Nessun titolo diapositiva

1
(No Transcript)
2
Completely new

• Endos DC has been designed from scratch.
• Every component of the system is completely new
• new generator
• new tubehead
• new arm
• new timer

3
New generator

• High frequency, constant potential technology
  with ripple lower than 2.
• Inverter operating at 100kHz frequency. This
  value is at the highest levels in the market.
• The two features above help in giving the maximum
  energy efficiency ant to keep the patient dose as
  small as possible.

4
New generator

• Duty cycle 115, adaptive.After a 200ms
  exposure, you just have to wait 3.2 seconds for
  the next exposure. The adaptive duty cycle,
  automatically sets the waiting time according to
  loading conditions.
• Exposure parameters 65kV, 4/5 mA
• with DLC technology

5
New generator

• The choice of a single high voltage (65kV)
  optimizes the range of visible gray levels by
  operating in the optimal dynamic range of digital
  detectors and films
• This value gives the best representation of all
  the interesting anatomic structures.

6
DLC Technology

• DLC Dual Low Current
• It is possible to select two anodic current
  values 4 or 5 mA.
• The two mA values and the 65kV high voltage have
  been studied to give the best results with
  digital sensors and high speed films
• Those values allow to operate with highly stable
  and repeatable times (not too short, thus
  unstable not too long, thus subject to patient
  movement)

7
Energetic efficiency

• Endos DC has been designed to make the best use
  of the electric energy taken from the mains
• Endos DC is already compliant to the forthcoming
  IEC standards on the reduction of the mains
  harmonics which will be in force starting from
  2004

8
New Tubehead

• Compact design
• 0.7mm focal spot
• weight 4.5 kg
• new design
• accessories
• 30cm cone
• 35x45mm collimator

9
New arm
10
New timer

• Selection of 4 receptors
• Standard film (5mA)
• High speed film (5mA)
• Digital (4mA)
• Programmable (4 or 5mA)
• The selection of the receptor optimizes
• Current (4 or 5 mA)
• Exposure times (depending also on the selected
  tooth)

11
New timer
Anodic current 4/5mA indication
30cm cone indication
X-ray on indication
Manual time selection
Ready indication
Patient size selection
Anatomic tooth selection
X-ray pushbutton
Receptor selection
12
New timer

• A control on the keyboard, with a signal lamp,
  can be used to automatically increase the
  exposure times when the 30cm extension cone is in
  use
• Display brightness adjustment
• Automatic compensation of mains fluctuations
• Exposure times from 0.01 to 2 s

13
Remote timer

• Gives complete control over the system from
  outside the examination room.
• The same keyboard installed on the local timer
  can be removed and installed outside the room by
  means of a simple adapter kit

14
Remote Timer

• Connection is made with a simple telephone-type
  connector
• Its possible to convert a local system into a
  remote system at any time by using an adaptation
  kit

15
Connectivity

• Endos DC incorporates a RS232 serial interface
  which will allow in the future to communicate
  with external devices and perform service
  functions

16
Configurations

• Mounting options
• standard wall mount with 30, 60, 80cm extension
  arms
• wall mount with remote timer keyboard
• Mobile

Wall mounted units can be installed using two
(single stud) or three fixation holes. Two holes
out of three are compatible with Explor-X 70
holes.
17
Service

• Average installation time 4 hours, 1 technician
• Tubehead replacement
• 1 hour, one technician
• Minimum adjustments required