Proprietary InformationDo Not Duplicate Manual' - PowerPoint PPT Presentation

Title: Proprietary InformationDo Not Duplicate Manual'


1
End User Training Manual Tandberg Video System
Proprietary Information-Do Not Duplicate Manual.
2
SECTION 2
Camera
Monitor (Far Site)
Natural Audio Module
Monitor (Near Site)
CODEC (in cabinet)
VCR
Microphone
Document Camera
Tracker
Remote Control
Integrator Visual Systems Group, Inc. Help Desk
888-882-7378 or 408-402-9090 Manufacturer Tand
berg System Software Version Serial
Number System Administrator Video/IP Number
3
SECTION 3
REMOTE CONTROL
4
Your system should be in standby mode. When in
standby mode, pressing any key or grasping the
remote control will wake up the system. An
incoming call will also wake up the system. If
the system does not respond, make sure the system
is switched on by using the On/Off switch located
at the rear of the Codec (see figure below).
After a few seconds you should see a start-up
message on the monitor. If this does not
help, verify that your monitor is switched on. To
switch the monitor on you normally push the power
button on the front of the monitor (depending on
monitor type).
Getting Started
Making a Call

• To make a call
• Press the CONNECT button on the remote control.
  The following screen will appear

• Use the number keys on the remote control to
  enter in the video number
• Press the BLUE quick key to select the
  appropriate line speed. The following screen
  will appear

• Use the GREEN Quick Key to select the line speed
  you would like to use for the call OR use the
  YELLOW Quick Key to set the desired line speed as
  your default so you do not have to repeat this
  step for future calls.

Line Speed Translator
Auto 6B on ISDN/768Kbps on LAN Max 12B on
ISDN/2Mbps on LAN 12 ch 768 Kbps 8 ch 512
Kbps 6 ch 384 Kbps 5 ch 320 Kbps 4 ch
256 Kbps 3 ch 192 Kbps 2 ch 128 Kbps 1 ch
64 Kbps Telephone Place Audio Call HO PRO
Only 1XHO (384 Kbps)
3-1
5
Making a Call

• Press the GREEN Quick Key to select the type of
  Network to be used for the call. He following
  screen will appear

• Use the arrow keys to select the type of network
  to be used and either the GREEN Quick Key to
  select it for the current call or the YELLOW
  Quick Key to set it as your default for all
  calls.

• Press Connect to place the call.

If you are not using all of your available
bandwidth, you can press the Connect button and
see the following screen
Additional Calling Options
You can Add a site into the call by pressing the
GREEN Quick Key. You can simultaneously send a
second video source by placing a Duo Video Call
and pressing the YELLOW Quick Key.
Disconnecting a Call
To disconnect a point-to-point video call, press
the disconnect button. The call will immediately
disconnect.
3-2
6
Adjusting Audio
Press the Mic Off button on the remote control to
mute your microphones. You will get an
indication on the screen that you microphones are
muted.
Press the Volume keys to adjust the volume level.
An on-screen indicator will show the current
level. NOTE It is important that you use the
system Volume control keys and not the monitor
remote control. Too high volume setting may
result in echo being experienced by the far end
of a videoconference.
Adjusting Cameras
The Main Camera can be controlled by the remote
control. If another PTZ (Pan/Tilt/Zoom) camera
has been connected to your system via the Aux
port, you can also control that one as well. To
control PTZ cameras

• Select the appropriate camera you wish to control
  (Main Cam or Aux)
• Use the arrow keys to Pan, Tilt, or Zoom the
  camera
• Use the Zoom Keys to zoom the camera in and out

Camera Presets

• The preset buttons enable you to pre-store up to
  ten different settings. Each preset is able to
  store
• Video source
• Camera position, pan/tilt/zoom/focus (if Main
  Camera)
• Selecting presets
• To select a pre-stored camera position, use the
  keys P1 P2 P3 or press P until the on-screen
  indicator Preset 0-9 appears and use 0-9 to
  activate P0-P9 presets.
• To exit Preset mode, press the BLUE Quick Key.
• P1-P3 are the same presets as when pressing P
  and then a number key 1-3.
• Storing presets

• To store a preset
• Position the camera and/or select a video source.
• Press STORE once.
• Then press one of the keys P1 P2 P3 or a number
  key 0-9.

