Model RJ-3 System Package

1
Res-Q-Jack Vehicle Stabilization
Model RJ-3 System Package We offer a Res-Q-Jack
Model RJ-3 3-point stabilization package system
which includes Qty. of (1) Jack Stand Kit with
pins, base and strapping Qty. of (2) Adjustable
Stand Kits each with pins, base and
strapping Note above package includes 3 end
fittings (see kit descriptions) This system is
recommended for use in passenger vehicle, farm
tractor, tractor cab, school bus stabilization.
The jack may also be used in dash displacement.

2
Res-Q-Jack Vehicle Stabilization
RJ-3 Jack Stand kit
The Jack Stand is an adjustable stand with
a sidewind jack incorporated as a means for fine
adjustment and/or loading. Jack design allows
for infinitesimal adjustment with no "jumping".
The pieces of the Jack Stand disassemble in
seconds allowing for quick reassembly in the
desired configuration. Jack Stand includes the
following components Qty. of (1) 4000 sidewind
jack (12" travel) Qty. of (1) Stand
Base with (2) cam straps Qty. of (1) 18" length
2" extension tubing Qty. of (1) 36" length 2"
extension tubing Qty. of (1) 24" length 2.25"
extension tubing Qty. of (3) grade 8 tablock
pins Qty. of (1) End Fitting (C-head, angle
head, or flat point head) Maximum extension
99, Assembled/Collapsed length 58 Max. piece
length disassembled 36, base width 5x6 Note
consider application and refer to component
strengths for load capabilities listed in
following information. Jack Stand weight 46 lbs.
3
Res-Q-Jack Vehicle Stabilization
RJ-3 Adjustable Stand kit The Adjustable Stand
is comprised of the following components Qty. of
(1) Stand Base with (2) cam buckle straps Qty. of
(1) 42" length 2" extension tubing Qty. of (1)
42" length 2.25" extension tubing Qty. of (1)
grade 8 tablock connection pins
Qty. of (1) End Fitting (choose 1 Chead, Angle
head, flat point head) Note if using
Adjustable Stands without a Jack Stand or in a
manner in which Jack Stand will not tighten
system strapping (cambuckle straps provided) a
ratchet strap may be employed at the auxiliary
hook points provided on base. Maximum extension
84, Assembled/Collapsed length 51 Max. piece
length disassembled 42, base width 5x6 Note
consider application and refer to component
strengths for load capabilities listed in
following information. Adjustable Stand weight
28 lbs.
4
Res-Q-Jack Vehicle Stabilization
RJ-3 Base Kit The Base is comprised of a 5" x 6"
x 3/16" diamond plate pad. A 6" length of 2"
telescopic perforated tubing is pivotally bolted
to uprights welded to the pad. This piece is
designed to accept a Jack Unit, another section
of tubing, or a custom adaptor. Two cam buckle
straps are attached to the pivot bolt. Optional
hook points are provided for use with a ratchet
strap or similar (not provided). In addition
four ½" diameter holes are provided on the base
pad for anchoring when desired. Includes (1)
tablock pin.
5
Res-Q-Jack Vehicle Stabilization
RJ-3 Jack Unit This jack is a sidewind type
jack. Infinitesimal adjustment is made possible
through the use of a threaded rod driven by the
sidewind crank handle. It is approximately 24"
long in its retracted position. A short length
of 2.25" perforated tubing is welded to the side
of the jack outer tube to allow for the insertion
of 2" extension tubing, end fittings, or custom
parts. The inner tube of the jack will accept a
base, a length of 2" tube, end fittings, or
custom parts. Wind right to extend, left to
retract. Jack holds position without
pinning. NOTE This jack is designed to be used
in compression, not as a winch (in tension). Do
not load while retracting. Jack lift capacity
4000 lbs. Note assembly capacity will depend on
attached component strength Jack travel
12 inches
6
Res-Q-Jack Vehicle Stabilization
RJ-3 Flat Point End Fitting
The Flat Point End Fitting is
convenient for gaining purchase in narrow pockets
where the larger profile end fitting may not be
suitable. RJ-3 C-Head End Fitting
The C-Head End
Fitting allows one to cradle relatively wide
members like an A' post to assure a positive
hold. RJ-3 Angle Head End Fitting
The Angle Head
End Fitting offers a narrow cradle which will
provide a good purchase on the corner of various
structural members. NOTE End fittings are
designed with a step which allows a snug fit in
either size extension tubing. Each includes (1)
tablock pin.
7
Res-Q-Jack Vehicle Stabilization
Cambuckle Strap
Cambuckle Straps are attached to
bolt plates. The bolt plates allow for a
convenient connection to the base at the pivot
bolt. The straps are 8 feet long. They are
provided with an S' hook. The strap webbing is
2" wide black nylon. Cambuckle breaking
strength 2,000 lbs.
Hook breaking strength 2,500
lbs. Bolt plate breaking strength 3,500
lbs. Webbing breaking strength 6,000 lbs.
Tablock Pin
Special pins were selected for
ease of use. These pins incorporate a self
contained means of retaining the pin. No cotter
pins, lanyards, etc. This feature allows for
ease of use even with heavy fire scene gloves.
Pins are 3/8" diameter grade 8 for superior
strength. Note Our grade 8 pins have an olive
green plating to distinguish them from standard
grey zinc plated grade 2 pins. Use only grade 8
pins. Strength 10,000 lbs double shear
8
Res-Q-Jack Vehicle Stabilization
Clevis Pin Self Locking Cotter Pin A standard
3/8" diameter grade 8 clevis pin is used to
connect the jack unit to the base. Here a self
locking cotter pin, or bowtie cotter is used. A
standard clevis pin arrangement is used here to
avoid interference with other moving parts near
the base. Note Our grade 8 pins have an olive
green plating to distinguish them from standard
gray zinc plated grade 2 pins. Use only grade 8
pins. Double shear strength 10,000 lbs RJ-3
Extension Tubing
Telescopic tubing is used to offer
adjustability to stands. Only two sizes, 2" (12
gauge) and 2-1/4" (12 gauge) are utilized to
minimize variation. This feature coupled with
stepped end fitting design also eliminates time
consuming thought in constructing pieces to meet
the situation. Tubing is perforated on all four
sides with 3/8" holes for tablock pins on 1"
centers. Tubing is galvanized. Maximum column
load for 2" tube, 6 feet long 9,140 lbs.
CUSTOM LENGTHS AVAILABLE