the wheel, not the
side?
6
Bench Grinder
The best tool to hold metal when grinding.
7
Bench Grinder
What is vice-grips?
8
Bench Grinder
When finished grinding, turn off the machine and
wait for wheels to stop.
9
Bench Grinder
What is dont stop the grinding wheel by forcing
metal into it?
10
Bench Grinder
Properly position the tool rest to the grinding
wheel.
11
Bench Grinder
What is 1/8 away and in the center of the wheel?
12
Drill Press

• Technique used to keep the bit cool while
  drilling.

13
Drill Press

• What is squirt cutting fluid on the bit while
  drilling?

14
Drill Press

• Used to tighten or loosen the chuck and bit.

15
Drill Press

• What is the chuck key?

16
Drill Press

• Some materials should be secured with a vice or
  clamp when drilling.

17
Drill Press

• What are small or awkward pieces of wood or
  metal?

18
Drill Press

• Changing bit speed on the drill press.

19
Drill Press

• What is unplug the machine and adjust the belts?

20
Drill Press

• The rule of thumb for speed adjustment when
  drilling.

21
Drill Press

• What is drill slower in metal and faster in wood?

22
Table Saw

• Stand on the right side of the blade

23
Table Saw

• Where is the correct place to stand when
  operating the table saw?

24
Table Saw

• The proper blade height above the wood.

25
Table Saw

• What is ¼ or less?

26
Table Saw

• This tool is required in ripping boards less than
  6 inches wide.

27
Table Saw

• What is a push stick?

28
Table Saw

• A guide used to cut boards to an accurate width
  on the table saw.

29
Table Saw

• What is the Rip Fence?

30
Table Saw

• Small piece of metal with ridged teeth on the
  back side of the blade.

31
Table Saw

• What us kick back prevention device?

32
General

• Proper safety for eyes.

33
General

• What is wear safety glasses at all times in the
  shop?

34
General

• Before adjusting power tools and machines.

35
General

• What is unplug by pulling on the plug, not the
  cord?

36
General

• Oil is spilled on the shop floor.

37
General

• What is clean up immediately and use floor dry if
  available?

38
General

• Keep adequate ventilation in the paint room.

39
General

• What is close the door and turn on the fan
  (possible crack windows)?

40
General

• Be responsible for what you purchase or bring to
  the shop.

41
General

• What is put your name on all project materials?

42
Oxyacetylene

• You should consider this material to be hot at
  all times.

43
Oxyacetylene

• What is metal laying in the shop in the welding
  area?

44
Oxyacetylene

• Color of hose and cylinder for oxygen.

45
Oxyacetylene

• What is green?

46
Oxyacetylene

• Uses flint to create a spark.

47
Oxyacetylene

• What is a striker?

48
Oxyacetylene

• Flame with more oxygen than acetylene.

49
Oxyacetylene

• What is oxidizing?

50
Oxyacetylene

• Used to heat large pieces of metal.

51
Oxyacetylene

• What is a rose bud tip?

52
Final Jeopardy

• Category Band Saw

53
Final Jeopardy

• Answer Cuts made perpendicular to the actual
  line to make cutting easier.