3-4
7
Controlling the Far End Cameras
Press the Far End key until the Far End Camera
on-screen indicator is displayed. For this
feature to operate the far end must support Far
end camera control (H.281). While activated, you
will be able to control the far ends camera
(pan/tilt/zoom/focus) and presets.
Using the Tracker

• The Tracker is a small infrared remote control
  device made to steer the camera on the
• system to any desired location within the room.
  Typically, several Trackers are attached to each
  system.
• Each Tracker has two buttons
• One button to point the camera at one person.
• One button to point the camera at all
  participants.

Through Voice Activated Camera Positioning and
the use of two or three microphones, the camera
will automatically view the speaker. Setup Befor
e using camera tracking, the camera positions
used must be stored at presets P7 (Mic1), P8
(Mic2) and/ or P9 (Mic3). Example The camera
position stored at P7 must be related to Mic1,
therefore all participants which are located
closest to Mic1 should be included in the P7
camera position etc. When camera tracking is
activated and a person close to Mic1 speaks, P7
will be automatically selected. If a person close
to Mic1 has a conversation with a person close to
Mic2, the camera will adjust to a camera position
which includes both persons. Activating Enable
Camera Tracking by pressing the P button on the
remote control and then selecting the GREEN
Quick Key. An on-screen indicator CamTrackOn
will appear. When activating another video
source (e.g. document camera), camera tracking
will temporarily be disabled until you select
MainCam or a MainCam preset. Pressing MIC OFF
will temporarily disable camera tracking. A
Voice Detector makes the system more tolerant
against noise and the camera will normally not be
moved by noise like paper shuffling
etc. Deactivating Disable Camera Tracking
by moving the camera manually. activating a
MainCam preset when MainCam is already
activated. disconnecting the call. An
on-screen indicator CamTrackOff will
appear. Note The Start Camera Tracking entry
will be grayed out if not using the W.A.V.E.
Camera.
Automatic Camera Tracking
3-5
8
Displaying/ Transmitting Video Sources
To display or transmit between the 5 possible
video inputs, press the buttons
The document camera VCR must be manipulated via
their own controls. They cannot be controlled
through the remote control or with the software.
PC Presenter
Plugging a PC into the system is made extremely
simple through the PC Presenter, a direct access
plug on the front of the cabinet, avoiding the
need for any additional hardware such as a
projector, PC/Video converter or extra cables.

• Connect a VGA-VGA cable from your PC (VGA Output)
  to the PC Presenter connector in front of the
  system (behind the glass door).
• Start your PC.
• Press PC on your remote control.
• Press SELFVIEW until the indicator Selfview is
  displayed on your main monitor or until you see
  the PC image on the second monitor.
• If a PC image is not displayed on your monitor,
  make sure that your PC transmits the image to the
  VGA Output, and that the PC transmits a supported
  VGA-format. Consult your PC-operating manual to
  see how to transmit a VGA image from your PC.
• A VGA-VGA cable is located in the drawer above
  the codec if the Natural Presenter Package is
  included in your system.

Snapshot
When a still image is sent, received or
requested, it will be stored in the graphics
memory. When a new image is sent or received, the
old image will be erased. When disconnecting the
call, the image will be erased.

• To sent a snapshot,
• Select the video source you would like the till
  image to be taken from
• Press the Snapshot button.
• Press Self view to return to your image.

Self view/ Picture In Picture
Press the SELFVIEW key to see your own picture
(the outgoing image during a call). Pressing it
again will remove your self view from the
monitor. If you have a dual monitor system,
pressing the SELFVIEW key will ( in a call )
toggle between your self view and the last sent
or received still image on the dual
monitor. Press the MOVE PIP key to move your
SELFVIEW as Picture-in-Picture to different
corners of the screen or switch it off.
3-6
9
Duo Video

• Duo Video is useful if you want to display live
  video from your document camera or another camera
  in addition to live video of yourself.
• To Add Duo Video
• Press CONNECT during a call. This will bring up
  the following menu
• Select Add Duo Video. The following menu will be
  displayed
• If the far end does not support Duo Video, you
  will need to specify the Duo Video number. If
  supported, the number is found automatically and
  the number prompt is not displayed.

