M'Matveev - PowerPoint PPT Presentation

About This Presentation
Title:

M'Matveev

Description:

1.0 BX input latching _at_ 80MHz and multiplexing with FIFO - 1.5 BX sorting '3 out of 18' ... latches, data buffers, comparators, DS/DTACK logic, CSR0) CCB ... – PowerPoint PPT presentation

Number of Views:54
Avg rating:3.0/5.0
Slides: 15
Provided by: mikhail50
Learn more at: http://padley.rice.edu
Category:
Tags: latching | matveev

less

Transcript and Presenter's Notes

Title: M'Matveev


1
EMU Muon Port Card Project
M.Matveev Rice University March 20,
2002
2
MPC Functions
One board per CSC Sector (8 or 9
chambers), Resides in the middle of the
peripheral VME 9U crate. Receives up
to 2 muons from each of 8 or 9 Trigger
Motherboards every 25 ns Selects 3 best
muons out of 18 possible Transmits these 3
muons in ranked order to Sector Processors
residing in the counting room over three
100 m optical cables every 25 ns
3
MPC Block Diagram
VME J1 CONNECTOR
9U x 400 MM BOARD
VME INTERFACE
UCLA MEZZANINE CARD (XCV600E)
CCB
CCB INTERFACE SORTING LOGIC INPUT ANDOUTPUT FIF
O
CCB
TMB_1
SER
OPTO
TMB_2
CUSTOM PERIPHERAL BACKPLANE
3 OPTICAL CABLES TO SECTOR PROCESSOR
TMB_3
TMB_4
SER
OPTO
TMB_5
TMB_6
SER
OPTO
TMB_7
FINISAR FTRJ-8519-1-2.5 OPTICAL TRANSCEIVERS
TMB_8
TLK2501 SERIALIZERS
FPGA
TMB_9
SN74GTLP18612 GTLP TRANSCEIVERS
4
Sorter FPGA
MUON 1
DFF
PIPELINE MUON 1
TMB 1
MUX
DFF
MUX
4
FIFO_B MUON 1
VME
FIFO A
VME
PIPELINE MUON 2
MUX
DFF
MUON 2
DFF
4
VME
FIFO A
FIFO_B MUON 2
TMB 2
VME

MUON 3

DFF

TMB 9
VME
FIFO_B MUON 3
54
SORTER 3 OUT OF 18
CCB
VME
9
CCB INTERFACE
WINNER
5
FPGA Requirements
9 input links from Trigger Motherboards,
32-bit _at_ 80 MHz per link (288 inputs
total) 3 output links to data serializers,
16-bit _at_ 80 MHz per link (48 outputs
total) 1 output status link (winners)
9-bit _at_ 80 MHz to TMBs Input and output
FIFO buffers for testing purposes
Interfaces to VME and Clock and Control
Board (CCB) (75 inputs and outputs
total for both) FPGA should have 470
input/output pins and 28 Gbps total
bandwidth
6
TMB - to - MPC Frame Format
7
MPC to SP Frame Format
8
CSC Numbering scheme
In the present design the CSC_ID1 corresponds
to TMB1 on the peripheral backplane,
CSC_ID2 corresponds to TMB2 and so on
T M B
T M B
T M B
T M B
T M B
T M B
T M B
T M B
T M B
D M B
D M B
D M B
D M B
D M B
D M B
D M B
D M B
D M B
M P C
C C B
1
2
3
4
5
6
7
8
9
9
Preliminary results of FPGA Design
Targeted to Xilinx XCV600E-7FG680 FPGA
(UCLA mezzanine card) 461/512
input/output pins used (89) 5009/6912
slices used (72) 42/72 BlockRAMs used
(58) 44.13 Mhz maximum performance (FPGA
Express synthesis)

Latency 100.0 ns (4.0 BX) total
FPGA latency including - 1.0 BX input
latching _at_ 80MHz and multiplexing with FIFO
- 1.5 BX sorting 3 out of 18 - 0.5 BX
data merging - 0.5 BX output multiplexing
and latching _at_80MHz - 0.5 BX data latching
into TLK2501 serializers 24 ns
serialization delay (TLK2501 transmitter _at_ 80 MHz)
10
MPC Board Design Status
GTLP Backplane Interface to 9 TMBs
(completely defined) Mezzanine Card pin
assignment done A24D16 VME Interface
based on glue logic (address latches,
data buffers, comparators, DS/DTACK logic,
CSR0) CCB Interface is completely defined
Optical Data Format to SP has been agreed
Preliminary FPGA design is done
(XCV600E-7FG680) MPC draft specification is
prepared Schematic design 80 completed
6 free FPGA were obtained (Xilinx donation)
Mezzanine cards are ordered through UCLA
11
CCB for Track Finder Crate
Same CCB for peripheral and Track Finder
crates 20 sets (main 9U board Altera-based
mezzanine card) have been fabricated so
far 15 boards are assembled and tested
2 boards will be used for Track Finder tests (UF
Rice)
12
TTCrx Clock40Des1 Jitter
New TTCrx
Old TTCrx
13
Optical Test with TTCrx
C C B
T T C V I
B I T 3
T T C V X
ERROR

TTCrx

O P T O
O P T O



PC




100 m
Clock multiplier


40 Mhz


VME 9U
VME 6U
1 m
100 m
COPPER CABLE
OPTICAL CABLE
OLD AND NEW TTCrx BOARDS WERE TESTED
WITH 40.00 Mhz CLOCK SOURCE FROM TTCvx
MODULE 40.00 Mhz CLOCK WAS MULTIPLIED BY 2
BY AV9170 CHIP
NO ERRORS OBSERVED IN PRBS TEST FROM ONE
OPTOBOARD TO ANOTHER AT 80.00 Mhz (BER lt
10-13 c-1)
14
TTCrx Clock40Des1 Jitter

Conclusion Jitter is lower for the newest
TTCrx ASIC (Version 3.1, 12/2001) Jitter
increases if the broadcast commands and L1A are
transmitted from TTCvi/TTCvx Jitter
distribution for ASIC Ver.3.1 is close to
gaussian. Jitter distribution for old ASIC
looks differently Jitter is lower if
the new ASIC is powered from 5V Jitter
introduced by any of two TTCrx ASICs and other
components in the clock distribution circuitry at
our testing setup is tolerable for TLK2501
transceivers operating at 80.00 Mhz
Write a Comment
User Comments (0)
About PowerShow.com