How to configure DCNNG

1
How to configure DCNNG Stand Alone Camera
Control

• This presentation is intended to guide the
  installer step by step through camera control
  installation.

DCNNG CC
2
How to configure DCNNG Stand Alone Camera
Control

• DCN-CCUB with direct Camera Control Virtual
  Keyboard
• DCN-CCUB with direct Camera Control Autodome
  Controller
• DCN-CCUB with Allegiant Video Switcher
• DCN-CCU with direct Camera Virtual Keyboard
• DCN-CCU with direct Camera Control Autodome
  Controller
• DCN-CCU with Allegiant Video Switcher

3
DCN-CCUB with direct Camera Control Virtual
Keyboard

• Requirements
• One AutoDome Camera
• One monitor
• Virtual keyboard software LTC 5138/00
• DCN-CCUB
• Temporary Installation PC
• Camera Control Software LBB 4162/xx

4
Step 1

• Connecting PC and Monitor to AutoDome Camera

Make sure that the Dome camera has an address.
RS232
Temporary Installation PC
IU Instructions
5
Step 2

• Install virtual keyboard software LTC 5138/00

AutoDome Camera
Temporary Installation PC
IU Instructions
6
Step 3

• Configure Virtual Keyboard

7
Step 4

• Communication Setup

8
Step 5

• Make sure you choose the right camera!

9
Step 6
10
Step 7

• Quick Commands settings

11
Step 8

• Pre-Position Title Set

12
Step 9

• Set Pre-Positions

13
Step 10

• Pre-Position Shot Name

14
Repeat
Repeat Steps 9 10 to set all Pre-Positions
Set the highest Pre-Position as overview
15
Step 11

• Check the Pre-Positions

To NEXT gtgtgtgtgtgt
16
End of how to configure

• DCN-CCUB with direct Camera Control Virtual
  Keyboard
• DCN-CCUB with direct Camera Control Autodome
  Controller
• DCN-CCUB with Allegiant Video Switcher
• DCN-CCU with direct Camera Virtual Keyboard
• DCN-CCU with direct Camera Control Autodome
  Controller
• DCN-CCU with Allegiant Video Switcher

17
DCN-CCUB with direct Camera Control Autodome
Controller

• Requirements
• One AutoDome Camera
• One monitor
• Autodome Controller LTC 5136/51
• DCN-CCUB
• Temporary Installation PC
• Camera Control Software LBB 4162/xx

18
Step 1

• Only for Pre setting the Autodome Camera with
  the Autodome Controller
• Connect Autodome Controller to data converter LTC
  5136/51
• Connect Data converter to Aurodome Camera
• Connect Autodome Camera to Monitor

AutoDome Camera
Data Converter
Temporary Autodome Controller
IUI Autodome
19
Remark

• If you were not successful setting up the
  pre-positions please dont continue with the next
  steps.
• First make sure that the pre-positions are set.

20
Step 2

• Connect CCUB to PC

RS232
Temporary Installation PC
Port 1 Camera Control Protocol Baudrate 9.6K
IU Instructions
21
Step 3

• CCU protocol and Serial Port settings DCN-CCUB

Make sure that the ports of the CCU are set
correct.
Port 1You have to change the port
settings! Protocol Camera ControlBaudrate
9.6K
IU Instructions
22
Step 4

• Install DCNNG Stand Alone Camera Control software
  LBB4162

23
Step 5

• Install Camera Control software LBB4162

24
Step 6

• Install Camera Control software LBB4162

25
Step 7

• Install Camera Control software LBB4162

26
Step 8

• Select the language for operator

27
Step 9

• Select no use of Allegiant VideoSwitcher

28
Step 10

• Installing DCNNG Stand Alone Camera Control
  software LBB4162

29
Step 11

• Finish installation

30
Step 12

• Start DCN Next Generation Camera Install

31
Step 13

• Combine seat numbers with camera pre positions

LBB4162
32
Step 14

• Make sure you choose the right camera!!Camera nr
  Camera Address

LBB4162
33
Step 15

• Insert

LBB4162
34
Step 16

• Stop Camera Installation

LBB4162
35
Step 17

• Connect CCUB to AutoDome Camera

AutoDome Camera
RS232
Port 1 Camera Control Protocol Baudrate 9.6K
Baudrate 9.6K
IU Instructions
36
End of how to configure