To end a Duo Video call, press DISCONNECT.
Select if you want to disconnect only the Duo
Video connection or the whole connection.
Multipoint Conferences
The system has a built-in multipoint conference
unit (MCU), MultiSite, which has the capability
to establish meetings with up to 4 sites. The
MultiSite supports both Voice Switched and
Continuous Presence mode. The sites in a
conference must be connected using the same
bandwidth.
Establishing a conference is done by first making
a call to one site. When a call is established
with the first site, the other sites are
connected one by one. It is possible to either
dial out to the sites or the sites can dial in to
the MultiSite.
3-7
10
Placing a Multipoint Call
Using the Dial Out Method First establish a
normal point-to-point call. It is recommended to
plan the channel usage before making the first
call so that you do not run out of
bandwidth. Example If the system has 8 channels
available and you want to connect 3 sites in
addition to the host, 2 channels should be
selected for the first call. The system will then
automatically use 2 channels when connecting the
other sites. When the first site is connected,
add a site to the conference by following the
procedure 1. Press CONNECT to bring up the
following menu 2. Press the GREEN Quick Key
to bring up the MultiSite dial menu. 3.
Enter the number to call. The Quality will be the
same as used by the first call. 4. Press
CONNECT. Add Site Add Duo Video Back
Using the Dial In Method To dial in to the
MultiSite, you must know the numbers to each of
ISDN BRIs Site 1 must dial Lint Number 1. Site 2
must dial Line Number 2. Site 3 must dial Line
Number 3. OR If using an ISDN PRI, the far sites
dial the normal ISDN-PRI number of the system.
All sites must dial the same number. To find the
ISDN line numbers, press the Menu button and go
to Diagnostics and View Current Settings When
the MultiSite receives an incoming call, the
following menu is displayed Use the Quick Keys
to enter the appropriate response, OR Pressing
CONNECT will be equivalent to pressing
Accept Pressing DISCONNECT will be equivalent to
pressing Reject Pressing Do Not Disturb will
disable the MultiSite from answering more
incoming calls during the current conference. The
calling party will receive a busy signal.
3-8
11
Disconnecting a MultiPoint Call
If you are in a multi-point call, you will see
the following screen when the disconnect button
is pressed
Use the arrow keys to select the site you would
like to disconnect and press the OK button or the
GREEN quick key. To disconnect the entire call,
select Terminate Meeting and press the OK button
or press the YELLOW quick key.
MCU Services
A Multipoint Control Unit (MCU) enables several
sites to participate in the same conference. An
MCU conference can have different modes Voice
Switched means that the image of the person
currently speaking will be broadcast to all the
other conference participants. This will remain
the case until another participant starts to
speak. Continuous Presence shows several
participants on the same screen at the same
time. Request floor When requesting
the floor, the MCU will broadcast your video in
full screen to all other participants in the
conference. If the MCU conference has a chairman,
a floor request is sent to the chairman. You will
remain On Air until either you select Release
Floor or the chairman decides to release the
floor to another participant. Release floor You
choose Release Floor to take you Off Air. You
should do this when you wish to make the
flooravailable to the other participants in the
conference. Terminal Names Allows you to see the
site numbers or name (if supported) of other
sites connected in the conference. View site
Allows you to view any participant in the
conference other than the participant currently
On Air. End view Allows you to stop viewing
the site previously chosen with View Site , and
returns your view to the site that is currently
On Air.
To get to the MCU Services Menu, Press the Menu
button on the remote control and select MCU
Services from the list of choices.
3-9
12
Chair Control
Chairman Control functionality enables one
participant to control the meeting by selecting
which of the conference participants is to be
broadcast to the other participants. This option
is not supported in a Tandberg MultiSite Meeting
It is available only when connected to and
external MCU that supports Chair Control (H.243).
Chair control You select Chair Control and Take
Chair to assume the role of chairman of the
meeting. Chair Control provides considerable
conference management functions. As chairman, you
may control which site you and the other sites
see. Take chair Allows you to request
chairmanship of the conference. If no one else is
currently chairman the MCU will give you the
chair. Release chair Allows you to relinquish
the privileges of chairmanship of the
conference. Floor to site Allows the chairman
to select which of the conference participants is
to be broadcast to all other participants. Releas
e Floor Allows the chairman to release the
floor. Disconnect site Allows the chairman to
disconnect any participant in the
conference. Terminate meeting Allows the
chairman to terminate the conference altogether.
Powering Down
The system is shut down by turning off the power
to the CODEC.
3-10