Programming

1
Programming

• A-dec 500/300

2
Learning Objectives

• As a result of this training you will be able to
• Identify an A-dec 500 touchpad from an A-dec 300
  touchpad
• Configure handpieces on an A-dec 500 and A-dec
  300 unit

3
A-dec 500 Touchpads

• Standard Touchpad, Assistants or Doctors
• Deluxe Touchpad (2004 2006)
• Endo Deluxe (May 2006)

4
Standard Touchpad Pg 52

• System Status LED
• Dental Light Control with 3-Way Switching
• Manual Chair Positioning
• Program Button
• Presets
• Cup Fill / Bowl Rinse
• Only if a Cuspidor is installed
• Auxiliary Buttons
• A-dec relay functionality only if a Cuspidor is
  not installed

5
Chair Programming Pg 53

• Position Programming
• Position the chair to the desired operating
  position, using the manual controls (arrows) on
  the touchpad or foot switch.
• Press and release Program button (one beep).
• Within four seconds, press a position button
  (three beeps).
• Position 3 (X-ray/Rinse)
• Press and hold Program and Position 3at the same
  time for three seconds. One beep confirms that
  the button 3 is now fully programmable.
• Note Disabling the x-ray/rinse function is a
  global function for Dr. A and B.

6
Cuspidor Functions Pg 54

• Cuspidor Factory Presets
• Cup fill 2.5 seconds
• Bowl rinse 30 seconds

7
Stand-alone Cuspidor

• After March, 2008
• Hold BOTH cup fill and bowl rinse buttons on the
  cuspidor tower down for 3 seconds. Release BOTH
  buttons.
• Select cup fill OR bowl rinse to program for the
  desired (program) time.
• When the desired program time (amount of water)
  has been achieved, release the button. Three
  beeps indicates the cup fill or bowl rinse is now
  programmed.

8
Handpiece Configuration
2
3

• Overview

1
0
4
9
Handpiece Configuration

• Press Program and Doctor A/B buttons

10
Deluxe Touchpad Pg 56

• Allows switching between Standard and Endo use of
  the EA51LT Electric Motor
• Mode change
• Select with E button
• 4 memory settings
• M12,000 RPM
• M210,000 RPM
• M320,000 RPM
• M440,000RPM

11
Deluxe Touchpad Pg 57

• Dual Operator Support
• Auxiliary Buttons
• Cup Fill / Bowl Rinse
• Only if a Cuspidor is installed
• If a Cuspidor is not installed,buttons are
  inactive
• Water Coolant / Air Coolant
• Electric Handpiece / Ancillary Controls

12
Programming Pg 58-60
13
Deluxe Touchpad Displays

• Turbine selected
• More than one of theBig Three selected
• Scaler
• Electric Handpiece
• Pneumatic Handpiece
• No Holdback Air
• The power is on but there isnt anyair to the
  unit

14
Touchpad Programming

• Factory Preset Functions
• Disable/Enable the Footswitch or Touchpad
• Place the spare jumper in the EN/DIS TP/FS
  position of the test points header.
• Push the buttons to be disabled/enabled (PRGM,
  PRGM 0, PRGM 1, PRGM 2, PRGM 3).
• One beep means the button is disabled.
• Three beeps means the button is enabled.
• Place the spare jumper back in the spare position.

15
A-dec 300 Deluxe Touchpad

• Programmable chair positions
• X-ray/rinse button
• Cupfill/bowl rinse
• Auto Light
• Electric handpiece operation
• Endodontics

16
Deluxe Touchpad Setup
17
Thank you!

• What questions do you have?