• DCN-CCUB with direct Camera Control Autodome
  Controller
• DCN-CCUB with Allegiant Video Switcher
• DCN-CCU with direct Camera Virtual Keyboard
• DCN-CCU with direct Camera Control Autodome
  Controller
• DCN-CCU with Allegiant Video Switcher

37
DCN-CCUB with Allegiant Video Switcher

• Requirements
• Allegiant switcher
• Video Switcher keyboard
• Fixed and/or AutoDome cameras
• Monitor(s)
• DCN-CCUB
• Temporary Installation PC
• Camera Control Software LBB 4162/xx

38
Step 1

• Connecting system hardware

BOSCH
Temporary Installation PC
39
Step 2

• Connect DCN-CCUB Allegiant Switcher to
  Temporary PC

Camera Control Protocol
RS232
RS232
Allegiant Switcher
Baudrate 19.2K
Baudrate 19.2K
IU Instructions
40
Step 3

• CCU protocol and Serial Port settings DCN-CCUB

Make sure that the ports of the CCU are set
correct.
Port 1You have to change the port
settings! Protocol Camera ControlBaudrate
19.2K
IU Instructions
41
Step 4

• Install DCNNG Stand Alone Camera Control software
  LBB4162

42
Step 5

• Installing DCNNG Stand Alone Camera Control
  software LBB4162

43
Step 6

• Installing DCNNG Stand Alone Camera Control
  software LBB4162

44
Step 7

• Installing DCNNG Stand Alone Camera Control
  software LBB4162

45
Step 8

• Select the language for operator

46
Step 9

• Select use Allegiant VideoSwitcher

47
Step 10

• Installing DCNNG Stand Alone Camera Control
  software LBB4162

48
Step 11

• Finish installation

49
Step 12

• Set Pre-Positions using the Video Switcher
  Keyboard

50
Step 13

• Start DCN Next Generation Camera Install

51
Step 14

• Combine seat numbers with camera pre positions

LBB4162
52
Step 15

• Make sure you choose the right camera!!Camera nr
  Camera Address

LBB4162
53
Step 16

• Insert

LBB4162
54
Step 17

• Stop Camera Installation

LBB4162
55
Step 19

• Connecting hardware (Remove temporary PC!)

See next slide
BOSCH
56
Step 19

• Connection cable between CCU and Allegiant
  Switcher

IU Instructions
57
End of how to configure

• DCN-CCUB with Allegiant Video Switcher
• DCN-CCU with direct Camera Virtual Keyboard
• DCN-CCU with direct Camera Control Autodome
  Controller
• DCN-CCU with Allegiant Video Switcher

58
DCN-CCU with direct Camera Virtual Keyboard

• Requirements
• One AutoDome Camera
• One monitor
• Virtual keyboard software LTC 5138/00
• DCN-CCU
• Temporary Installation PC
• Camera Control Software LBB 4162/xx

59
Step 1

• Connect PC and Monitor to the Dome Camera

Make sure that the Dome camera has an address.
RS232
Temporary Installation PC
IU Instructions
60
Step 2

• Install virtual keyboard software LTC 5138/00

Temporary Installation PC
IU Instructions
61
Step 3

• Configure Virtual Keyboard

62
Step 4

• Communication Setup

63
Step 5

• Make sure you choose the right camera!!

64
Step 6
65
Step 7

• Quick Commands settings

66
Step 8

• Pre-Position Title Set

67
Step 9

• Set Pre-Positions

68
Step 10
69
Repeat
Repeat Step 9 10 to set all Pre-Positions
Set the highest Pre-Position as overview
70
Step 11

• Check the Pre-Positions

To NEXT gtgtgtgtgtgt
71
End of how to configure

• DCN-CCU with direct Camera Virtual Keyboard
• DCN-CCU with direct Camera Control Autodome
  Controller
• DCN-CCU with Allegiant Video Switcher

72
DCN-CCU with direct Camera Control Autodome
Controller

• Requirements
• One AutoDome camera
• Monitor(s)
• Autodome Controller LTC 5136/51
• DCN-CCU
• Temporary Installation PC
• Camera Control Software LBB 4162/xx

73
Step 1

• Only for Pre setting the Autodome Camera with
  the Autodome Controller
• Connect Autodome Controller to data converter LTC
  5136/51
• Connect Data converter to Aurodome Camera
• Connect Autodome Camera to Monitor

Data Converter
Temporary Autodome Controller
IUI Autodome
74
Remark

• If you were not successful setting up the
  pre-positions please dont continue with the next
  steps.
• First make sure that the pre-positions are set.

75
Step 2

• Connect CCU to PC

RS232
Temporary Installation PC
Port 2 Camera Control Protocol Baudrate 9.6K
IU Instructions
76
Step 3

• CCU protocol and Serial Port settings DCN-CCU

Make sure that the ports of the CCU are set
correct.
Port 1Protocol FullBaudrate 115.2K Port
2Protocol Camera ControlBaudrate 9.6K
S500 Dip switches
Keep in mind !!
You have to change the baudrate of Port 2 to 9.6K
!!
IU Instructions
77
Step 4

• Make sure you connect the RS232 cable to Port 2
  of the DCN-CCU.

78
Step 5

• Install DCNNG Stand Alone Camera Control software
  LBB4162

79
Step 6

• Install Camera Control software LBB4162

80
Step 7

• Install Camera Control software LBB4162

81
Step 8

• Install Camera Control software LBB4162

82
Step 9

• Select the language for operator

83
Step 10

• Select no use of Allegiant VideoSwitcher

84
Step 11

• Installing DCNNG Stand Alone Camera Control
  software LBB4162

85
Step 12

• Finish installation

86
Step 13

• Start DCN Next Generation Camera Install

87
Step 14

• Combine seat numbers with camera pre positions

LBB4162
88
Step 15

• Make sure you choose the right camera!!Camera nr
  Camera Address

LBB4162
89
Step 16

• Insert

LBB4162
90
Step 17

• Stop Camera Installation

LBB4162
91
Step 18

• Connect CCU to AutoDome Camera

RS232
Port 2 Camera Control Protocol Baudrate 9.6K
Baudrate 9.6K
IU Instructions
92
End of how to configure

• DCN-CCU with direct Camera Control Autodome
  Controller
• DCN-CCU with Allegiant Video Switcher

93
DCN-CCU with Allegiant Video Switcher

• Requirements
• Allegiant switcher
• Video Switcher keyboard
• Fixed and/or AutoDome cameras
• Monitor(s)
• DCN-CCU
• Temporary Installation PC
• Camera Control Software LBB 4162/xx

94
Step 1

• Connecting system hardware

BOSCH
Temporary Installation PC
95
Step 2

• Connect DCN-CCU Allegiant Switcher to
  Temporary PC

Port 2 Camera Control Protocol
RS232
RS232
Allegiant Switcher
Baudrate 19.2K
Baudrate 19.2K
IU Instructions
96
Step 3

• CCU protocol and Serial Port settings DCN-CCU

Make sure that the ports of the CCU are set
correct.
Port 1Protocol FullBaudrate 115.2K Port
2Protocol Camera ControlBaudrate 19.2K
S500 Dip switches
IU Instructions
97
Step 4

• Make sure you connect the RS232 cable to Port 2
  of the DCN-CCU.

98
Step 5

• Install DCNNG Stand Alone Camera Control software
  LBB4162

99
Step 6

• Installing DCNNG Stand Alone Camera Control
  software LBB4162

100
Step 7

• Installing DCNNG Stand Alone Camera Control
  software LBB4162

101
Step 8

• Installing DCNNG Stand Alone Camera Control
  software LBB4162

102
Step 9

• Select the language for operator

103
Step 10

• Select use Allegiant VideoSwitcher

104
Step 11

• Installing DCNNG Stand Alone Camera Control
  software LBB4162

105
Step 12

• Finish installation

106
Step 13

• Set Pre-Positions using the Video Switcher
  Keyboard

107
Step 14

• Start DCN Next Generation Camera Install

108
Step 15

• Combine seat numbers with camera pre positions

LBB4162
109
Step 16

• Make sure you choose the right camera!!Camera nr
  Camera Address

LBB4162
110
Step 17

• Insert

LBB4162
111
Step 18

• Stop Camera Installation

LBB4162
112
Step 19

• Connecting hardware (Remove temporary PC!)

See next slide
BOSCH
113
Step 20

• Connection cable between CCU and Allegiant
  Switcher

IU Instructions
114
End of how to configure

• DCN-CCU with Allegiant Video Switcher

DCNNG CC